Summary of the content on the page No. 1
Serial I/O SST16P DB and RJ Adapter
37L1415 and 37L1423
Installation Guide
OPTIONS
by IBM
37L1477
560155/A
October 1998
560155_A.p65 1 11/25/98, 6:56 PM
Summary of the content on the page No. 2
Overview IBM Serial I/O Adapters are intelligent, high-speed (up to 230.4 kbps on each port) Multiport Boards providing high performance serial I/O solutions for PCI bus systems. All port interfaces are standard RS-232 with full modem control and voltage surge protection on every pin. IBM Serial I/O Adapters appear to the system host processor as memory. That is, they are memory mapped devices. Each Adapter is automatically mapped into system memory at the time of device driver installation.
Summary of the content on the page No. 3
Installation Note: Please refer to the user manual that came with your personal computer for detailed installation instructions. Use the following procedure to install your Serial I/O Adapter Card: 1. Set the host computer system power switch to OFF and disconnect the power cord. 2. Locate a free PCI expansion slot. 3. Insert and secure the board firmly into the expansion slot. 4. Connect the Host SSP-16 (37L1476) cable between the SST- 16P board and the Connector Panel (see Figure 1). 5. Replac
Summary of the content on the page No. 4
Connector Panels (continued) Figure 2. SST-16P (37L1423) and SST-16P (37L1415) Connector Panels Figure 3. SST-16P Connector Panel Pin-outs Figure 4. SST-16P RJ Connector Panel Pin-outs IBM Serial I/O SST-16P Installation Guide 4 560155_A.p65 4 11/25/98, 6:56 PM
Summary of the content on the page No. 5
Port to Device Cabling The following six figures show how to pin-out your own cables to go between CP-16 Connector Panel (CP) ports and your Terminals, Printers, Modems, etc. DB Connector Panel to Device Cabling Figures 5 through 7 show the pin-outs required to make a cable to go between DB-25 ports and your Terminals, Printers, Modems, etc. Figure 5. Cable Pin-Outs for CP DB-25 to Terminal/Printer DB-25 Figure 6. Cable Pin-Outs CP DB-25 to PC DB-9 IBM Serial I/O SST-16P Installation Guide 5
Summary of the content on the page No. 6
DB-25 Connector Panel to Device Cabling (continued) Figure 7. Cable Pin-Outs for CP DB-25 to Modem DB-25 RJ-45 Connector Panel to Device Cabling Figures 8 through 10 show the pin-outs required to make a cable to go between CP16 RJ-45 CP ports and your terminals, printers, modems, etc. Figure 8. Cable Pin-Outs for CP-16 RJ-45 to Terminal/ Printer DB-25 IBM Serial I/O SST-16P Installation Guide 6 560155_A.p65 6 11/25/98, 6:56 PM
Summary of the content on the page No. 7
RJ-45 Connector Panel to Device Cabling (continued) Figure 9. Cable Pin-Outs for CP-16 RJ-45 to PC (DB-9) Figure 10. Cable Pin-Outs for CP-16 RJ-45 to Modem DB-25 IBM Serial I/O SST-16P Installation Guide 7 560155_A.p65 7 11/25/98, 6:56 PM
Summary of the content on the page No. 8
Help and Service Information Before calling, please prepare for your call by following these steps: Preparing for the Call To assist the technical support representative, have available as much of the following information as possible: • Computer manufacturer and computer model. • Options part number (Table 1). • Options part name (Table 1). • Serial number (if available). • Proof of purchase (including date and place). • Exact wording of the error message (if any) • Description of the problem •
Summary of the content on the page No. 9
IBM OPTIONS IBM Part PCI Serial I/O Adapters Number 3r 7L1414 Serial I/O SST8P DB Adapte 3r 7L1415 Serial I/O SST16P RJ Adapte 3r 7L1423 Serial I/O SST16P DB Adapte 3r 7L1416 Serial I/O SST128 Expandable Adapte 3e 7L1417 Serial I/O PM16RJ Port Modul 3e 7L1418 Serial I/O PM16DB Port Modul 3y 7L1421 Serial I/O PS4 Power Suppl 3y 7L1422 Serial I/O PS4 WT Power Suppl 3t 7L1419 Serial I/O 16RJ Multiplexer Se 3t 7L1420 Serial I/O 16DB Multiplexer Se 3t 7L1424 Serial I/O 16RJ WT Multiplexer Se 3t 7L142
Summary of the content on the page No. 10
Product Warranty The following warranty information applies to products purchased in the United States, Canada, and Puerto Rico. For warranty terms and conditions for products purchased in other countries, see the enclosed Warranty insert, or contact your IBM reseller or IBM marketing representative. International Business Machines Corporation Armonk, New York, 10504 Statement of Limited Warranty The warranties provided by IBM in this Statement of Limited War- ranty apply only to Machines you o
Summary of the content on the page No. 11
1) for certain Machines, the designated, serial-numbered Machine and 2) at an engineering-change level compatible with the feature, conversion, or upgrade. Many of these transactions involve the removal of parts and their return to IBM. You represent that all removed parts are genuine and unaltered. A part that replaces a removed part will assume the warranty service status of the replaced part. If a Machine does not function as warranted during the warranty period, IBM or your reseller will rep
Summary of the content on the page No. 12
least functionally equivalent to the item replaced. The replacement assumes the warranty service status of the replaced item. Before IBM or your reseller exchanges a Machine or part, you agree to remove all features, parts, options, alterations, and attachments not under warranty service. You also agree to ensure that the Machine is free of any legal obligations or restrictions that prevent its exchange. You agree to: 1. obtain authorization from the owner to have IBM or your reseller service a
Summary of the content on the page No. 13
Limitation of Liability Circumstances may arise where, because of a default on IBM’s part or other liability you are entitled to recover damages from IBM. In each such instance, regardless of the basis on which you are entitled to claim damages from IBM (including fundamental breach, negligence, misrepresentation, or other contract or tort claim), IBM is liable only for: 1. damages for bodily injury (including death) and damage to real property and tangible personal property; and 2. the amount o
Summary of the content on the page No. 14
Electronic Emission Notices Federal Communications Commission (FCC) Statement Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instr
Summary of the content on the page No. 15
IBM Serial I/O SST-16P Installation Guide 15 560155_A.p65 15 11/25/98, 6:56 PM
Summary of the content on the page No. 16
IBM Serial I/O SST-16P Installation Guide 16 560155_A.p65 16 11/25/98, 6:56 PM
Summary of the content on the page No. 17
IBM Serial I/O SST-16P Installation Guide 17 560155_A.p65 17 11/25/98, 6:56 PM
Summary of the content on the page No. 18
© 1998 IBM. All rights reserved. Reproduction without permission prohibited. IBM makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Information is subject to change without notice and does not represent a commitment on the part of IBM. IBM Serial I/O SST-16P Installation Guide 18 560155_A.p65 18 11/25/98, 6:56 PM
