Summary of the content on the page No. 1
LT-17S2
LT-23S2
WIDE LCD PANEL TV INSTRUCTIONS
1
5030057088
Summary of the content on the page No. 2
Thank you for buying this JVC WIDE LCD PANEL TV To make sure you understand how to use your new TV, please read this manual thoroughly before you begin. (“LCD” stands for Liquid Crystal Display.) WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING Always use the provided AC adapter and power cord. WARNING • Fingers may be trapped under the TV causing injuries. Hold the TV at the bottom in the middle, and do not allow it to tilt up or down. • The
Summary of the content on the page No. 3
Point defects LCDs use collections of fine pixels to display images. While there is no problem with more than 99.99% of these pixels, please understand that a very small number of pixels may not light or may light all the time. Distance recommendations Avoid improper installation and never position the unit where good ventilation is impossible. 200 mm 200 mm 150 mm 150 mm When installing this TV, distance recommendations must be maintained between the set and the wall, as well as inside a tig
Summary of the content on the page No. 4
LT-26C31BUE/SUE/BJE/SJE / LCT1484-001A-U / English (EK) LT-26C31BUE(EK)_Eng.book Page 3 Tuesday, August 5, 2003 2:18 PM CONTENTS Setting up your TV..................................4 SOUND ................................................. 19 Installation..........................................................4 Sound Adjustment........................................... 19 Using the stand ..................................................4 HYPER SOUND ....................................
Summary of the content on the page No. 5
Setting up your TV Installation Cautions for installation • Install the TV in a corner on a wall or on the floor so as to keep cords out of the way. • The TV will generate a slight amount of heat during operation. Ensure that sufficient space is available around the TV to allow satisfactory cooling. See “Distance recommendations” on page 2. Using the stand This TV comes with a Table Top Stand already Cable holder attached. A cable holder which is used to keep the connection cables This stand
Summary of the content on the page No. 6
LT-26C31BUE/SUE/BJE/SJE / LCT1484-001A-U / English (EK) LT-26C31BUE(EK)_Eng.book Page 5 Tuesday, August 5, 2003 2:18 PM Setting up your TV Putting the batteries into the Remote control Use two AA/R6 dry cell batteries. Insert the batteries from the - end, making sure the + and - polarities are correct. • Follow the warnings printed on the batteries. • Battery life is about six months to one year, depending on your frequency of use. • The batteries we supply are only for setting up and testin
Summary of the content on the page No. 7
Setting up your TV Connecting the aerial and video Connecting the power cord to the AC cassette recorder (VCR) outlet • Aerial cable is not supplied. Use a good quality 75-ohm If you are connecting a AC adapter, follow coaxial cable. • Read the manual that came with the VCR before in the diagram below. connecting. • Connect to the TV and to the AC outlet. If not connecting a VCR (follow 11): Connect an aerial cable to the aerial socket on Caution this TV. • Operate only from the po
Summary of the content on the page No. 8
Initial settings When the TV is first turned on, it enters the initial setting 3 AUTO PROGRAM menu appears. mode. Follow the instructions on the on-screen display to make the initial settings. INSTALL LANGUAGE ENGLISH AUTO PROGRAM VCR/TV/DVD : SELECT :MOVE Switch 4 Press the buttons to choose the / Yellow button LANGUAGE. Blue button 5 Press the buttons to choose the ENGLISH. OK The on-screen display will then be in English. BACK 6 P ress the buttons to choose the
Summary of the content on the page No. 9
Initial settings Now, the initial settings are complete, and you can watch the TV • If your TV can detect the TV channel name from the TV channel broadcast signal, the TV channel name is assigned to the programme number to which the TV channel has been set. However, which TV channels are set to which programme numbers will depend on the area in which you live. • If a TV channel you want to view is not set to a programme number, you can set it using the MANUAL function. For details, see “
Summary of the content on the page No. 10
LT-26C31BUE/SUE/BJE/SJE / LCT1484-001A-U / English (EK) LT-26C31BUE(EK)_Eng.book Page 9 Tuesday, August 5, 2003 2:18 PM TV buttons and functions Turn the TV on from standby mode 1 Press the button or P / buttons to turn the TV on from standby mode • Check that the AC plug on the power cord from the TV is connected to correctly AC outlet. Choose a TV channel Press the P / buttons to choose a programme number or an EXT terminal Watch images from external devices 2 Press the TV/AV button to
Summary of the content on the page No. 11
Remote control buttons and functions 1 Muting button 2 Number buttons 3 Information button 4 ZOOM button 5 button 6 button 7 / buttons 8 (Text) button 9 P buttons / 10 VCR/DVD/Teletext control buttons / 11 buttons button 12 13 button 14 Standby button VCR/TV/DVD switch 15 button 16 AV 17 button 18 Picture button 19 Color buttons 20 MENU button 21 OK button 22 / buttons BACK button 23 24 buttons 25 button 26 button Choose a TV channel Use the number buttons: Enter the programme n
Summary of the content on the page No. 12
Remote control buttons and functions Adjust the volume Displaying the source information You can display the source information and current time on Press the buttons to adjust the volume. The volume indicator appears and the volume changes as the screen. you press the buttons. Press the i (information) button to display the Muting the sound source information. Press the (muting) button to turn off the i (information) button changes the display as Pressing the sound. follows: Pressing t
Summary of the content on the page No. 13
Remote control buttons and functions Choose the ZOOM mode ZOOM function 1Press the ZOOM button to display the ZOOM You can change the screen size according to the picture menu aspect ratio. Choose the optimum one from the following • The button does not work in the twin ZOOM ZOOM modes. pictures mode. AUTO: When a WSS (Wide Screen Signalling) signal, which shows Adjusting the visible area of the picture the aspect ratio of the picture, is included in the broadcast If subtitles or the top
Summary of the content on the page No. 14
Remote control buttons and functions Sleep timer function Using the PCPIP function The Sleep Timer can turn the TV off for you after you fall A PC picture and TV or a video programme from an asleep. Programme it to work in intervals of 10 minutes, for external device can be watched at the same time. a total time of up to 120 minutes. Press the button. 1Press he button. t SLEEP TIMER OFF Picture in picture mode Main- Sub- 10 picture picture 20 30 100 SLEEP TIME
Summary of the content on the page No. 15
Remote control buttons and functions Operating a JVC brand VCR or DVD player • If the main-picture signal is poor, the quality of the These buttons will operate a JVC brand VCR or DVD sub-picture may also be poor. player. Pressing a button that looks the same as the device’s • If the pictures have different standards, the top and original remote control button has the same effect as the bottom of one of them may be missing. original remote control. • If you press the menu button when the P
Summary of the content on the page No. 16
Teletext function Hold Basic operation You can hold a teletext page on the screen for as long as you want, even while several other teletext pages are being 1 Choose a TV channel with a teletext broadcast received. 2 Make sure to set the VCR/TV/DVD switch to the Press the (Hold) button TV position. Hold indication To cancel the Hold function: Press (Hold) button again. 3 Press (Text) button to display the teletext Pressing (Text) button changes the mode as follows: TV mode TEXT--- TEXT--
Summary of the content on the page No. 17
Teletext function Sub-page Cancel Some teletext pages include sub-pages that are You can search for a teletext page while watching TV. automatically displayed. 1 Press the number button to enter a page 1 Choose a teletext page that includes sub-pages number, or press a colour button Press the button, Sub-page numbers can be viewed The TV searches for a teletext page. and displayed at the screen. 2 Press the (Cancel) button 2 Press the number buttons to choose a sub-page The TV programme
Summary of the content on the page No. 18
LT-26C31BUE/SUE/BJE/SJE / LCT1484-001A-U / English (EK) LT-26C31BUE(EK)_Eng.book Page 17 Tuesday, August 5, 2003 2:18 PM Using the TV’s menu This TV has a number of functions you can operate using 3 Press the buttons to choose a function / menus. To use all your TV’s functions, you need to • For details of the functions in the menus, see the understand the basic menu operating techniques fully. following pages. / 4 Pres s the buttons to choose the setting of that function • If y
Summary of the content on the page No. 19
PICTURE SETTING Refer to “Using the TV’s menu” (see page 17) for details of WHITE BALANCE displaying the menu. PICTURE You can select one of three WHITE BALANCE modes (three PICTURE MODE BRIGHT tones of white) to adjust the white balance of the picture. CONTRAST Since white is the colour which is used as a reference for all BRIGHT-1 the other colours, changing the WHITE BALANCE mode SHARP CO
Summary of the content on the page No. 20
LT-26C31BUE/SUE/BJE/SJE / LCT1484-001A-U / English (EK) LT-26C31BUE(EK)_Eng.book Page 21 Tuesday, August 5, 2003 2:18 PM SOUND Refer to “Using the TV’s menu” (see page 17) for details of HYPER SOUND displaying the menu. You can enjoy Surround sound with a “live” effect by using SOUND the function. HYPER SOUND BASS ON: TREBLE function is turned on. HYPER SOUND BALANCE HYPER SOUND O
