Summary of the content on the page No. 1
LCD TV RECEIVER
USER'S MANUAL
MODEL: L20AV6-A0
Please read this manual carefully before
using your television and keep this manual
in a good place for future reference.
Summary of the content on the page No. 2
Content Before operation 2 Warnings and Cautions 3 Safety Precautions 5 Preparation for the Remote Control Keys and Ports 6 Front panel 6 Back panel 6 Keys of remote control 7 Basic operation 8 Power on/off and menu operation 9 Viewing TV Programs Tuning 10 Auto search 10 Manual search 11 Fine tune 12 13 Skip 14 Ajusting the Picture and the Sound 14 Multiple picture modes Multiple sound modes 15 Setting function 16 Setting OSD Language 16
Summary of the content on the page No. 3
Warning and Cautions WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. FOR ANY PROBLEM, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. THERE IS A LIGHTNING ARROW SYMBOL IN THE TRIANGLE: THIS SYMBOL INDICATES HIGH VOLTAGE IS PRESENT INSIDE. IT IS DANGEROUS TO MAKE ANY KIND OF CONTACT WITH ANY INSIDE PART OF THIS PRODUCT. THERE IS AN EXCLAMATION MARK IN THE TRIANGLE: THIS SYMBOL ALERTS
Summary of the content on the page No. 4
Safety Precautions To avoid fire hazards, do not use this The product should be tightly fixed to product under direct sunlight or closely avoid drop damages and even fire. to heat sources. Do not locate the product close to water Unplug the power supply and antenna of or oil, which may cause fire hazards. the product when there is a rainstorm, especially thunderstorm. Do not use damaged or worn electric Do not connect excessive sockets in plugs, and keep electric cord away from parallel
Summary of the content on the page No. 5
Safety Precautions (continued) Don't use or store inflammable Don't place the product in a humid area to avoid materials near the product to avoid fire hazards. explosion or fire hazards. Never touch the plug when your hand is wet The antenna of the product should as this might cause electric shocks. be away from electric cable to avoid electric shocks. When antenna is used, measures should be Always make sure that the television taken to prevent water from flowing down along is wel
Summary of the content on the page No. 6
Preparation for the Remote Control Battery loading 1.Slide open the cover of the battery compartment on the back of the remote controller. 2.Load two 5# alkaline batteries in the compartment. (plus and minus poles to respective mark) 3.Replace the cover of the battery compartment. As strong light may interfere the Make sure that there is no signals, change your position to obstacle between the remote operate the remote controller if controller and television set. the television cannot be
Summary of the content on the page No. 7
Keys and Ports Front panel 1 2 3 4 5 7 6 1 MENU: menu display/enter the sub-menu/confirm the adjustment. 2 V-/V+ volume adjustment and adjust the parameters in the menu. 3 P-/P+ program minus and plus, select the menu options 4 TV/AV all input source select:PC-RGB/COMPONENT/AV/S-VIDEO/ TV/exit the menu . 5 POWER: press to be on /standby mode. 6 Power indicator 7 Remote control signal receiver window. Back panel 1 Connect antenna or CATV 75 coaxial cable to receive TV/ CATV signal.
Summary of the content on the page No. 8
Keys of remote control Buttons and Descriptions 1.Press to turn on the TV from standby mode. Press again to switch off the TV to standby mode. 2. MENU Press to display menu or enter the sub-menu MENU C H + 3.CH+/- 2 1 Select the option up and down in menu or select channels when there is no OSD. VOL- VOL+ 4 4. VOL+/- 3 Left and right orientation in menu option CH- or adjust the volume when there is no OSD. 3 1 2 5.Number key: Press to select the channe
Summary of the content on the page No. 9
Power on/off and menu operation Below are methods on how to power on/off the TV set with the switches on the TV and on the remote control. Power on/off Power on/off 1 Connect AC-DC adaptor and power supply wire first, then plug insert the power socket on the wall, the indicator light. 2 If the television is on standby mode , you could press POWER ( ) button on remote control or on the TV to turn on the TV. If you want to switch off the TV to standby mode press POWER button on TV o
Summary of the content on the page No. 10
Viewing TV Programs There are 200 channels from 0 to 199. How to select program Use the direct-digit choosing button 1 3 2 Press the button from 0-9 to select a one digit channel. 6 5 4 Press the button from 0-9 to select a two digits channel. Press the button from 0-9 to select a three digits channel. 8 9 7 Note: when you select one or two digits channel, you should await about 2 seconds to the channel. 0 2 Use CH+/- button Direct-digit Choosing Button Press CH+ to increase the channel positi
Summary of the content on the page No. 11
Tuning There are three ways of searching: automatic search, manual search and MFT (manual fine tune). You may operate it either on the TV or on the remote control. Here is mainly about the remote control. Auto search AUTO SEARCH MENU 1.Press MENU button and CH+/- to select TV SETTING (note: TV SETTING is only available in TV) IMAGE SETTING CH+ TV SETTING 2.Press MENU button to VIDEO ADVANCE enter the TV SETTING and OSD SETTING VOL- VOL+ CH+/- to
Summary of the content on the page No. 12
TUNING (Continued) Manual search MENU Manual search Press CH+/- button or the Direct-digit Choosing button to select a channel directly CH+ IMAGE SETTING 1.Press MENU button and TV SETTING CH+/- to select TV SETTING VOL- VOL+ VIDEO ADVANCE OSD SETTING SOUND SETTING CH- RESET INPUT SOURCE 720 576 50HZ 2.Press MENU button to enter the TV SETTING and CH+/- to select MANUAL CHANNEL 4 SEARCH 3 1 2 S
Summary of the content on the page No. 13
TUNING (Continued) Fine tune When you can't get a satisfactory picture and audio effect, CH+ you can fine tune to obtain. Auto fine VOL- VOL+ 1.Press CH+/- or digit IMAGE SETTING buttons to select the TV SETTING CH- channel, press MENU button VIDEO ADVANCE and CH+/- to select OSD SETTING TV SETTING SOUND SETTING RESET 1 3 2 INPUT SOURCE 720 576 50HZ Press MENU button to 6 5 4 enter the TV SETTING and CH+/- to select AUTO FINE 9 8 7
Summary of the content on the page No. 14
TUNING (Continued) Skip Skip After the programs are preset, you can skip some 1 3 2 programs so that to select your favorite channels only. IMAGE SETTING 1 Press CH+/- or digit 6 5 4 buttons to select the TV SETTING channel you want to skip. 8 9 VIDEO ADVANCE 7 OSD SETTING 2 Press MENU and CH+/- to SOUND SETTING 0 select TV SETTING,then RESET press MENU to enter INPUT SOURCE the sub-menu 720 576 50HZ Direct-digit Choosing Button 3 Press CH+/- to select CHANNEL
Summary of the content on the page No. 15
Adjusting the Picture and the Sound Multiple picture modes How to select the picture mode You may select the mode you want from the MILD three preset modes and one individual mode. NATURE Press the P. STD button to select a mode P.STD VIVID you like. MILD, NATURE, VIVID and USER totally four picture modes can be selected USER alternately. MODE PICTURE QUALITY MILD LOW COLOR AND BRIGHTNESS NATURE MEDIUM COLOR AND BRIGHTNESS VIVID BRIGHT COLOR USER SET BY YOURSELF Set the par
Summary of the content on the page No. 16
Adjusting the Picture and the Sound Multiple sound modes How to select the sound mode NEWS You can quickly select your most favored sound mode from the following four kinds of modes. NATURE S.STD Press the S.STD button to select the THEATER sound quality that you want.NEWS/ NATURE/ THEATER/ USER can be USER selected in turn(their parameter may be adjusted due to your need). Setting the sound This function can let you regulate the volume to the preconcerted parameter quickly 1 Press
Summary of the content on the page No. 17
Setting function Setting function Setting OSD Language 1 Press MENU button and IMAGE SETTING MENU CH+/- to select OSD TV SETTING SETTING,then press VIDEO ADVANCE OSD SETTING MENU button to enter SOUND SETTING CH+ RESET 2 Press CH+/- to select INPUT SOURCE LANGUAGE. 720 576 50HZ VOL- VOL+ LANGUAGE ENGLISH OSD.H CH- 50 OSD.V 50 3 Press MENU button to confirm and VOL+/- button to select the language. Setting OSD position IMA
Summary of the content on the page No. 18
Setting function(continued) ·½±ãµÄͼÏñºÍÉùÒôµ÷Õû¹¦ÄÜ£¨½ÓÉÏÒ³£© Video advance,reset and source input Blue screen 1 Press MENU button and IMAGE SETTING then CH+/- to select MENU TV SETTING VIDEO ADVANCE, then press VIDEO ADVANCE MENU button to enter OSD SETTING SOUND SETTING CH+ RESET 2 Press CH+/- to select INPUT SOURCE 720 576 50HZ BLUE SCREEN. VOL- VOL+ 3 Press MENU button to confirm, then press VOL+/- to select BLUE SCREEN ON CH-
Summary of the content on the page No. 19
PC Mode Function PC mode function Image adjustment You can adjust the contrast, brightness and the position of the image. MENU 1 Press TV/AV to select PC-RGB. CONTRAST 2 Press MENU and CH+/- to BRIGHTNESS CH+ select the option you want to adjust. IMAGE SETTING COLOR SETTING 3 Press MENU to confirm and VOL+/- to adjust. VOL- VOL+ OSD SETTING SOUND SETTING Main menu RESET INPUT SOURCE CONTRAST To adjust the CH- 1024X768 60HZ contrast
Summary of the content on the page No. 20
Connection Connecting additional equipments You can connect the DVD,VCR to the set to enjoy a higher quality of picture . Signal flow DVD,VCD or other units To video/RGB input To audio input To component input AC-DC Laser DVD with output terminal adapter To power socket Note: Please do not use the S-VIDEO and AV terminals simultaneously. Headphone port Plug the headphone in the television headphone port, then the television program sound will be heard from the headphone, not by the televisio
