Summary of the content on the page No. 1
PROFESSIONAL
SERIES
Remote Start with Keyless Entry
Installation Guide
CA 5550SST
2010 Audiovox Electronics Corporation. All rights reserved. 1
Summary of the content on the page No. 2
Table of Contents Before You Begin ...................................................................................... 3 Wire Connection Guide ........................................................................... 4 7 Pin Main Harness ................................................................................... 5 3 Pin Parking Light Harness ..................................................................... 7 6 Pin Start Harness ...................................................
Summary of the content on the page No. 3
BEFORE YOU BEGIN PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces Avoid mounting components or routing wires near moving parts Tape or loom wires under hood for protection and appearance Use grommets when routing wires through metal surfaces Use a Digital Multi Meter for testing and verifying circuits. DO NOT USE A TEST LIGHT, OR "COMPUTER SA
Summary of the content on the page No. 4
7 Pin Main Harness 3 Pin Parking Light Harness 6 Pin Start Harness 4 Pin Alternate Harness 2 Pin Lock Harness 4 2010 Audiovox Electronics Corporation. All rights reserved.
Summary of the content on the page No. 5
7 Pin Main Harness 1 BLACK/WHITE ILLUMINATED ENTRY OUTPUT ( - ) This wire provides a ( - ) 500mA output for 30 seconds when the system is disarmed capable of driving relays. Locate the vehicle’s dome light or pin switch wire. Verification: This wire will register positive voltage or ground when the vehicle's dome light is turned ON. 2 BROWN/BLACK HORN OUTPUT ( - ) Locate the vehicle’s horn wire. Verification: This wire will register at positive voltage and register ground when the horn switch i
Summary of the content on the page No. 6
Ignition Switch GM VATS Matching Value Resistor 87 BLUE/BLACK ActiveOutput Fused +12 Volt 87a Wire Battery Source 86 85 30 X CUT VATS Control Module Ignition 3 Accessory 2/3 Fused +12 Volt Fused +12 Volt Battery Source Battery Source 87 87 Jump To ORANGE BLUE/BLACK Active Output Jump To PINK BLUE/BLACK Active Output 87a Accessory Output Wire 87a Ignition Output Wire Wire From 86 85 Wire From 86 85 Control Module 30 Control Module 3
Summary of the content on the page No. 7
6 GRAY HOOD PIN INPUT ( - ) Install a Hood Pin Switch and connect to the GRAY wire. This connection is required for Remote Start. Verification: This wire when connected will register ground when the vehicle's hood is opened. Connect the GRAY wire to the hood pin. NOTE: Be sure to loom the wire, and seal the grommet. 7 BROWN/RED BRAKE INPUT ( + ) Locate the vehicle’s brake light wire at the brake pedal mounted switch. Verification: This wire registers positive voltage when the brake pedal is pres
Summary of the content on the page No. 8
6 Pin Start Harness 1 PURPLE STARTER OUTPUT ( + ) Locate the vehicle starter wire. Verification: This wire registers voltage only when the key is turned to the START position. Verification: The starter wire registers voltage when the key is turned to the START position. Connect the PURPLE wire to the vehicle starter wire. 2 RED BATTERY 12V ( + ) Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch. Verification: This wire will register ( + ) voltage in all po
Summary of the content on the page No. 9
5 RED BATTERY 12V ( + ) Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch. Verification: This wire will register ( + ) voltage in all positions of the ignition switch. Connect the RED wire to the constant 12 Volt battery wire. NOTE: Remove all fuses until all connections are made. 6 PINK IGNITION 1 ( + ) Locate the vehicle’s ignition wire at the ignition switch. Verification: This wire registers voltage when the key is turned to the ON (or RUN) position
Summary of the content on the page No. 10
3 GREEN/WHITE FACTORY ARM / PULSE AFTER SHUTDOWN ( - ) This wire will supply a ( - ) 500mA pulse after the remote start shuts down. This is typically used to re-lock the vehicle’s doors if they unlock upon remote start shutdown. It can also be used to pulse a door pin-switch wire to prevent the vehicle’s accessories from remaining on after remote start shutdown. 4 BLACK/YELLOW PULSE DURING CRANK ( - ) Locate the vehicle’s second starter (crank) wire at the ignition switch. (if equipped) V
Summary of the content on the page No. 11
Negative Switching Locks All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch. Verification: These wires will register ground when the Lock and Unlock switches are activated. Connect the GREEN and BLUE wires shown in the diagram below. Negative Locks: GREEN (-) Lock Output Lock Vehicle Door Lock Control Relays Unlock BLUE (-) Unlock Output Positive Switching Locks All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock sw
Summary of the content on the page No. 12
Reverse Polarity Locks (5-Wire Door locks) All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch. Verification: These wires will rest at ground and register positive voltage when the Lock and Unlock switches are activated. Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram below using (2) SPDT relays (not supplied). Reverse Polarity Locks: Fused +12 Volt Battery Souce 87 87a GREEN (-) Lock Output 86 85 30 Lock To Door Lock Motor X Cut Unl
Summary of the content on the page No. 13
Positive Multiplexed Locks All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch. Verification: This wire will show variable positive voltage when the switch is activated. Please consult the wire and location chart for specific resistor values for your vehicle. Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram below using (2) SPDT relays (not supplied). Multiplex Locks: 87 87 Fused +12 Volt 87a GREEN (-) Lock Output 87a BLUE (-) Unlock O
Summary of the content on the page No. 14
Additional Ports Antenna / LED / Programming Port Mount the supplied antenna/receiver to a clear spot on the vehicle's windshield that will not block the driver's vision. A good location is usually high on the windshield near the rear view mirror. Be careful not to mount the antenna/receiver on any metallic window film, as this will effect system range. Route the antenna/ receiver cable to the control module and plug into the antenna port. Data Bus Interface Port This 4 pin port is used for F
Summary of the content on the page No. 15
Set Up & Programming Transmitter Programming - Feature Bank 1 1. Turn the ignition ON. 2. Press and hold the valet/override button. 3. Within 10 seconds the system will chirp (3) three times. 4. Press 1 button of each transmitter you wish to program. 5. The system will respond with 1 chirp for each accepted transmitter. 6. Pressing the override button at anytime during programming will advance to the next bank. NOTE: The system will exit transmitter programming after 15 seconds of inactivity. N
Summary of the content on the page No. 16
Feature Bank 1 - 3 Chirps Transmitter Programming Refer to transmitter programming. 16 2010 Audiovox Electronics Corporation. All rights reserved.
Summary of the content on the page No. 17
Tach Programming The unit will not operate unless a tach signal is programmed or the tachless option is turned ON. If an attempt is made to start the vehicle via the remote start without first programming tach, the unit will flash the parking lights 7 times indicating tach has not been learned and stored. If the tach rate is not properly programmed to the specific vehicle, the unit may not realize that the vehicle is running in certain instances and reengage the starter motor. The Remote Start
Summary of the content on the page No. 18
Feature Descriptions Feature Bank 2 - Security 1 - Silent Choice: Controls the normal arm/disarm chirps of the security system. ON - Silent arming/disarming upon first press of lock/unlock, pressing lock/ unlock a second time will activate the arm/disarm chirps respectively. The system will only sound the arm/disarm chirps upon a second press of the lock/unlock buttons. OFF - normal arm/disarm chirps upon the first press of lock/unlock. Feature Bank 3 - Output Control 1 - Extended Lock Pulse: Co
Summary of the content on the page No. 19
3 - Ignition Controlled Locks: Control of door locks when the ignition is cycled ON or OFF. OFF - Door locks not activated by ignition. Lock and Unlock - Doors lock when ignition is turned on and unlock when ignition is turned off. Lock Only - Doors lock when ignition is turned on only. Unlock Only Doors unlock when ignition is turned off only. 4 - Horn Output Timing: Control the minimum horn pulse time in milli seconds, some vehicle will require a longer pulse to activate the factory horn. 16mS
Summary of the content on the page No. 20
4 - Tach Mode: Determines how the system monitors the engine running during remote start. Tach - Hard wired directly to the tach wire of the vehicle to monitor AC voltage. Tachless (Crank Average/Voltage) - Determines crank time by averaging the last 8 times the vehicle was started with the key and then monitors the change in voltage after remote start. Hybrid (Crank Average / No Voltage) - Determines crank time by averaging the last 8 times the vehicle was started with the key. DBI Port - Monit
