Summary of the content on the page No. 1
A17UX231
User's Manual
LCD TV
41T17TV673 5A6275
Summary of the content on the page No. 2
USER’S MANUAL TABLE OF CONTENTS INSTALLATION -------------------------------------------------------------------- 1 For Your Safety ---------------------------------------------------------------1 IMPORTANT SAFETY INSTRUCTIONS ------------------------------------- 3 PREPARATION -------------------------------------------------------------------- 4 OPERATING INSTRUCTIONS ------------------------------------------------ 6 Use of the remote control --------------------------------------------------
Summary of the content on the page No. 3
FOR YOUR SAFETY Before operating the TV please read this manual thoroughly. This manual should be retained for future reference. IMPORTANT SAFETY INSTRUCTIONS Read before operating equipment 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions. 8. Do not install ne
Summary of the content on the page No. 4
16. This product may contain lead or mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org 17. Damage Requiring Service – The appliance should be serviced by qualified service personnel when: A. The power supply cord or the plug has been damaged; or B. Objects have fallen, or liquid has been spilled into the appliance; or C. Th
Summary of the content on the page No. 5
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE Note to the CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. 22. Objects and Liquid Entry – Care should be taken so that objects do not fall and liq
Summary of the content on the page No. 6
2. Insert the aerial plug firmly into the aerial socket at the back of the TV. 3. Remote control: Remove the cover of the battery compartment. Insert the 2 batteries supplied (Type AAA 1.5V). 4. Power: Insert the power cord in the wall socket having an AC power supply. 5. Turn the TV on: Press the power button at the topside of the TV to turn it on. If the TV is turned off, the front light will also turn off. 6
Summary of the content on the page No. 7
OPERATING INSTRUCTIONS USE OF THE REMOTE CONTROL MUTE POWER Temporarily interrupt the Press to turn on/off the sound or restore it. TV. The TV is never completely powered off unless it is physically unplugged. DISPLAY Press this button to 0~9/100 Digit buttons Display Channel number To select a TV channel. on the right-top corner. CH Press or ( or ) to brows through the TV MTS /SAP channels,which are not Press this key to activate erased. To view a blocked Multichannel Television channel,
Summary of the content on the page No. 8
TO USE THE MENUS 1. Press the MENU button to display each menu 2. Use the cursor up/down to select a menu item. 3. Use the cursor left/right to enter a submenu or enable/disable the function. 4. Press the MENU button to exit the menu. MAIN MENU Press the MENU button into the main OSD (On Screen Display). Adjust item include PC SETUP 、SOUND SETUP 、OSD SETUP 、TV SETUP and PICTURE SETUP. PC Setup 1. Contrast, Brightness, Phase, Clock, H-Position, V-Position and Color are the functions for.
Summary of the content on the page No. 9
The “Reset To Default” is user-defined and is only used to reset the red, green, blue back to the default value. 4. Reset To Default is used to reset all settings to default value. Note: All the “Reset To Default” functions are the same except those in menus set by the user, which can reset all settings to default value in all menus. SOUND Setup 1. Volume is adjusted from 0 to 100. 2. Bass and Treble are adjusted from 0 to 100. You can adjust picture Volume, Bass and Treble to the levels you
Summary of the content on the page No. 10
OSD Setup 1. Set OSD language 2. Adjust the horizontal position of the OSD. 3. Adjust the vertical position of the OSD. 4. Adjust the OSD time-out. 5. OSD Background Adjustment 6. Show the resolution, H/V frequency and input port of current input timing. Do not execute reset, return to main menu. (Note: This item is available only in PC mode) 10
Summary of the content on the page No. 11
TV Setup 1. AIR/CATV for different TV input solution, RF and cable. 2. Auto searching is used for searching all TV program channels. After finishing search and exiting, the machine will save the program automatically, you can also press “menu” to break the searching, but only the searched programs are saved when the machine exits searching. 3. Add/Erase is for add or delete the current channel for memorizes. 4. Current Program is display the current channel number 。 5. Sleep Timer It is
Summary of the content on the page No. 12
Text Mode:TT1~TT4 Often used for channel guide, schedules, bulletin board information for Closed Caption programs, news, weather information or stock marker reports. Not all Closed Caption modes are necessarily being use by a TV channel during the transmission of a Closed Caption program. V-CHIP Setup Select V-Chip on OSD then enter 4 digits of pin number. Initial pin number is “0000”. If you enter an incorrect pin number “Error” message will be displayed. It is the parental control function
Summary of the content on the page No. 13
C. Setting up Movie Guidelines Use Up/Down arrow buttons to move around the matrix and press Right arrow button to change the value from “U” to ‘B” or “B” to “U” 13
Summary of the content on the page No. 14
D. CHANGE PIN Personal Identification Number is for change password to control the Vchip setup; it’s included three steps. ENTER PIN to enable this function, then ENTER NEW PIN to change a new one. After that COMFIRM NEW PIN. Picture Setup 1 、 Contrast,Brightness and Saturation are adjusted from 0 to 100. 2 、 Hue is adjusted from 0 to 100. 3 、 Sharpness is adjusted from 0 to100. Hue is only adjusted in NTSC telecast system. You can adjust contrast,brightness,saturation,hue,blacklevel and
Summary of the content on the page No. 15
CONNECT PERIPHERAL EQUIPMENT FRONT PANEL CONTROL KNOBS Power Key : Press to turn on or off the TV. MENU Key : Press to show the OSD menu and exit OSD menu at the TV. Down / Up Key : Press to perform select function and channel. - / + Key :Press to confirm your function selection and adjustment. Source Key : Press to select your input source. There is a wide range of video and audio equipment that can be connected to your TV. The following connection diagrams show you how to connect them. 15
Summary of the content on the page No. 16
PREPARATION Remove the back plate at the back of the TV as shown on the illustration opposite. Lay the LCD TV with the screen down on a table, as it will be easier to connect your peripheral equipment. Please take precaution not to damage the screen. ? 1: RF TV port ? 2: Earphone output port ? 3: Right channel input port ? 4: Left channel input port ? 5: AV video port ? 6: PC signal port ? 7: 12V power input port ? 8: S-VIDEO video port 16
Summary of the content on the page No. 17
VIDEO RECORDER How to connect 1. Connect the supplied antenna cable to the RF IN port of your VCR. 2. Connect another RF cable ① from the output RF of your VCR to the input of your TV. Better quality when playing from your VCR can be obtained if you also connect the Video, Audio LEFT AND right (only for stereo equipment) cables ⑤ to the VIDEO, AUDIO L and R inputs AV. If your VCR has an S-VHS video jack: For improved picture quality, connect a S-Video cable with the S-VIDEO input on the TV
Summary of the content on the page No. 18
DVD PLAYER Connect the video output port of DVD player to the video input port of TV. Connect the left and right channels of DVD to the left and right channels of audio input of TV. If your DVD player is equipped with S-VHS video port: For better quality picture, please connect the S port to the S input port ? of TV. Connecting the audio output ports ? ? through audio cable is a must since S port is not attached with audio How to play If you use connection ? , please select video AV input;
Summary of the content on the page No. 19
TIPS Care of the screen Do not rub or strike the screen with anything hard as this may scratch, mar, or damage the screen permanently. Unplug the screen before cleaning the screen. Dust the TV by wiping the screen and the cabinet with a soft, clean cloth. If the screen requires additional cleaning, use a clean, damp cloth. Do not use liquid cleaners or aerosol cleaners. Mobile telephone warning To avoid disturbances in picture and sound, malfunctioning of your TV or even damage to the TV, k
Summary of the content on the page No. 20
Product Specification 17” screen Feature XGA ( 1280 x 1024 ) Resolution Items Specification Screen Size 17” screen Aspect Ratio 4 : 3 Resolution 1280 x1024(XGA) Display Area (opening) 337.92 mmx270.336mm H x V LCD Panel Pixel Pitch 0.264mm x 0.264mm Display colors 16.2 million Lamp Type/Life 50000 hr Color Temperature Cool / Warm TV Standard NTSC M TV Function Sound systems MTS 、SAP Colour systems NTSC DPF function Supported by memory Not supported (Optional) card Wireless FM transmission
