Summary of the content on the page No. 1
20” LCD Television
FLM-2017
20061107
Summary of the content on the page No. 2
Table of Contents 1 Important Safety Instructions------------------------------------------------ 3 Product Features ---------------------------------------------------------------- 4 Front Panel------------------------------------------------------------------------- 6 Rear Panel-------------------------------------------------------------------------- 7 Remote Control------------------------------------------------------------------- 9 System Connections------------------------
Summary of the content on the page No. 3
Important Safety Instructions The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (serv
Summary of the content on the page No. 4
Important Safety Instructions Note: 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Maintain well ventilated conditions around the product. Do not put product on bed, sofa or anything that blocks ventilation. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such a
Summary of the content on the page No. 5
Product Features This product incorporates LCD display and TV receiver in one system. AV and VGA Input Multiple Mode Can be connected external audio and video Component mode signal source and PC. VGA mode TV mode Special Function Composite mode Supports sleep timer setting and V-Chip S-VIDEO mode function. High Quality Property Multi-audio and Multi-video modes High Resolution Supports multi-audio and multi-video
Summary of the content on the page No. 6
Front Panel 1. 20" color TFT screen 20" color TFT screen clearly show the data. 2. SOURCE button Press to select the modes: Component, VGA, TV, Composite or S-VIDEO. 3. MENU button Press to enter or exit setup menu. 4. CH + /CH- button In the TV mode, press to select channels. In setup menu, the same function as ▲/ ▼ direction buttons. 5. VOL+ /VOL-button In the TV mode, press to decrease or increase the volume. In setup menu
Summary of the content on the page No. 7
Front Panel 6. POWER button Press to enter or exit the standby mode. 7. Earphone Jack When connected to earphone, the internal speakers will automatically turn off. 8. Remote Sensor Remote sensor window for the remote control. 9. Power Indicator In normal playback status, it is blue; in standby mode, it turns red. 10. Speakers Two speakers output high quality stereo sound. - 6 -
Summary of the content on the page No. 8
Rear Panel 1. Y/Pb/Pr Input Jack Connected to the Y/Pb/Pr input in Component mode 2. L/R Audio Input Jack Connected to the L/R audio input in Component mode. The L/R audio input jacks can also be used in S-Video mode. 3. AV Output Jacks Connected to the external AV input device. 4. S-Video Input Jacks In the S-VIDEO mode, connected to S-VIDEO signal input. 5. TV Signal Input Jack Connected for the ex
Summary of the content on the page No. 9
Remote Control In the TV mode, press to return to the Remote Control Drawing channel last viewed. 4. VOL +/- button Press to increase or decrease the volume. 5. SLEEP button Press to select sleep time. 6. MUTE button Press to turn on or off the speaker output. 7. Direction buttons ( ▲▼◄ ►) In the setup menu, press the ▲▼button to select the desired item and press the ◄► button to adjust or set. 8. OK button Press to confi
Summary of the content on the page No. 10
Remote Control Preparation of Remote Control Using of Remote control Push the back cover to open the battery Point the remote control unit from no more than compartment. about 7m from the remote control sensor and within about 60 degrees of the front of the unit. Insert two batteries (1.5V, size AAA), please make sure the polarity matches the marks inside the compartment. Press the back cover
Summary of the content on the page No. 11
System Connections • Do not connect the power cord until all other connections have been made. • Ensure that you observe the color-corded cables when connecting audio and video cables. Connecting to External AV Signal Source Use the audio and video cable to connect the AV input jacks on the rear panel of the unit to the external AV signal source. Use the S-VIDEO cable to connect the S-VIDEO input jack on the rear panel of the unit to the external AV signal sour
Summary of the content on the page No. 12
System Connections Connecting to External AV Signal Source (YPbPr) Use the audio and video cables to connect the YPbPr (Component) input jacks on the rear panel of the unit to the external AV signal source. After making all AV connections, turn on the power of the unit and external AV signal source and press the SOURCE button to shift to Component mode. - 11 -
Summary of the content on the page No. 13
System Connections Connecting to External AV Device(AV Out) The unit supports audio and video signal input function, it can be connected to the external audio and video device. Use the audio and video cables to connect the AV output Jacks on the rear panel of the unit to the external AV input device. - 12 -
Summary of the content on the page No. 14
System Connections Connecting to PC The unit can be connected to PC (personal computer) via the VGA cable. Follow the steps and the figure below to connect: 1. Connect one end of the VGA cable to the VGA input jack on the rear panel of the unit. 2. Connect the other end to the PC. 3. Connect one end of the audio cable to the PC audio input jack on the rear panel of the unit. 4. Connect the other end to the PC audio output jack. 5. Set the PC’s resolution at 80
Summary of the content on the page No. 15
System Connections Connecting to Headphones This unit can be connected to an earphone for listening music in private. See below figure for details: After connecting to the earphone, the internal speakers’ output will turn off automatically. Connecting to Power Adapter Power is supplied through the provided appropriative power adapter, one end is connected to the DC 9.5/12V IN jack on the rear panel of the unit, the other end to the AC10
Summary of the content on the page No. 16
System Connections Connecting to TV Antenna This unit can be connected to the TV signal input source via the TV jack on the rear panel. After making all connections, turn on the power of the unit and press the SOURCE button to shift to TV mode. When channel system is set to Antenna, you can select channels from 2 to 69: For 2~9 channels: Press the number buttons to select channel X, wait five seconds to go to the selected cha
Summary of the content on the page No. 17
directly . * X is the channel number. TV Setup and Operation Preparations 1. After making all connections, press the POWER button to turn on the power. (If it is turned on, the power indicator is blue.) 2. Press the SOURCE button to shift to TV mode. You can go on with the following operations: Image Setting Note: This item is only available when there is signal input. Press the MENU button once to enter the setup menu, as shown on the right: In the set
Summary of the content on the page No. 18
TV Setup and Operation Contrast Setup Press the ▲▼ button to select Contrast and press the ◄► button to adjust the value. Press the MENU button to return to the previous menu. Hue Setup Press the ▲▼ button to select Hue and press the ◄► button to adjust the value. Press the MENU button to return to the previous menu. Saturation Setup Press the ▲▼ button to select Saturation and press the ◄► button to adjust the value. Press the MENU button to return to t
Summary of the content on the page No. 19
Bass Setup Press the ▲▼button to select Bass and press the ◄► button to adjust the level. Press the MENU button to return to the previous menu. TV Setup and Operation Treble Setup Press the ▲▼button to select Treble and press the ◄► button to adjust the level. Press the MENU button to return to the previous menu. Balance Setup Press the ▲▼ button to select Balance and press the ◄► button to adjust the level. Press the MENU button to return to the previous menu.
Summary of the content on the page No. 20
TV Setup and Operation Parental Setting Note: The Parental Function is the same as that of V-CHIP. Press the MENU button to enter the setup menu. Press the ▲▼ button to select Parental and press the ENTER button to enter the menu shown on the right. In the Parental setup menu, press the ENTER button and use the number buttons to enter the pin. The default pin is 1111. Press the ENTER button to continue and display the menu
