Summary of the content on the page No. 1
LED LCD TV RECEIVER
USER MANUAL
MODEL:
Please read this manual carefully before using
LET26C430
your television and keep this manual in a good
LET32C430
place for future reference.
Summary of the content on the page No. 2
Rear AV connections
Summary of the content on the page No. 3
Thanks for buying this 26"/ 32" LED LCD TV. This guide will help you set up and begin using your TV. 26" Full HD 1080P Digital LED LCD TV 32" HD Ready LED LCD TV Remote control Remote control AAA battery x2 AAA battery x2 Instruction Manual Instruction Manual Quick start guide Quick start guide Scart cable x1 Scart cable x1 Adaptor Adaptor P . 0 2
Summary of the content on the page No. 4
SAF ETY NOTICE " For your protection,please read these instruction completely and keep this manual for future reference. " Please ensure that the set has adequate ventilation. " Do not place the set near a heat source or in direct sunlight. " Do not put the unit near water or oil as it may cause a fire. " During thunderstorms, unplug both the antenna and power plug to prevent damage. " Do not use a damaged power plug or put the power supply near a heat source as it may cause electric sho
Summary of the content on the page No. 5
WARNINGS AND CAUTIONS Warning Caution High voltages are used in the operation Do not trap the power supply cord under of this television receiver. Do not remove the television receiver. the cabinet back from your set. Refer servicing to qualified service personnel. Caution Never stand on, lean on, or suddenly push Warning the television or
Summary of the content on the page No. 6
02 Introduction INSTALLATION CAUTION *Locate the TV in the room where light Never tamper with any components inside does not strike the screen directly. the TV, or any other adjustment controls not mentioned in this manual. All LED-TVs *Total darkness or a reflection on the are high voltage instruments. When you picture screen can cause eyestrain. Soft clean up dust or water drops on the LED and indirect lighting is recommended for PANEL or CABINET, the power cord should comfortable v
Summary of the content on the page No. 7
PC PRESET MODE V.Freq.(Hz) H.Freq.(KHz) RESOLUTION 1 800*600 60 37.88 2 640*480 60 31.47 3 1024*768 60 48.36 4 1360x768 60 47.7 5 1280x1024 60 63.98 1920x1080 6 60 66.64 (Only for 26") P . 0 6 02 Introduction
Summary of the content on the page No. 8
STAND INSTALLATION GUIDE This STAND INSTALLATION GUIDE is provided to help you easily install the stand. Please carefully follow step 1 through Step 2. Open the box and find the parts 1 Open the box and find the following parts. Screws - Stand x1 pc Packing - Screws x 4 pcs Stand TV Stand Packing Place the stand on the TV 2 1. Insert the stand support pillar into the 2. Insert the stand Ass'y into back cover stand as the arrow indicated direction, as the arrow indicated direction, and t
Summary of the content on the page No. 9
WALL MOUNTING INSTALLATION GUIDELINES Wall Mounting Holes Spacing and Location 200.00 4 Wall mount M4 Screws 1.Use the screwdriver to remove 1 screws from the screw location. 2.Remove the base stand from the Main body. P . 0 8 100.00 02 Introduction
Summary of the content on the page No. 10
Front control panel SOURCE MENU CH+ CH- 3 VOL+ VOL- 1 STANDBY 2 1 SOURCE Display the input source menu. 1 Remote control sensor. 2 Display main MENU. MENU 2 Indicator LED: 3 In TV mode,press CH+ or CH- to change CH+/CH- the channel up and down. Blue:POWER ON. RED STAND BY. In MENU, press CH+ or CH- to select items . 3 Key board. In standby mode, it can Turn on the TV. 4 VOL+/VOL- Adjust sound level. In MENU,adjust the item that you Selected. 5 STANDBY Rear/Side Sockets A AV V
Summary of the content on the page No. 11
P . 1 0 02 Introduction
Summary of the content on the page No. 12
COMMON INTERFACE The common interface (CI) slot is designed to accept the conditional Access (CA) Module and Smart card in order to view the pay TV programmes and additional services. Contact your Common Interface service provider to get more information about the modules and subscription. Please noted that CA modules and smart cards are neither supplied nor optional accessories from us. Auto Tuning DTV Manual Tuning ATV Manual Tuning Programme Edit Signal Information <
Summary of the content on the page No. 13
03 Remote control 1:POWER:To set the TV to standby or power on. POWER MUTE 2:NUMERIC KEY:For direct access to channels. 13 1 3:TV MENU:To display TV menu. AUDIO 4:CURSOR:To move within the menu. 14 1 2 3 5:CH.LIST:To display the channels list. 2 RECALL 6:VOL+/- :To adjust sound level. 4 5 6 15 7:PIC:To switch picture mode. 7 8 9 0 8:SLEEP:Set timer to turn off the TV. TV MENU SOURCE 9:FREEZE : To freeze the picture. 16 3 10:EPG:To display information about the program being viewed and w
Summary of the content on the page No. 14
REMOTE CONTROL TELETEXT Teletext is an information system broadcast by certain channels which can be consulted like a newspaper. It also offers access to subtitles for viewers with hearing problems or who are not familiar with the transmission language(cable networks, satellite channels, etc.) Press: You will obtain : This is used to call or exit teletext modes. The summary appears with a list of items that can be accessed. Each item has a corresponding 3 digit page number. If the chan
Summary of the content on the page No. 15
04 OPERATION Installation Guide Tune Type DTV+ATV Please select an OSD Language Germany Italy Norway Luxembourg Cesky English Magyar Polski Greece Poland Fran ais ~ Hungary Netherlands Portugal Espanol Dansk Hrvatski Nederlands Portugues MENU Deutsch E ka Italiano Norsk Pycck OK Pls press to select country at first , then press OK button to start auto tuning . Mode Select Channel Tun
Summary of the content on the page No. 16
Once your favorite group is created, you can ATV Manual Tuning press the FAV key to quickly access your favorite _ channel. Storage To 1 + 5). CI information: (optional) System BG This menu can display the CI card' s information. Current CH 1 2. PICTURE MENU The second item of the MENU is PICTURE MENU. Search You can adjust picture effect here, such as Fine-Tune contrast, brightness, etc. Press OK to move, press OK to adjust. Frequency 255.25 MHz Save
Summary of the content on the page No. 17
NOTE: The default pass word is 0000, If you forget the Clock -- -- -- -- password, you can use the super password:9443. Off Time Block program: Press to choose the On Time program ,press teletext green button to block Sleep Timer < > TIME Auto Sleep the program. If you want unblock the program, Time Zone pls enter the main menu , input the password, then press green button again.Parental guidance: Press to choose rating.
Summary of the content on the page No. 18
8.PVR function 1.Prepare to record the program From OPTION MENU enter into PVR File Select Disk C: System in “OPTION MENU”, please Check PVR File System Start choose “check PVR File System”. Click USB Disk “OK”, until “checking”change into Format “Success”. Note: please check the term “speed”. If it Time Shift Size Speed is “HD support”, that means the speed of USB device is available for time shift and Free Record Limit 6 Hr. record
Summary of the content on the page No. 19
2.Record the program (Suggest to format the device by “High Speed Fs...”, which can speed up As playing the DTV source, choose the channel and click “record”, the record the record.) frame will pop up. Click “record” again, Format disk the record frame will disappear and the “REC” icon still on the left top. It will Format disk disappear until you click “stop”. Warning! All data will be lost. 3.Play the record Start Exit In “USB”, the record program will be
Summary of the content on the page No. 20
9.Timeshift function 1.Prepare to record the program 00:00:33/00:04:22 This TV allows you to pause and record the currently watched digital program to a USB Play FB FF Prev. Next Pause Stop storage device, and to resume to the point where it was paused. NOTE: NOTE: Formatting a USB 2.0 storage device will Please do not unplug the USB storage be needed. Save your original data device when the Time Shift function is before formatting. All the data stored in activated. the USB device will
