Summary of the content on the page No. 1
INTELLIGENT
Power Supply / Charger
OWNERS MANUAL
KIPS12-45
KIPS12-60
KIPS12-80
Computer Controlled Charging System
The Intelligent way to charge and maintain your vehicle’s battery.
45 AMP • 60 AMP • 80 AMP
Constantly monitors the battery voltage and automatically
selects one of four operating modes:
NORMAL • BOOST • STORAGE • DESULFATION
Summary of the content on the page No. 2
FEATURES INTELLIGENT CHARGING The Kinetik Intelligent Power Converter is the intelligent way to charge your Kinetik battery. The built-in microprocessor constantly monitors the battery voltage then automatically adjusts the converter output voltage to provide the proper charging voltage for fast recharges and long-term maintenance. MULTIPLE BATTERY CHARGING Kinetik Intelligent Power Converters have the capability of charging multiple batteries at the same time! They can even charge a combi
Summary of the content on the page No. 3
GENERAL INFORMATION Kinetik Intelligent 120 VAC to 12 VDC Power Converters are state-of-the-art electronic converters / battery chargers. Their compact size and quiet operation gives greater flexibility in selecting the mounting locaiton for either OEM installa- tion or after market replacement. The Kinetik Intelligent Power Converters have a computer controlled charging module built in. This is a microprocessor-controlled device which constantly monitors the battery, and then automaticall
Summary of the content on the page No. 4
GENERAL INFORMATION (continued...) 14.4 Volts (Boost Mode) Returned the battery to 90% of full charge in approximately 8 hours. The battery reached full charge in approximately 11 hours. 13.6 Volts (Normal Mode) Required 40 hours to return the battery to 90% of full charge and 78 hours to reach full charge. 13.2 Volts (Storage Mode) Required 60 hours to return the battery to 90% of full charge and 100 hours to reach full charge. The integrated intelligent microprocessors ability to change th
Summary of the content on the page No. 5
INSTALLATION INSTRUCTIONS Horizontal mounting of the Kinetik Intelligent Power Converter is recommended although it can be mounted in any position that provides unobstructed ventilation to the fan and vent holes. Secure the converter firmly to the mounting surface using standard fasteners. The installer should test the converter under full load conditions in its intended mounting location. This will insure that there is sufficient unobstructed ventila- tion to the converter allowing it to
Summary of the content on the page No. 6
TROUBLE SHOOTING GUIDE PROBLEM POSSIBLE CAUSES ACTION 1. No Output 120 VAC supply not con- Connect power supply nected Check AC distribution panel for proper operation External Fuses Blown Check for Reverse Polarity Replace Fuses with same type and rating Short Circuit Trace Circuits for possible fault Unit has shutdown due Check air flow to overheating Allow unit to cool Unit has shutdown due Check input voltage to over voltage (Also see Converter will shut down if item 5 below) the input
Summary of the content on the page No. 7
INPUT/OUTPUT SPECIFICATIONS KINETIK KIPS12-45 KINETIK KIPS12-60 Input: 105-130 VAC 60 Hz 725 Watts Input: 105-130 VAC 60 Hz 1000 Watts Output: 13.6 VDC, 45 Amps Output: 13.6 VDC, 60 Amps Dimensions: 4.5H x 8.625L x 7.25W Dimensions: 3.6H x 9.15L x 9W Weight: 4.5lbs Weight: 5.8lbs KINETIK KIPS12-80 Input: 105-130 VAC 60 Hz 1300 Watts Output: 13.6 VDC, 80 Amps Dimensions: 3.6H x 11.65L x 9W Weight: 7.5lbs CAUTION RISK OF FIRE: Chassis bonding wire must be a separate wire ran directly from the Gro
Summary of the content on the page No. 8
KINETIK POWER CONVERTER LIMITED WARRANTY I. LIMITED WARRANTY: Kinetik warrants its power converter to be free from defects in material or workmanship under normal use and service; and limits the repair or replacment. II. DURATION: This warranty shall extend for a period of one year from the original date of purchase, and is only valid within the continental limits of the United States and Canada. III. WARRANTY EXCLUSIONS: This warranty specifically does not apply to: A. Any power converter
