Summary of the content on the page No. 1
TECHNICAL MANUAL (Ver. 2.0)
PLASMA DISPLAY MONITOR: PDP-502MX
TABLE-TOP STAND: PDK-5001
PLASMA DISPLAY CEILING SUSPENSION HARDWARE: PDK-5002
PDP BRACKET: PDK-5005
PLASMA DISPLAY WALL-MOUNT HARDWARE: PDK-5006
CARRIABLE STAND: PDK-5008
SPEAKER SYSTEM: PDP-S03-LR
This manual provides precautions and information for installation, preparation, and handling of the plasma display and
its dedicated mounting hardware.
Before installation and preparatory work, choose a safe and appropriate site after thor
Summary of the content on the page No. 2
Table of Contents FEATURES ..................................................................................................................................................................................... 4 SPECIFICATIONS 2.1 Specifications ..................................................................................................................................................................... 6 2.2 External Dimensions ...............................................................
Summary of the content on the page No. 3
Table of Contents 5.2 Normal Operating Mode................................................................................................................................................... 93 5.2.1 About normal operating mode ................................................................................................................................. 93 5.3 Menu Mode .............................................................................................................................
Summary of the content on the page No. 4
Features Features and Functions of the PDP-502MX Plasma Display High definition, high contrast • Through the newly-developed panel that aims for the optimum in luminous efficiency and development of a new drive sequence, we have achieved high contrast and a great improvement in brightness while maintaining high definition. High quality, clear picture • By digitalizing the signal processing circuit, we have made possible clear, precise image representation for all types of input signal (PC, video
Summary of the content on the page No. 5
Features 5
Summary of the content on the page No. 6
Specifications 2.1 Specifications Light-emitting panel .................. 50-inch plasma display panel Audio-related Aspect ratio .................................................................... 16 : 9 AUDIO INPUT Input Pin jack (· 2) PEL .......................................................................... 1280 · 768 (for INPUT 1/2) L/R .... above 500 mVrms/10 kW PEL pitch ........................... 0.858 (H•RGB trio) · 0.808 (V) mm Gradation ..................................... 256/
Summary of the content on the page No. 7
Specifications (NOTE 1) Do not make connections to the S terminal and a BNC terminal at the same time. This could cause malfunction or breakage of the device. (NOTE 2) The display is preset at the factory to 4800bps. This setting can be changed using either the remote control unit or a PC. (NOTE 3) Allow for 500 W „ 500VA of consumption per unit. (NOTE 4) The correct operating environmental temperature may vary, depending on the installation site. (Refer to Installation Site Requirements.) INPUT
Summary of the content on the page No. 8
External Dimensions 2.2 External Dimensions Weight: 40.3 kg (without attachment stand) Material: Front: Resin; Rear frame: Resin; Rear cover: Aluminum, Front protector panel: acrylic Treatment: Front: Paint; Rear frame: Paint; Rear cover: Paint (All paints are Pioneer original colors) For packaging information, refer to 3.3.2 “Unpacking”. 31.4 : Center of gravity (Unit: mm) 609 98 65 1218 Effective screen dimensions 1098 1128 Unit operating Light sensor for the remote panel MAIN POWER switch Ce
Summary of the content on the page No. 9
External Dimensions STANDBY/ON INPUT 22.5 11.1 MENU ADJUST SET SIZE DISPLAY 29.8 21.4 9 7.8 11 48.1 146.6
Summary of the content on the page No. 10
Controls and Connectors NOTE 2.3 Controls and Connectors When the optional plasma display speakers are attached, it is not possible to use the operation panel on the display. STANDBY/ON 1 2 3 INPUT 4 MENU 5 ADJUST 6 SET 7 SIZE 8 DISPLAY 9 0 - = ~ ! @ # $ % (at the rear of the SPEAKER IN OUT IN OUT RL ANALOG OUTPUT R RS-232C 8Ω ~16Ω AUDIO OUTPUT COMBINATION CONTROL INPUT 3/4 INPUT 1/2 R G B ANALOG AUDIO INPUT INPUT 4 R G B main unit) ^ & * ( ) _ + Á
ª
£
¢
Y CB/P
Summary of the content on the page No. 11
Controls and Connectors ~ CONTROL IN/OUT terminals ( Sync Signal Impedance switch For connection to Pioneer products that have the ë mark. Used to switch impedance for items & and *. If you connect a CONTROL (If CONTROL connection is carried out) then you can carry out system control of the INPUT 2 display. ) S-VIDEO input terminal (NOTE) This product does not support RU-V107 wired _ Y/C Separate Video Input terminal remote control units. Receives signals from the Y/C separate video. ! RS 232C t
Summary of the content on the page No. 12
Controls and Connectors 2.4 Pin layout INPUT 4 (Mini D-sub, 15-pin connector; female) RS-232C terminal (D-sub 9-pin connector; male) pin layout pin layout Note : Standard VGA connector (plug and play supported). Note : Plasma communicates as a DCE derice. 5 1 1 5 6 10 15 11 6 9 Pin No. $ INPUT4 input terminals % INPUT4 output terminals Pin No. Signal 1 R or CR/PR 1 NC (not connected) 2 G or Y 2 TxD (Transmit Data) 3 B or CB/PB 3 RxD (Receive Data) 4 NC (not connected) 4 NC (not connected) 5 GND
Summary of the content on the page No. 13
Remote Control Unit 2.5 Remote Control Unit SCREEN SIZE button Used to manually select the screen size. STANDBY /ON SCREEN MUTING SIZE MUTING button STANDBY/ON button INPUT Used to temporarily turn off the Used to turn the system on or off VIDEO Y/C VOL 1 2 sound. (standby). RGB RGB (BNC) (D-sub) 34 INPUT button VOL buttons (+/–) Used to select inputs. DISPLAY Used to adjust the volume. MENU DISPLAY DISPLAY button MENU button Used to view condition of inputs Used to display the menu screen. SET
Summary of the content on the page No. 14
Remote Control Unit Case 2.6 Remote Control Unit Case Peel the sticker paper off of the lower and upper tape on the rear side of the remote control unit case, and attach it to the rear of the main unit or some other fixed surface, so that it will be available for putting away the remote control unit when it is not in use. Remote control unit Example of remote control unit case attachment Remote control unit case Upper and lower tape (NOTE) Do not obstruct the air holes in the remote control un
Summary of the content on the page No. 15
Remote Control Unit Case 15
Summary of the content on the page No. 16
Installation Site Requirements 3.1 Installation Site Requirements If the site requires modifications or special preparations for installation of the plasma display or its mounting hardware, obtain permission in advance from the building owner or building authorities. To ensure installations safety, it is also important to determine the strength of the installation site with the help of the original building contractor. Safety Precautions 1) Structure of the installation site Make sure you thoro
Summary of the content on the page No. 17
Installation Site Requirements 9) Temperature and humidity conditions • The installation site should meet the following conditions: • Operating temperatures: 0 to 40 °C (largely depending on installation conditions) • Operating humidity: 20 to 80 % • Storage temperature: –20 to 60 °C • Storage humidity: 20 to 90 % • Operating atmospheric pressure: 0.8 to 1.1 atm • Storage atmospheric pressure: 0.6 to 1.5 atm • We recommend against installing electronic products such as this unit in locations su
Summary of the content on the page No. 18
Installation Conditions 3.2 Installation Conditions 3.2.1 Heat dissipation This unit has openings for effective ventilation at locations marked by arrows in the illustration below. To allow proper dissipation of heat from the unit, avoid blocking or covering any of these openings. (Unit : mm) 60 157 80 80 80 128 Fan (4 in number) 256 53 45 137.5 453 190 160 282.5 (one side only) 53 160 235 Air flow through the openings: All four fans draw off hot air from the unit. All openings not assisted by f
Summary of the content on the page No. 19
Installation Conditions 3.2.2 Calculating heat quantity As a curtesy to our customers, we have included the power formula to calculate the air conditioning needs. For power consumption, allow for 500 W „ 500 VA per unit. Since most of the power consumed is transformed into heat, power consumption may be regarded as roughly equal to generated heat. 1 Conversion to calories [W] · 0.86 = [kcal/h] Heat generated per display: 500 W · 0.86 = 430 kcal/h 2 Conversion to British Thermal Units [W] · 3.41
Summary of the content on the page No. 20
Installation Conditions This unit is designed to be mounted using four bolt holes. For additional safety, we recommend securing it at six to eight points on opposite sides of the horizontal and vertical center lines, as shown in the illustration below. Do not secure the unit at four points arranged in a single row, as shown below. Methods for securing - Unfavorable examples Methods for securing - Favorable examples A. Secured at eight points B. Secured at six points C. Secured at four points (wi
