Summary of the content on the page No. 1
Summary of the content on the page No. 2
Contents Introduction Warning Caution Main Unit Description Remote Control OSD basic adjustment Specification Trouble Shooting 1
Summary of the content on the page No. 3
Introduction Thank you very much for your purchase of our product of PDP TV. It serves as a normal color TV and PC monitor. To enjoy your TV to the full from the very beginning, read this manual carefully and keep it handy for ready reference. INSTALLATION Locate the TV in a room where direct light does not strike the screen. Total darkness or a reflection on the picture screen can cause eyestrain. Soft and indirect lighting is recommended for comfortable viewing. Allow enough
Summary of the content on the page No. 4
Warning CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO AVOID THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. o alert the user to avoid the risk This symbol is intended t of electric shock, do not disassemble this equipment by anyone except a qualified service personnel. This symbol is intended to alert
Summary of the content on the page No. 5
Caution Caution High voltages are used in the operation of this product. - Do not open the product's casing. Refer servicing to qualified service personnel . Caution To prevent fire or electrical shock hazard, Do not expose the main unit to moisture. Caution Do not drop or push objects into the television cabinet slots or openings. Never spill any kind of liquid on the television receiver. Caution
Summary of the content on the page No. 6
Caution Caution Never stand on, lean on, push suddenly the product or its stand. You should Pay special attention to children. Caution Do not place the main unit on an unstable cart stand, shelf or table. Serious injury to an individual, and damage to the television, may result if it should fall. Caution When the product is not used for an extended period of time, it is advisable t
Summary of the content on the page No. 7
Main unit description Control Panel Button Function VOL+ : Volume up. VOL- : Volume down. CH+: TV channel up. CH- : TV channel down. MENU : Press to select the main menu. TV/AV : Select the input signal. POWER : Switch on when in standby mode or enter the standby mode. TV Terminal Connections 1. HDMI1 input terminal. 2. HDMI2 input terminal. 3. HDMI3 input terminal. 4. VGA input terminal. 5. PC audio input terminal. 6. VIDEO2 input terminal. 7. AUDIO2 input terminal.
Summary of the content on the page No. 8
Locations of wall mout, power and terminals NOTE ●The TV dose not support wake sleep ● It supports must more than 2 GB It supports FAT/FAT32 document. The max FAT document is 4GB and the max FAT32 document is 2TB. 7
Summary of the content on the page No. 9
Remote control POWER: Power on/off button, press once to turn the TV on and press again to turn the TV off. MUTE: Press this button to mute or restore sound. FREEZE Press this key to hold the picture SLEEP: Set the sleep timer. ASPECT: Press to adjust picture ratio. EPG Enter electronic program guide CC: Press this key to select the CC Mode. Three CC Mode are available including On, CC on mute and off AUTO: Adjust the picture automatically in pc mode. PMODE: Select picture mod
Summary of the content on the page No. 10
OSD basic adjustment Installation Guide . Press MENU button to display the MAIN OSD MENU; . Press ◄ / ►button to select the MENU you want;Press ENTER button to enter the sub menu; . Press ▼ / ▲ button to select the option and then press ◄ / ► to adjust the value in the sub menu; . You can press MENU button to go back to the upper menu or EXIT button to close the OSD. PICTURE Press ENTER when the Picture Settings item is highlighted. Then you will go to the sub-menu as following.
Summary of the content on the page No. 11
Picture Settings Press ▼ / ▲ button to select Picture Settings, then press ◄ / ► button to adjust. Only in the User mode, the detail options as following can be adjusted. . Press ▼ / ▲ button to select Brightness,then press ◄ / ► button to adjust. . Press ▼ / ▲ button to select Contrast,then press ◄ / ► button to adjust. . Press ▼ / ▲ button to select Colort,then press ◄ / ► button to adjust. . Press ▼ / ▲ button to select Sharpness,then press ◄ / ► button to adjust. . Press ▼ / ▲ bu
Summary of the content on the page No. 12
Screen Size Press ▼ / ▲ button to select Screen Size, then press ◄ / ► button to adjust. Auto Wide Press ▼ / ▲ button to select the item Auto Wide, then press ENTER button to adjust. It can set the picture to fit the screen automatically. When the Auto Wide is selected, the symbol will show as following: PC Settings Note : The pc settings only in pc mode .Press ENTER when the PC Settings item is highlighted. Then you will go the sub-menu as following. .Press to select
Summary of the content on the page No. 13
Press ▼ / ▲ button to select Auto Adjust, then press ENTER button to start auto adjusting. Press ▼ / ▲ button to select Horizontal Position,then press ◄ / ► button to adjust. Press ▼ / ▲ button to select Vertical Position, then press ◄ / ► button to adjust. Press ▼ / ▲ button to select Clock, then press ◄ / ► button to adjust. Press ▼ / ▲ button to select Phase, then press ◄ / ► button to adjust. Press ▼ / ▲ button to select Reset, then press ENTER button to reset the options above.
Summary of the content on the page No. 14
Dynamic Contrast Press ▼ / ▲ button to select the item Dynamic Contrast, then press ◄ / ► button to adjust. it can adjust the contrast Film Mode Press ▼ / ▲ button to select the item Film Mode, then press ◄ / ► button to adjust. Noise Reduction Press ▼ / ▲ button to select the item Noise Reduction, then press ◄ / ► button to adjust. MPEG Noise Reduction Press ▼ / ▲ button to select the item MPEG Noise Reduction, then press ◄ / ► button to adjust. It can improve the quality of the pic
Summary of the content on the page No. 15
Bass Press ▼ / ▲ button to select the item Bass,then press ◄ / ► button to adjust. Treble Press ▼ / ▲ button to select the item Treble,then press ◄ / ► button to adjust. Balance Press ▼ / ▲ button to select the item Balance,then press ◄ / ► button to adjust. Surround Mode Press ▼ / ▲ button to select the item Surround Mode, then press ENTER button to adjust. Analog Sound Press ▼ / ▲ button to select the item Preferred Analog Sound, then press ◄ / ► button to select the prefer audio
Summary of the content on the page No. 16
Other Settings AVL Press ▼ / ▲ button to select the item AVL, then press ◄ / ► button to select ON or OFF. Auto Volume Level Speaker Press ▼ / ▲ button to select the item Speaker, then press ◄ / ► button to select ON or OFF. If set it Off, the speaker will be mute. Equalizer Mode Press ▼ / ▲ button to select the item Equalizer Mode, then press ◄ / ► button desired mode. 15
Summary of the content on the page No. 17
CHANNEL MENU Note: This menu is only shown when the input source is TV . Channel List Press ▼ / ▲ button to select Channel List , then press enter scan the Channel List. If you select the press enter button to option “In Channel List” On, the channel label will display in the list Favorite List Press ▼ / ▲ button to select Favorite List , then press ENTER button to scan the Favorite Channel List. 16
Summary of the content on the page No. 18
Channel Setting Press ▼ / ▲ button to select Manual Channel Setting , then press ENTER button to set the value in the sub menu. Channel Number Press ▼ / ▲ button to select Channel Number , then press ◄ / ► button to select the Channel Number. In Channel List Press ▼ / ▲ button to select In Channel List, then press ENTER button to Add or Delete the current channel in the channel list. 17
Summary of the content on the page No. 19
Press ▼ / ▲ button to select Channel Label, then press◄ / ► button to set the channel lable., and press ENTER button to edit next lable. Favorite Channel Press ▼ / ▲ button to select Favorite Channel, then press ENTER button to Add or Delete the current channel in Favorite Channel list. Signal Type Press ▼ / ▲ button to select Signal Type, then press button /” to select the type you want to set.There are two selections: Air and Cable. Auto Channel Search
Summary of the content on the page No. 20
PARENTAL CONTROL Input password to enter, default password is “0000”. V-CHIP Press ▼ / ▲ button to select V-CHIP, then press ENTER button to adjust. A Sub Menu Will appear as below. 19
