Summary of the content on the page No. 1
1600
Model: 201042
LIT. #: 98-1513/11-09
ENGLISH
1
Fusion_1600_ARC_Translated.indd 1 12/21/09 9:56 AM
Summary of the content on the page No. 2
2 Fusion_1600_ARC_Translated.indd 2 12/21/09 9:56 AM
Summary of the content on the page No. 3
CONTENTS English 4 - 26 Français 27 - 52 Español 53 - 78 Deutsch 79 - 104 Italiano 105 - 130 Português 131 - 156 3 Fusion_1600_ARC_Translated.indd 3 12/21/09 9:56 AM
Summary of the content on the page No. 4
™ Fusion 1600 ARC™ - Laser Rangefinder Binocular 201042 An advanced Fusion of our finest technologies. The ultimate in efficiency, our new Fusion 1600 ARC melds the best of 10x42 Bushnell binoculars with world- leading laser rangefinding capabilities. Every detail is magnified with rich contrast and stunning clarity from edge to edge using premium fully multi-coated optics and BAK4 prisms. At the push of a button, it displays the exact distance to your target from 10 to 1,600 yards. With bui
Summary of the content on the page No. 5
HOW OUR DIGITAL TECHNOLOGY WORKS The Fusion™ 1600 ARC™ emits invisible, eye safe, infrared energy pulses. The Fusion 1600 ARC‘s Advanced Digital microprocessor and ASIC chip (Application-Specific Integrated Circuit) results in instantaneous and accurate readings every time. Sophisticated digital technology instantaneously calculates distances by measuring the time it takes for each pulse to travel from the rangefinder, to the target, and back. RANGING ACCURACY The ranging accuracy of the Fusi
Summary of the content on the page No. 6
GETTING STARTED INSERTING THE BATTERY The battery compartment is located between the objective barrels. Simply remove the battery cap by rotating it counter clockwise and insert a CR-123 3-volt lithium battery into the compartment negative end first, then replace the battery cap. NOTE: It is recommended that the battery be replaced at least once every 6 months. SETTING THE DISPLAY FOCUS AND DIOPTER ADJUSTMENT Before you begin using your laser rangefinder binoculars, a few simple, one-time a
Summary of the content on the page No. 7
5. Finally, view the same object through only the left side of the binocular, and rotate the diopter adjustment (left eyecup) until it appears sharp to your left eye (do not touch the center focus knob while doing this). This compensates for any vision differences between your left and right eyes. Once set, note the number on the left and right binocular tubes that the index mark on each eyecup is lined up with. With the display focus and diopter adjustment set to these position
Summary of the content on the page No. 8
Angle Range Compensation Modes Rifle Mode (1) 12 Bow Mode (2) 1 Battery Life Indicator (3) 4 2 Aiming Circle (4) Active Laser (5) 6 3 5 Targeting Modes SD BullsEye Mode (6) 7 8 Brush Mode (7) 10 9 11 13 Primary Numeric Display displays Line-of-sight Distance (8) Holdover / Bullet-drop measure for Rifle Mode MOA (9) CM (10) IN (11) SD = Variable Sight-In Distance (12) Secondary Numeric Display (13) (Toggles from Degree of Angle to Holdover / bullet drop for Rifle mode) (Toggles fro
Summary of the content on the page No. 9
ANGLE RANGE COMPENSATION The Fusion 1600 ARC is an advanced premium laser rangefinder binocular featuring a built-in accelerometer-based inclinometer that digitally displays the exact angle from -90 to +90 degrees of elevation and is +/- 1.0 degree accurate. The Bushnell® Fusion 1600 ARC™ solves a problem hunters have been faced with for years. The problem: Bow and rifle hunters have struggled with extreme uphill and downhill angles because of how these angles alter true horizontal distance
Summary of the content on the page No. 10
Battery Indicator: Full charge 2/3 battery life remaining 1/3 battery Life remaining Battery Indicator Blinks - Battery needs to be replaced and unit will not be operable. UNIT OF MEASURE OPTIONS The Fusion 1600 ARC can be used to measure distances in yards or meters. The unit of measure indicators are located in the lower right portion of the LCD. ACTIVE LASER Crosshairs surrounding the aiming circle indicate that the laser is being transmitted. Once a range has been acquired, you
Summary of the content on the page No. 11
approximately 3 seconds and move the rangefinder from object to object while leaving the POWER button depressed. Automatic SCAN will allow the range to be continuously updated as multiple objects are targeted. ™ BullsEye (LCD Indicator - ) This advanced mode allows easy acquisition of small targets and game without inadvertently getting distances to background targets that have stronger signal strength. When more than one object has been acquired, distance of the closer object will be display
Summary of the content on the page No. 12
force the laser to hit multiple objects to ensure that you are only displaying the closest of the objects recognized by the laser. ™ Brush (LCD Indicator - ) This advanced mode allows objects such as brush and tree branches to be ignored so that distance only to background objects are displayed. When more than one object has been acquired, distance of the further object will be displayed and a circle will surround the Brush™ indicator informing the user that distance of the farthest object i
Summary of the content on the page No. 13
force the laser to hit multiple objects to ensure that you are only displaying the furthest of the objects recognized by the laser. Once the device has shut off, the unit will always default back to the last targeting mode used. MENU SETUP – SELECTION OF BOW, RIFLE, REGULAR MODES, UNIT OF MEASURE, SIGHT-IN DISTANCE, BALLISTIC CORRECTION AND DISPLAY BRIGHTNESS There are two ARC (Angle Range Compensation) modes and one REGULAR mode. The two ARC modes are BOW mode and RIFLE mod
Summary of the content on the page No. 14
If the user chooses RIFLE mode, and after having determined unit of measure, the user has the following options: 1. Variable Sight-In (VSI™) - Allows the rifle hunter to choose from four sight-in distances (100, 150, 200, or 300 yards or meters) and provides holdover / bullet-drop data in inches, centimeters or MOA. The “SD” (Sight- In Distance) indicator will turn on and the current Sight-In Distance number will blink within the display (I.e. 100, 150, 200, or 300). The Sight-In Distance opti
Summary of the content on the page No. 15
MODE button will toggle between the four brightness settings. “ ” is the lowest intensity while “ ” Is the brightest. Simply press the MODE button until the desired brightness setting is displayed and select by pressing and releasing the POWER button. Upon returning to the normal operating menu, the current compensation mode and unit of measure will be identified in the display as indicated below. SETUP menu
Summary of the content on the page No. 16
When the unit automatically powers down, operation will always return to the normal operation (i.e. away from SETUP) with the last used ARC mode active (i.e. BOW, RIFLE, or REGULAR) along with the last used TARGETING modes active (Standard SCAN, BULLSEYE, or BRUSH). If the unit turns off while in the SETUP menu, the unit will always return to the last mode(s) still active. Once the range is displayed, continue to hold the POWER button down for approximately 2 seconds while holding the aiming
Summary of the content on the page No. 17
If in BOW mode, the line of sight distance will display in the primary numeric display and the inclination and horizontal distance will display in the secondary numeric displays. Bushnell determined through extensive testing and interviews with high-profile bow hunting experts that multiple bow ballistic groups were not necessary. Bow-hunters want to know true horizontal distance because that is how they practice shooting, and once they confidently know that, they can make any necessary adju
Summary of the content on the page No. 18
If in RIFLE mode, the ballistic group will be displayed in the bullet drop numeric field anytime that the primary numeric display is showing dashes (i.e. no target acquired). When a target is acquired in RIFLE mode, the line of sight distance will display in the secondary numeric displays. The “IN” icon (i.e. inches) will light next to the bullet drop numeric display, if the unit of measure is set to Yards (Y). If the unit of measure is set to Meters (M), the bullet drop will be calculated a
Summary of the content on the page No. 19
Winchester .224 dia. 22-250 Rem, 55 gr. Ballistic Silvertip at 3680 FPS H Winchester .224 dia. 22-250 Rem, 55 gr. PSP at 3680 FPS G Federal Cartridge .277 dia. 270 Win, 150 gr. Ballistic Tip at 3060 fps F Federal Cartridge .277 dia. 270 Win, 150 gr. Partition at 3000 fps F Remington Arms .277 dia. 270 Win, 140 gr. PSPCL Ultra at 2925 FPS E Remington Arms .277 dia. 270 Win, 150 gr. SPCL at 2850 FPS D Winchester .277 dia. 270 Win, 150 gr. Partition Gold at 2930 FPS E Winchest
Summary of the content on the page No. 20
After you have determined which ballistic group corresponds to your caliber and load, select this ballistic group (See MENU SETUP above). The internal formula will determine amount of bullet drop/holdover in inches or centimeters based upon distance, angle, and ballistics of your caliber and load. This state-of-the-art digital technology allows the hunter or shooter to know precisely where to hold for an effective shot. This information should be treated as a helpful guide or tool and in no
