Summary of the content on the page No. 1
High Definition
Television Receiver
OWNER’S MANUAL
MODEL : LST-3100A
Before connecting, operating or adjusting this product,
please read this owner’s manual carefully and completely.
Summary of the content on the page No. 2
Safety Precautions CAUTION: CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE RISK OF ELECTRIC SHOCK COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. DO NOT OPEN REFER TO QUALIFIED SERVICE PERSONNEL. THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE PROD- UCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS. TH
Summary of the content on the page No. 3
IMPORTANT SAFETY INSTRUCTIONS CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS INSTALLATION AND OPERATING GUIDE AND THOSE MARKED ON THE UNIT. RETAIN THIS GUIDE FOR FUTURE REFERENCE. This set has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in this unit will protect you if you observe the following procedures for installation, use, and servicing. This unit does not contain any
Summary of the content on the page No. 4
Table of Contents Introduction NORMAL OPERATION Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . 2 Program and Station Guide . . . . . . . . . . . . . . . 36-37 IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . 3 Normal Operation . . . . . . . . . . . . . . . . . . . . . . . . . 38 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Channel Selection . . . . . . . . . . . . . . . . . . . . . . . 38 Front Panel Controls and Display Window . . . . . . 5 Volu
Summary of the content on the page No. 5
Front Panel Controls and Display Window 3 4 1 2 Arrow Buttons ( / / / ) Allow you to navigate on-screen menus and to adjust the system settings and preferences. Use the arrow keys to move to a menu option and then use the SELECT button to access it. If no menu is displayed, the LEFT/RIGHT arrows control the volume setting and the UP/DOWN arrows select channels. Remote Control Sensor Receives signals from the remote control. Power Turns the HDTV Receiver on or off. Display Window DISPLAY FORMAT
Summary of the content on the page No. 6
Remote Control Key Functions STB Mode Indicator Sets operational mode of remote control to Indicates the remote control operational the HDTV Receiver. mode. STB TV VCR DVD AUX TV/INPUT MODE STB MODE MODE POWER WER To select the TV’s source (Tuner or AUX Selects operational mode of remote control. A/V input). POWER TV/INPUT ez ADD ez ADD Turns the HDTV Receiver ON and OFF. * Automatically adds new channels (digital) This button is not available. AUDIO CC SIGNAL available through the antenna input
Summary of the content on the page No. 7
Unpacking HDTV Receiver and Accessories/Connection Overview Make sure you have received all the accessories listed below with the High Definition Television Receiver. High Definition Television Receiver The HDTV Receiver is capable of receiving signals from cable and/or over-the-air antenna sources and sending the signals to your TV. Included with the Receiver are the following accessories. Audio Cable Video Cable Component(YPbPr) Cable RF Cable Remote Control 2 AA Batteries Audio/Video Jacks a
Summary of the content on the page No. 8
Connection Panel Overview ANT IN Connect to HDTV signal source; external/internal antenna. OPTICAL (Digital audio out jack) Connect to digital (optical) audio equipment. AUTHORIZED SERVICE ONLY Is used only for authorized service purposes. COMPONENT VIDEO OUT Connect to a TV with YPbPr inputs. COAXIAL (Digital audio out jack) Connect to digital (coaxial) audio equipment. VIDEO OUT Connect to a TV with video inputs. AC Power Cord Plug into the power source. DVI OUT Connect to a TV with DVI conn
Summary of the content on the page No. 9
Connections Antenna Connections Connect the “Antenna” to the “ANT IN” jack on the HDTV Receiver using a coaxial RF cable. 1 ote There might be some areas where the signal strength could be too high. If so, you may need to connect the antenna to an attenuator. Screw the attenuator onto the “ANT IN” jack. Connect the “ANT LOOP OUT” jack on the HDTV Receiver to the “Antenna In” jack on your TV using a coaxial 2 RF cable. Antenna Cable TV Wall Jack Panel TV or Other Device Connection Panel ANTEN
Summary of the content on the page No. 10
Connections (Continued) Display Formats Overview • The HDTV Tuner offers various display formats and multiple video outputs. When the HDTV Tuner is connected to A/V systems, the HDTV Tuner can provide video signal formats 1080i, 720p, 480p, and 480i. • 1080i, 720p, 480p, and 480i modes are available for component video (YPbPr) outputs. • 1080i, 720p, and 480p modes are available for RGB and DVI outputs. • 480i mode is available for VIDEO, S-VIDEO, and COMPONENT VIDEO outputs. • The HDTV Tuner ha
Summary of the content on the page No. 11
Connections (Continued) HD Monitor Component (YPbPr) Connections Antenna HD Ready TV Connection Panel Cable TV ANTENNA VIDEO AUDIO INPUT COMPONENT VIDEO INPUT INPUT Wall Jack Panel INPUT Y Pr Pb L R OR To AUDIO OUT HDTV Receiver Connection Panel Connect the “Antenna/Cable” to the “ANT IN” jack on the HDTV Receiver using a coaxial RF cable. 1 ote There might be some areas where the signal strength could be too high. If so, you may need to connect the antenna to an attenuator. Screw the attenuat
Summary of the content on the page No. 12
Connections (Continued) HD Monitor RGB Connections Antenna Cable TV Wall Jack Panel HD Ready TV Connection Panel ANTENNA S-VIDEO VIDEO RGB INPUT AUDIO INPUT INPUT INPUT INPUT L R OR To AUDIO OUT HDTV Receiver Connection Panel 1 Connect the “Antenna/Cable” to the “ANT IN” jack on the HDTV Receiver using a coaxial RF cable. 1 ote There might be some areas where the signal strength could be too high. If so, you may need to connect the antenna to an attenuator. Screw the attenuator onto the “ANT I
Summary of the content on the page No. 13
Connections (Continued) HD Monitor DVI-HDTV Connections Antenna Cable TV Wall Jack Panel HD Ready TV Connection Panel ANTENNA S-VIDEO VIDEO AUDIO INPUT DVI-HDTV INPUT INPUT INPUT INPUT R L OR To AUDIO OUT HDTV Receiver Connection Panel 1 Connect the “Antenna/Cable” to the “ANT IN” jack on the HDTV Receiver using a coaxial RF cable. 1 ote There might be some areas where the signal strength could be too high. If so, you may need to connect the antenna to an attenuator. Screw the attenuator onto
Summary of the content on the page No. 14
Connections (Continued) VCR Connections VCR Connection Panel VIDEO AUDIO INPUT INPUT R L L To AUDIO OUT HDTV Receiver Connection Panel Connect the L/R “AUDIO OUT” jacks and “VIDEO OUT” jack on the HDTV Receiver to the “A/V in” jacks on your VCR using RCA-type cables. (If your VCR is equipped with an S-Video jack, use the “S-Video” jack.) Caution If 480i display format is selected, the VCR will record an onscreen display onto the tape during recording if: the channel is changed with CH (+/–) the
Summary of the content on the page No. 15
Connections (Continued) Amplifier (Receiver) Connections Amplifier (Receiver) Connection Panel OPTICAL COAXIAL R L DIGITAL INPUT AUDIO INPUT OR HDTV Receiver Connection Panel Connecting to an amplifier equipped with two channel analog stereo or Dolby Surround Connect the Left and Right AUDIO OUT jacks on the HDTV Receiver to the audio left and right in jacks on your amplifier, receiver, or stereo system, using the supplied audio cables. Connecting to an amplifier equipped with two channel digita
Summary of the content on the page No. 16
Setting the Display Format The HDTV Receiver provides several display formats. The DISPLAY FOR- MAT button on the front panel changes the output connector and resolution. The output resolution may be converted from the original broadcast format. Display Format Setting Press DISPLAY FORMAT once on the front panel. 1 The current output signal will appear in the display window. Depending on the type of monitor that the HDTV Receiver is con- 2 nected to, press DISPLAY FORMAT repeatedly on the front
Summary of the content on the page No. 17
Initial Settings In this menu system, there are several ways to customize the settings pro- vided. Most menus consist of three levels to set up the options, but some require greater depth for the variety of settings. If you press the MENU but- ton, only the first and second level of the menu system will appear on the TV screen. The third level can be displayed by pressing (SELECT). If a menu has more than three levels, the pop-up dialogue box will be displayed as the fourth or fifth level. For n
Summary of the content on the page No. 18
Setup Menu Options EZ Scan (Channel Search) Automatically finds all channels (digital) available using the ‘Ant In’ source, and stores all the active channels found on the channel list. Inactive or weak channels may not appear on the list. In that case, add missing channels manually with the Manual Add menu. The channel list created here can be seen in the Ch. Edit menu. Press MENU to display the on-screen menu. 1 Select the SETUP menu using 3 / 4 then press (SELECT) or 2 to 2 move to the secon
Summary of the content on the page No. 19
Setup Menu Options (Continued) Ch. Edit (Channel Edit) Channel Edit allows you to add or delete channels from the channel list in memory manually and create your own surf list of favorite channels. Press SURF ( ) on the remote control when a channel is highlighted. Press MENU to display the on-screen menu. 1 Select the SETUP menu using 3 / 4 then press (SELECT) or 2 to 2 move to the second level. Select the Ch. Edit using 3 / 4 then press (SELECT) or 2. 3 Channel Edit menu appears. To move one
Summary of the content on the page No. 20
Setup Menu Options (Continued) Manual Channel Add/Delete This feature allows you to add or delete channels manually while monitoring signal strength. Press MENU to display the on-screen menu. 1 3 4 2 Select the SETUP menu using / then press (SELECT) or to 2 move to the second level. Select the Manual Add using 3 / 4 then press (SELECT) or 2. 3 Manual Add menu appears. Select a channel to add or delete using 3 / 4 or the numbered but- 4 tons with the Manual Add menu. Press (SELECT) to confirm y
