Summary of the content on the page No. 1
Color GPS Chart Plotters/Fish Finder
CPF180i
CPF300i
Owner's Manual
CPF180i
CPF300i
Summary of the content on the page No. 2
WARNING!!! Electronic charts displayed by the GPS Chart Plotter are believed to be accurate and reliable, but are not intended to be a substitute for the official charts, which should remain your main reference for all matters related to the execution of safe navigation. For this reason we would like to remind you that you should carry on board and use the official published and approved nautical charts. FCC Compliance Statement This device complies with Part 15 of the FCC limits for Class
Summary of the content on the page No. 3
CAUTION - The GPS Chart Plotter is designed for maritime use. To avoid water intrusion ensure the C-MAP BY JEPPESEN C-CARD door is completely closed. - Extensive exposure to heat may result in damage to the GPS Chart Plotter. - The GPS Chart Plotter contains dangerous high voltage circuits which only experienced technicians can handle. - STANDARD HORIZON will not be liable for errors contained herein, or for incidental or consequential damages in connection with the performance or use of this ma
Summary of the content on the page No. 4
Page 6 CPF180i and CPF300i
Summary of the content on the page No. 5
TABLE OF CONTENTS 1. INTRODUCTION ...................................................................................................... 13 1.0 GENERAL INFORMATION .................................................................................... 13 1.1 PACKING LIST ...................................................................................................... 13 1.1.0 CPF180i Packing List ................................................................................ 14 1.1.1 CPF300i
Summary of the content on the page No. 6
4. FIND SERVICES ...................................................................................................... 41 4.0 USING FIND SERVICES & MORE FUNCTIONS .................................................. 41 4.0.0 Port Services .............................................................................................. 41 4.0.1 Port ...................................................................................................... 41 4.0.2 Tide Stations ...........................
Summary of the content on the page No. 7
9.6 OTHER SETTINGS IN ROUTE MENU .................................................................. 70 9.6.0 Route Checking ......................................................................................... 70 10. TRACKS ...................................................................................................... 71 10.0 TRACKING ...................................................................................................... 71 10.0.0 Saving and starting a new Track .......
Summary of the content on the page No. 8
13.4.0 Navigating a Route in Simulation mode .................................................... 94 13.5 DSC POLLING ...................................................................................................... 94 14. AIS ...................................................................................................... 95 14.0 AIS SYSTEM DEFINITIONS .................................................................................. 95 14.1 AIS MENU ..................................
Summary of the content on the page No. 9
17.8.0.1Auto Range ................................................................................. 119 17.8.0.2Bottom Lock ............................................................................... 119 17.8.1 Depth .................................................................................................... 119 17.8.2 Shift .................................................................................................... 119 17.9 INTERFERENCE REJECTION ...........................
Summary of the content on the page No. 10
Page 12 CPF180i and CPF300i
Summary of the content on the page No. 11
1. INTRODUCTION Congratulations on your purchase of the Standard Horizon GPS Chart Plotter. Whether this is your first GPS Chart Plotter/Fish Finder, or if you have other STANDARD HORIZON equipment, the STANDARD HORIZON organization is committed to ensuring your enjoy- ment of this GPS Chart Plotter/Fish Finder. STANDARD HORIZON technical support personnel stand behind every product we sell, and our Product Support team invites you to contact us should you require technical advice or assistance,
Summary of the content on the page No. 12
following contents. If any parts are missing contact the dealer this GPS Chart Plotter was purchased from. Accessories and replacement parts may be ordered from STANDARD HORIZON’s Parts Department at 767/827-7600 ext 6800 or e-mail at yaesuparts@vxstdusa.com. 1.1.0 CPF180i Packing List PART CODE ITEM S8002224A External bracket S8002225 Mounting knob with two washers S8002222 Dust cover T9101553 Power data cable EM022U104 Owner’s Manual EM023U510 Quick Reference Guide 1.1.1 CPF300i Packing List P
Summary of the content on the page No. 13
MDS-10-4 4kW 48 Mile 4Ft Open Array MDS-10-5 4kW 48 Mile 5Ft Open Array NOTE For additional information, refer to the Radar Installation and Radar Operation Manuals located at www.standardhorizon.com. CPF180i and CPF300i Page 15
Summary of the content on the page No. 14
Page 16 CPF180i and CPF300i
Summary of the content on the page No. 15
2. INSTALLATION NOTE Throughout this Owner’s Manual same conventions are used. See the legend below: [MENU]If you see brackets around a bold and capital letter word this refers to a key press. [CHART] If you see brackets around a bold and small capital letter word this refers to a Soft Key press. GENERAL SETUP When a word(s) is bold capital letters and underlined, this refers to a menu selection item. A GPS receiver and antenna are located inside the CPF180i and CPF300i and are designed to be br
Summary of the content on the page No. 16
Figure 2.1 - Example of Bracket installation (CPF180i on the left side and CPF300i on the right side) 2.2 FLUSH MOUNTING The CPF180i and CPF300i are supplied with a flush mount template for the cutout hole and screw holes required to install the GPS Chart Plotter. NOTE Before drilling holes make sure there is enough room to mount the GPS Chart Plotter and there are no obstructions. 1. After a location is found, peel the template label from the backing and apply the label t
Summary of the content on the page No. 17
Figure 2.2 - Example of Flush installation CPF180i Figure 2.2a - Example of Flush installation CPF300i 2.3 MOUNTING THE OPTIONAL EXTERNAL GPS ANTENNA An external WAAS GPS antenna is available when the CPF180i or CPF300i is flush mounted or mounted in an area where satellite reception is not possible with the internal antenna.This antenna is designed to be mounted on a base, installed on an extension or flush mounted. Choose a location for the antenna that has a clear view of the sky and is no
Summary of the content on the page No. 18
The thread used on the antenna is an industry standard (1inch 14TPI) used on a wide range of mounting brackets. Due to the manufacturing process of these mounting brackets, the antenna may not tighten all the way down onto all the threads. This is no concern however as the antenna must be tightened until the antenna stops rotating. NOTE The antenna cable can be cut and spliced to ease installation. Care must be taken when reconnecting the antenna cable to protect from water and corrosion. 2.3.0
Summary of the content on the page No. 19
GPS OVERALL SHAPE Figure 2.3.0a - Installing the External GPS Antenna (II) Smart GPS Cable Pin Wire Color Description 1 Red Battery Positive 2 Green Smart GPS NMEA Output 3 Brown Smart GPS NMEA Input 4NC 5NC 6 Black/Yellow Battery Ground 2.4 CONNECTIONS The CPF180i and CPF300i have connector that allow them to be connected to a power supply, option WAAS GPS antenna, NMEA Devices such as Optional Video Camera (CPF300i only) VHF’s, AIS Receiver, Digital Instruments, Autopilots. NOTE The GPS Char
Summary of the content on the page No. 20
Instrument). If the autopilot connections are made to Port 3 (Yellow wire) and the autopilot is not reading the sentences, change the connections to Port 1 (Brown) and change the sentences to APA, APB, BOD, GGA, GLL, RMC and XTE. 2.4.1 Connection For CPF180i 2.4.1.1 DC Power Connection Optional WAAS GPS antenna CPF180i Red Switch Black - + 2A Battery Fuse PWR & ACC 1 Cable 10-35Vdc Transducer 2.4.1.2 Connection of the AIS receiver, VHF and Autopilot Optional WAAS GPS Red antenna Switch Black -
