Summary of the content on the page No. 1
R
USER’S MANUAL
L42H761
Thank you very much for choosing the AOC Envision Series LCD TV.
We recommend that you take a few minutes to read carefully through this manual
before installing and using the TV. Please keep this manual in a safe place for
your future reference.
www.AOC.com
Summary of the content on the page No. 2
LCD TV USER’S MANUAL TABLE OF CONTENTS FOR YOUR SAFETY ------------------------------------------------------ 1 DECLARATION OF RoHs COMPLIANCE --------------------------- 3 PRECAUTIONS AND REMINDERS ----------------------------------- 4 IMPORTANT SAFETY INSTRUCTIONS ----------------------------- 6 MOUNTING THE TV BASE---------------------------------------------- 8 PREPARATION ------------------------------------------------------------- 9 TO USE THE REMOTE CONTROL ------------------------------
Summary of the content on the page No. 3
English FOR YOUR SAFETY Before operating the TV please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa- tion. This equip
Summary of the content on the page No. 4
SYMBOL SYMBOL DEFINITION DANGEROUS VOLTAGE: The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electrical shock to persons. SA 1965 INSTRUCTIONS: The exclamation point within on equilateral triangle to alert the User to the presence of important operating and maintenance (servicing) instruction In
Summary of the content on the page No. 5
English DECLARATION OF RoHs COMPLIANCE This product has been designed and manufactured in compliance with Directive 2002/95/ EC of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below: Substance Proposed Maximum Actual Concentration Concentration Lead (Pb) 0.
Summary of the content on the page No. 6
PRECAUTIONS AND REMINDERS Place unit on even surfaces. Don’t place the TV in confined spaces or in a box when using it. Unplug immediately if is malfunction like Unplug immediately if other foreign no picture, no video/audio,smoke and bad materials are put inside TV box or if the odor from TV. TV fell down. Don’t throw any object inside the TV box Prohibit/Avoid opening TV cabinet like metals or other flammable materials. 4 English
Summary of the content on the page No. 7
English Remember to unplug the AC cord from Avoid direct sunlight, dusty, high humidity the AC outlet before cleaning. Do not use and smoky areas. liquid cleaners or aerosol cleaners to clean the display. Make sure to unplug the unit when not in Call service personnel to clean the use for a long period of time (days). internal part of the TV once a year. Do not cover or block any vents and Do not place the display near water, openings. Inadequate ventilation may such as bathtub, washbasin, k
Summary of the content on the page No. 8
IMPORTANT SAFETY INSTRUCTIONS Read before operating equipment 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do
Summary of the content on the page No. 9
English 18. Tilt/Stability – All televisions must comply with recommended international global safety standards for tilt and stability properties of its cabinets design. - Do not compromise these design standards by applying excessive pull force to the front, or top, of the cabinet, which could ultimately overturn the product. - Also, do not endanger yourself, or children, by placing electronic equipment/toys on the top of the cabinet. Such items could unsuspectingly fall from the top of the
Summary of the content on the page No. 10
MOUNTING THE TV BASE The TV base will be separated with the TV unit. You should Install the base before you use the TV unit. 1. Place the TV on its face on a soft blanket. 2. Install the base stand with three screws. 3. Place the TV on the table. WALL MOUNT Use of Wall Mount Bracket: 1. Remove the hinger cover. 2. Remove the 6 units M4.0 screws. 3. Remove the base ass’y. 4. Fasten four units M6.0 X 10mm screws to secure the wall mount bracket. 8 English
Summary of the content on the page No. 11
English PREPARATION Please, make sure to connect the power plug to the wall outlet socket after connecting the TV to the power cord! Min 1m 1. Install the base stand; place the TV on a solid surface. Ensure that the TV is placed in a position to allow free flow of air. Do not cover the ventilation openings on the back cover. To prevent any unsafe situations, no naked flame sources, such as lighted candles, should be placed on or in the vicinity. Avoid heat, direct sunlight and exposure to rai
Summary of the content on the page No. 12
3. Remote control: Remove the cover of the battery compartment. Insert the 2 batteries supplied (Type AA 1.5V). 4. Power: Insert the power cord in the wall socket having an AC power supply. You can see LED states at the front panel. If the LED color is Green, means the TV set is power on. If the LED color is Orange, which means this TV set is in standby state. 5. Turn the TV on: Push the POWER key on the Remote control or the Front panel control knobs. Wait a minute, the TV will power on an
Summary of the content on the page No. 13
English TO USE THE REMOTE CONTROL MUTE Press to set TVsound mute ON/ POWER OFF Press to power ON/OFF (standby) TV.(Note:1.TV is never completely PREV CH power off. Press to display the previous TV . unless physically unplugged. MTS/SAP 2.Press to turn on TV after the Press to activate the NTSC TV power sounds, such as: Stereo, SAP or on status LED had changed to the Mono tone. amber color and stopped flashing. ) WIDE VIDEO Press to choose the display aspect Press repeatedly to choose S-V
Summary of the content on the page No. 14
WIDE Press this button to display a list of available display for- mats. Available display formats are determined by the type of signal you are receiving. To choose the display format you prefer, press the WIDE button repeatedly: Automatic, Super Zoom, 4:3, Movie expand 14:9, Movie expand 16:9, 16:9 subtitle and widescreen. Automatic Super zoom 4:3 Movie expand 14:9 Movie expand 16:9 16:9 subtitle Widescreen Super Zoom, Movie expand 14:9, Movie expand 16:9 and 16:9 subtitle makes the pictu
Summary of the content on the page No. 15
English PERIPHERAL CONNECTION GUIDE AC POWER Head Phone R L Video S-Video POWER HDMI 2 HDMI 1 Audio In AV 1 Component 1 TV Cable RS-232 D-SUB SPDIF S-VIDEO Component 2 Component Line In VGA Headphone HDMI S-Video Pr Pb Y L R PC L/R 15-pin D-Sub Once your equipment is connected, use the following procedure to view the input signal: Press the source button on the remote controller to select the relevant source to view. (ex: Press VIDEO button to select “Composite Rear” if you have connected a v
Summary of the content on the page No. 16
CAMERA CAMCORDER VIDEO GAME How to connect 1. Connect the camera, camcorder and game set to the ports of the audio/video set. 2. The camcorder may get better picture by connecting a S-VHS cable between the S terminal and the Audio set. How to use it 1. Select the video AV or S terminal input. 2. Enable the exterior AV equipment. Warning: In case you notice scrolling images, wrong colors or no color, no picture or even combinations of these, on your screen, check if the connections are done
Summary of the content on the page No. 17
English To use the menus Introduction When you use a menu or take an action, convenient instructions, help texts and messages will be displayed on your TV. Please, follow the displayed instructions and read the help text on the specific item high- lighted. The buttons perform different actions, when using on screen menu. By pressing the corresponding button on the remote control to perform the required action when using these menus. How to navigate through the Settings menus The Settings m
Summary of the content on the page No. 18
1 1 TV menu-Installation Select the menu language Press the MENU button on the remote control. Settings Installation Language 2 6 3 Use the cursor down to select Installation in Language English the Settings menu. Autoprogram Français 3 Use the cursor right to enter the Installation Source Español Clock menu. Current software info 4 Select Language and enter the list of available Reset AV settings languages with the cursor right. 5 Select your preferred language with the cursor up/down
Summary of the content on the page No. 19
English 1 Channel tuning Available channels: - Cable (analog NTSC or digital QAM) - Terrestrial (analog NTSC or digital ATSC) If a tuned channel is not yet in the master channel map, the TV will attempt to tune to the channel and it will be added to the map. If the channel is not acquired, a message will ap- pear reporting that the channel is not available. When you tune an audio-only digital subchannel, a display appears with the message Audio only. Note: Digital Channel selection N
Summary of the content on the page No. 20
1 1 1 Source This menu allows you to identify the accessory Settings devices you have Installation 7 Source 8 connected to the external inputs/outputs. Language TV Autoprogram Component1 Press the MENU button on the remote control. Source Component2 2 Use the cursor down to select Installation in the Clock AV1 Weak channel installation HDMI1 Settings menu. Current software info HDMI2 3 Using the cursor up/down to choose Current Reset AV settings AV2 software info the TV software informatio
