ATD Tools ATD-7372 user manual

Summary of the content on the page No. 1

Air Hydraulic
Bottle Jacks
Operating Instructions & Parts Manual
Model Number Capacity
ATD-7370 12 Ton
ATD-7371 20 Ton
ATD-7372 20 Ton (low profile)
U.S. Patent No’s. 5,341,723 • 5,946,912

This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
!
Obey all safety messages that follow this symbol to avoid possible injury or death.
! ADvErTEncIA ! WARNING
To avoid crushing and related injuries:
• Leer, comprender, y seguir las instrucciónes antes

Summary of the content on the page No. 2

SAFETY and GEnErAL InFOrMATIOn Save these instructions. For your safety, read, understand, and follow the information provided with and on this jack before using. The owner and operator of this equipment shall have an understanding of this jack and safe operating procedures before attempting to use. The owner and operator shall be aware that use and repair of this product may require special skills and knowledge. Instructions and safety information shall be conveyed in the operator's native

Summary of the content on the page No. 3

! WARNING ! WARNING • Study, understand, and follow all printed materials provided with/on this product before use. X • Do not exceed rated capacity. • This is a lifting device only! To avoid crushing and related injuries: • Immediately after lifting, support the load with • never work on, under or around a load supported a pair of appropriately rated jack stands. only by hydraulic jack. • Use only on hard, level surface. • Always use adequately rated jack stands. • Do not use adapt

Summary of the content on the page No. 4

OPErATIOn raising the ram Plunger 1. Assemble handle, ensure that spring clips align with slots. 2. Place vehicle in the park, with emergency brake on and wheel securely chocked to prevent inadvertent vehicle movement. 3. Locate and close release valve by turning handle clockwise until firm resistance is felt to further thread engagement. 4. Verify lift point, center jack saddle under lift point. 5. Squeeze the lift control valve or insert handle into handle sleeve and pump to contact lift poi

Summary of the content on the page No. 5

TrOUBLESHOOTInG Possible causes corrective Action Symptom Jack will not lift load • Release valve not tightly closed • Ensure release valve tightly closed. • Overload condition • Remedy overload condition. • Air pressure inadequate • Ensure adequate air pressure. Jack will lift, but not maintain • Release valve not tightly closed • Ensure release valve tightly closed. pressure • Overload condition • Remedy overload condition. • Hydraulic unit malfunction • Contact ATD Tech. Service. Jack will

Summary of the content on the page No. 6

rEPLAcEMEnT PArTS (refer to page 6 & 7) Not all components of the jack are replacement items, but are illustrated as a convenient reference of parts location. When ordering parts, give part number and parts description. Call or write for current pricing: ATD Tools Inc. 160 Enterprise Drive, Wentzville, MO 63385. Tel:(636)327-9050 Fax:(636)327-9044 replacement Parts Illustration for model ATD-7370, ATD-7371, & ATD-7372 23 25 10 10 11 a 8 9 1 21 b c 2 8 12 22 12 22 19 18 k 17 d 24 e 16 f 15 3a

Summary of the content on the page No. 7

replacement Parts List for model ATD-7370, ATD-7371 & ATD-7372 Item Part# for ATD-7370 Part# for ATD-7371 Part# for ATD-7372 Description Qty. 1 A120-10004-000 A190-10002-000 Cylinder Fastener 1 2 A120-10003-000 A190-10001-000 Guide Ring 1 3a 5905-00100-200 N/A Filler Plug 1 3b N/A G62S-03301-000 Filler Screw 1 4 A120-10002-000 Special Washer 2 5 5905-00054-000 Seal 1 6 BT10-24001-000 Release Valve 1 7 5308-00095-000 Gasket 2 8 A27010-0001 A27060-0003 Air Motor 1 9 A27010-0002 N/A Air Inlet Swive

Summary of the content on the page No. 8

ATD Tools Inc. 160 Enterprise Drive, Wentzville MO 63385 636-327-9050 8