Summary of the content on the page No. 1
Philips Hospitality TV
Installation manual for
32HFL5007D/10
42HFL5007D/10
47HFL5007D/10
55HFL5007D/10
Version 1.1
Summary of the content on the page No. 2
Contents 1. Requirements before starting the installation .......................................................................................................... 2 2. Find out the state of the TV ...................................................................................................................................... 3 3. Re-install TV ............................................................................................................................................
Summary of the content on the page No. 3
1. Requirements before starting the installation Before starting the installation, make sure that you have everything you need at hand. Master remote control 22AV8573 or Guest remote control 22AV1109A And USB stick You will need the master remote control or the guest remote control to access the menus. To access the setup menu press the ‘RC5 SETUP’ key, and then press the ‘Home/Menu’ button. For the guest remote control, press the following keys sequent
Summary of the content on the page No. 4
2. Find out the state of the TV It is important to know if a TV is in ‘virgin mode’ (out of the box) or installed before. If you can see this screen below, you know that the TV is in ‘virgin mode’ and you can install the set. See chapter 4 of this manual. If you power on the set and then press the ‘Home’ button on the guest remote, you will see this screen appear, if the TV already has been installed or the wizard was already skipped. PBS mode on PBS mode off You can st
Summary of the content on the page No. 5
3. Re-install TV If you want to start an installation from scratch you can always re-install the TV. This can be done by using the option: Re-install TV set. If PBS is active you can access the setup menu press the ‘RC5 SETUP’ key, and then press the ‘Home/Menu’ button (For the guest remote control, press the following keys in sequence: 3,1,9,7,5,3, ‘MUTE’) , then go to TV Setup, confirm with “OK”. This menu will appear: If the PBS Menu is disabled, you can access the Setup menu wi
Summary of the content on the page No. 6
Press “OK” to access the sub-menu, navigate to “Reinstall TV”. Press “OK” to reinstall the TV set. If all is correct select “YES” and press “OK”. After this operation the TV will power off and on and display the installation wizard. Note: All settings are at default values and no channel plan is available. After reinstalling, the PBS Setup menu will keep the PBS Mode, Room ID and PBS Setup menu and reset all other parameters to default values. 5
Summary of the content on the page No. 7
4. Installation wizard When you turn on the TV for the first time, or you have reinstalled the TV, you should see the following screen. Here you will need to select your preferred language. After this, you will need to select the country. Depending on the country selection, some pre-defined settings will be activated, because of local broadcast requirements. Example: digital/analog channels could be disabled; reordering and deleting channels can in some cases not be possible. N
Summary of the content on the page No. 8
The next step is to select ‘Wall mounted’ or ‘On a TV stand’. This option changes some settings for the audio and image of the TV. Now you can select the visual and hearing impaired options. If you select ‘On’, your TV will automatically turn on settings to help visual and hearing impaired people. THE MOST COMMON OPTION IS TO TURN THIS FUNCTION OFF. On the following page we can start the channel installation wizard. You can also press “Back” to correct any previous setting. W
Summary of the content on the page No. 9
For the channel installations, select ‘Install TV channels’ and press ‘OK’ Then you can select ‘Continue’ and press ‘OK’ again. Here you can select the type of channels you would like to install and what preference you will use. It is advisable to check the settings before starting the search. 8
Summary of the content on the page No. 10
Note: If all options are disabled you have to go down to the Digital channels option and set the digital channels to ON. A screen is displayed to make changes to set the channel list/map configuration: [Symbol rate mode]: Automatic TV will use the preset Symbol rate (6.900/6.875) Manual Option to set Symbol rate 1 and Symbol rate 2 [Symbol rate 1]: 0.000 (to set) [Symbol rate 2]: 0.000 (to set) The “Frequency scan” contains two options: - “Quick”: this is a fast method to se
Summary of the content on the page No. 11
Frequency step size has two options: 1. “1 MHz” – With Full scan, the step size to search for channels is 1 MHz. The scan will take more time but will find also channels broadcasted not according to the channel grid. 2. “8 MHz (default)” – With Full scan, the step size to search for channels is 8 MHz. The scan will be shorter in time but some channels which are not in the expected channel grid (local head-end) will not be found. When details of the local network are known they
Summary of the content on the page No. 12
During the channel search you can see the progress bar and how many channels are found at that time. When the search is done, you should see “Channel search complete” and a summary of the channels found. In this case: Digital channels found: 53 Analogue channels found: 0 Press the “OK” button on the remote control to finish the search. If you would like to change the picture and sound settings, you can go to “Optimize TV picture and sound” and press the “OK” button
Summary of the content on the page No. 13
The wizard will ask you some questions about which image you prefer, select the option you desire and press “OK” on the remote control. Once this wizard is done, you will return to the installation menu again. The network wizard will guide you through network setup. This wizard will popup: 12
Summary of the content on the page No. 14
Please select “Next” and press OK to continue The connection will be made to wireless network or via wired network, depending on preferences. TV will automatically acquire an IP address if this is available via DHCP. After the connection is made, the result is shown on the TV. The last option in this menu is “Add your devices”. This can be done if you would like to add a DVD player or STB. 13
Summary of the content on the page No. 15
When you are done with this, select “Done” and press ‘OK’ on the remote control. After pressing “Done” you have completed the installation of the TV and you should see this screen. Press “OK” on the remote control to exit this wizard. Note: This wizard will not be available anymore when you start the TV the next time. The only way to re-use this wizard is to reinstall the TV set. 14
Summary of the content on the page No. 16
5. Channel options a. Reordering channels For reordering TV channels the channel plan from PBS Setup must be used. In consumer menu you cannot rearrange channels. The PBS Setup can be accessed by using the Yellow remote (RC 22AV8573 Master Remote control) and pressing the MENU Button or with the TV remote press 3,1,9,7,5,3, MUTE). The PBS menu will appear like in picture. Go to the option Channel setup and press “OK” to access the submenu. The channel grid will contain all installed
Summary of the content on the page No. 17
Navigate to the channel that you want to move and press “OK” on the remote control to select that channel. The arrows around the channel indicate that the channel is selected and can be moved. Use the arrow keys to move the channel to the new position. When you reached the new position press “OK” on the remote control to confirm the new position of the channels. Once you are finished with the reordering, press “Options” on the remote control again. 16
Summary of the content on the page No. 18
Press “OK” on the remote control to confirm that you are done with the re-ordering. b. Rename channels Select the channel, press the “Options” button on the remote control and select “Rename” to change name of a channel. If you then press the “OK” button a virtual QWERTY keyboard will pop up. c. Hide channels Important: You cannot delete channels from the channel grid, but you can use the option to hide the channels. Select the Channel, press the “Options” button and select “Hide c
Summary of the content on the page No. 19
6. Professional Setup [Professional Settings] Select the Setup menu language to be English, French, German or Italian. [Professional Mode] [Off]: The TV operates as a basic (consumer) TV. [On]: All settings in the PBS mode Setup menu are active. Only by switching on this mode the TV will act as a Hospitality TV. [NetTV] [Configure Net TV] allows you to disable/enable the Net TV portal provided by the Philips Net TV server. If you select [Configuration], [Hotelier]
Summary of the content on the page No. 20
[Icon Label] Change the label of the [Browse Portal] icon. [Portal URL] Enter the URL to access from [Browse Portal]. The address is for the SmartUI external server. [Room ID] Entry field to store 4 digits to set the Room Identifier. Room ID can be used to distinguish between different floors/rooms/setups when using SmartInstall. [Switch on volume] When the guest switches the TV on, it will play at the specified volume level. Selectable value from 00 until 60.
