Summary of the content on the page No. 1
Philips Hospitality TV
Installation Manual for
22HFL30x7x/10
26HFL30x7x/10
32HFL30x7x/10
42HFL30x7x/10
Version 1.1
Summary of the content on the page No. 2
Contents 1. Requirements before starting the installation .......................................................................................................... 2 2. Find out the state of the TV ...................................................................................................................................... 3 3. Re-install TV ............................................................................................................................................
Summary of the content on the page No. 3
1. Requirements before starting the installation Before starting the installation, make sure that you have everything you need at hand. Master remote control 22AV8573 or Guest remote control 22AV1108A And USB stick You will need the master remote control or the guest remote control to access the menus. To access the setup menu press the ‘RC5 SETUP’ key, and then press the ‘Home/Menu’ button. For the guest remote control, press the following keys sequential: 3
Summary of the content on the page No. 4
2. Find out the state of the TV It is important to know if a TV is in ‘virgin mode’ (out of the box) or installed before. If you can see this screen below, you know that the TV is in ‘virgin mode’ and you can install the set. See chapter 4 of this manual. If you power on the set and then press the ‘Home’ button on the guest remote, you will see this screen appear, if the TV already has been installed or the wizard was already skipped. Professional Settings ON Professional Sett
Summary of the content on the page No. 5
3. Re-install TV If you want to start an installation from scratch you can always re-install the TV. This can be done by using the option: Re-install TV set. If Professional mode is active you can access the setup menu by pressing the ‘RC5 SETUP’ key, and then press the ‘Home/Menu’ button (For the guest remote control, press the following keys in sequence: 3,1,9,7,5,3, ‘MUTE’) , then go to TV Setup, confirm with “OK”. This menu will appear: If the Professional mode is disabled, you
Summary of the content on the page No. 6
Press “OK” to access the sub-menu, navigate to “Reinstall TV”. Press “OK” to reinstall TV set. If all is correct select “Start now” and press “OK”. After this operation the TV will power off and on and display the installation wizard. Note: All settings are at default values and no channel plan is available. 5
Summary of the content on the page No. 7
4. Installation wizard When you turn on the TV for the first time, or you have reinstalled the TV, you should see the following screen. Here you will need to select your preferred language. Please select with Up and Down arrow keys and confirm with ‘OK’ or press the Left arrow key. After this, you will need to select the country. Depending on the country selection, some pre-defined settings will be activated, because of local broadcast requirements. Example: digital/analog channels c
Summary of the content on the page No. 8
The next step is to choose between ‘Shop’ and Home’ use. If you select “SHOP” an ‘e-sticker’ banner will be displayed on the TV. This is for commercial purpose only. Now you can select the visual and hearing impaired options. If you select ‘On’, your TV will automatically turn on settings to help visual and hearing impaired people. THE MOST COMMON OPTION IS TO TURN THIS FUNCTION OFF. On the following page we can start the channel installation wizard. You can also press “Back”
Summary of the content on the page No. 9
For the channel installations, select ‘Install TV channels’ and press ‘OK’ Then you can select ‘Continue’ and press ‘OK’ again. Here you can select the type of channels you would like to install and what preference you will use. 8
Summary of the content on the page No. 10
It is advisable to check the settings before starting the search. The “Frequency scan” contains two options: - “Quick”: this is a fast method to search channels but it might skip some channels (depending on the network). - “Full”: the scan will search on all frequencies and will store all channels available. This is the safe method if you don’t know the network parameters, but it takes more time. - Advanced: If you know the network parameters like Network ID, Network Freq
Summary of the content on the page No. 11
The Symbol Rate options are: Automatic and Manual. If you do not know the correct values for this option, please use the Automatic option. Analogue channel: If you don’t have or you don’t want to install analogue channels, you can disable the search for this type of channels. The “Reset” option will reset the search settings to default. After you have checked or changed settings, you can select “Done” and select “Start” to start the channel search. During the channel search you can
Summary of the content on the page No. 12
If you would like to change the picture and sound settings, you can go to “Optimize TV picture and sound” and press the “OK” button on remote control. A wizard will start to guide you through the process of setting the sound and picture on the TV set. Select “Continue” to start the wizard and press the “OK” on remote control. The wizard will ask you some questions about which image you prefer, select the option you desire and press “OK” on the remote control. Once this wiz
Summary of the content on the page No. 13
After pressing “Done” you have completed the installation of the TV and you should see this screen. Press “OK” on the remote control to exit this wizard. Note: This wizard will not be available anymore when you start the TV the next time. The only way to re-use this wizard is to reinstall the TV set. 12
Summary of the content on the page No. 14
5. Channel options a. Reordering channels To reorder TV channels you need the channel plan from the Professional Settings menu. In the consumer menu you cannot rearrange channels. The Professional Settings menu can be accessed by using the Yellow remote (RC 22AV8573 Master Remote control) and pressing the MENU Button or with the TV remote press 3,1,9,7,5,3, MUTE). The Professional Settings menu will appear like in the picture below. Go to the “Channel setup” option and press “OK” to a
Summary of the content on the page No. 15
Select “Reorder” and Press the “OK” button on the remote control to reorder channels. Navigate to the channel that you want to move and press “OK” on the remote control to select that channel. The arrows around the channel indicate that the channel is selected and can be moved. Use the arrow keys to move the channel to the new position. When you have reached the new position press “OK” on the remote control to confirm the new position of the channels. Once you finished with the reor
Summary of the content on the page No. 16
b. Rename channels Select the channel, press the “Options” button on remote control and select “Rename” to change name of a channel. If you then press the “OK” button a virtual QWERTY keyboard will pop up. c. Hide channels Important: You cannot delete channels from the channel grid, but you can use the option to hide the channels. Select the Channel, press the “Options” button and select “Hide channels”. You will see an “H” in the channel square. Select “Show hidden channels” i
Summary of the content on the page No. 17
6. Professional Settings [Professional Settings] Settings especially designated for hospitality. [Professional Mode] [Off]: The TV operates as a basic (consumer) TV. [On]: All settings in the Professional Settings Setup menu are active. Only by switching on this mode the TV will act as a Hospitality TV. [Room ID] Entry field to store 4 digits to set the Room Identifier. Room ID can be used to distinguish between different floors/rooms/setups when using SmartI
Summary of the content on the page No. 18
[USB to TV] Check Cloning section [TV to USB] Check Cloning section [RF to TV] Option used for SmartInstall Note: Setup and configuration for SmartInstall is not covered by this manual [Reset] Reset all settings from Professional mode to default values. [Switch on channel] When the TV is switched on it will start up on the specified source/channel. Available EXT1, EXT2, VGA, HDMI, HDMI side, AV side or one of the installed TV channels. [Switch o
Summary of the content on the page No. 19
[Maximum volume] This option specifies the maximum allowable volume level of the TV. Selectable value from 00 until 60. [Switch on picture format] This settings allows you to set a switch on picture format. The power on function allows the TV to enter a specific mode ([On], [Standby], or [Last status]) of operation when the mains power is activated (cold start): [On]: The TV will always turn on (show startup channel) after the mains power is connected. [Standby]: When set
Summary of the content on the page No. 20
When pressing “OK” button on remote control while editing line 1 or 2, a virtual keyboard will pop up on screen. Note: Maximum 20 characters per line. [Line 2] Line 2: Second line of the welcome message. [Clear] Will delete the current welcome message. [Message Time-out] Sets the period of time to display the welcome message on the screen when TV is turned on from standby. Selectable values: 20, 25, 30 seconds. [Display logo] Enables / disables to show the stored we
