Summary of the content on the page No. 1
SERVICE MANUAL
FACSIMILE
GD-1210/1250/1270/1160/1260
File No. SME060009D0
R060121A4400-TTEC
Ver04_2011-12
Summary of the content on the page No. 2
Trademarks • The official name of Windows XP is Microsoft Windows XP Operating System. • The official name of Windows 7 is Microsoft Windows 7 Operating System. • Microsoft, Windows, Windows NT, Windows Vista and the brand names and product names of other Microsoft products are trademarks or registered trademarks of Microsoft Corporation in the U.S. and/or other countries. • Apple, AppleTalk, Macintosh, and Mac are trademarks of Apple Computer, Inc. in the U.S. and other countries. • PostScri
Summary of the content on the page No. 3
GENERAL PRECAUTIONS REGARDING THE SERVICE FOR GD-1210/1250/1270/1160/1260 The installation and service shall be done by a qualified service technician. 1) Transportation/Installation - When transporting/installing the equipment, employ four persons and be sure to hold the posi- tions as shown in the figure. The equipment is quite heavy and weighs approximately 120 kg (264.55 lb.), therefore pay full attention when handling it. (e-STUDIO2500c/3500c/3510c, e-STUDIO2330C/2820C/2830C/ 3520C/353
Summary of the content on the page No. 4
- Select a suitable place for installation. Avoid excessive heat, high humidity, dust, vibration and direct sunlight. - Provide proper ventilation since the equipment emits a slight amount of ozone. - To insure adequate working space for the copying operation, keep a minimum clearance of 80 cm (32”) on the left, 80 cm (32”) on the right and 10 cm (4”) on the rear. - The equipment shall be installed near the socket outlet and shall be accessible. - Be sure to fix and plug in the power cable sec
Summary of the content on the page No. 5
- During servicing, be sure to check the rating plate and cautionary labels such as “Unplug the power cable during service”, “CAUTION. HOT”, “CAUTION. HIGH VOLTAGE”, “CAUTION. LASER BEAM”, etc. to see if there is any dirt on their surface and if they are properly stuck to the equipment. 5) Disposal of the Equipment, Supplies, Packing Materials, Used Batteries and IC-RAMs - Regarding the recovery and disposal of the equipment, supplies, packing materials, used batter- ies and IC-RAMs including
Summary of the content on the page No. 6
Summary of the content on the page No. 7
CONTENTS GD-1210/1250/1270/1160/1260 1. SPECIFICATIONS AND OUTLINE OF SYSTEM ......................................................... 1-1 1.1 FAX Options ........................................................................................................................ 1-1 1.2 Specifications....................................................................................................................... 1-2 1.3 Features .................................................................
Summary of the content on the page No. 8
4.2 Description of Circuits.......................................................................................................... 4-3 4.2.1 Configuration ............................................................................................................ 4-3 4.2.2 Line path switching control circuit............................................................................. 4-5 4.2.3 Dial pulse generation circuit ......................................................................
Summary of the content on the page No. 9
1. SPECIFICATIONS AND OUTLINE OF SYSTEM 1 1.1 FAX Options Equipments can be used as a FAX by installing the FAX unit. Some options can be added when the FAX unit is installed or to extend the FAX functions ( P. 1-8 "1.5 Options"). Be sure to use the FAX unit and the 2nd line for the FAX unit only in the following combinations. Models FAX unit 2nd line for FAX unit e-STUDIO2500c/3500c/3510c GD-1210 GD-1160 e-STUDIO2330C/2820C/2830C/3520C/3530C/4520C, GD-1250 GD-1260 e-STUDIO2040C/2540C/3040C/35
Summary of the content on the page No. 10
1.2 Specifications 1) Main system - Type Desktop type transceiver -Operation Transmission Manual/Automatic Reception Manual/Automatic 2) Scanner [ ]: at rotation transmission - Horizontal direction 16 lines/mm, 8 lines/mm [15.4 lines/mm, 7.7 lines/mm, 3.85 lines/mm] - Vertical direction 15.4 lines/mm, 7.7 lines/mm, 3.85 lines/mm [16 lines/mm, 8 lines/mm] - Combination U-Fine: 16 x 15.4 lines/mm [15.4 x 16 lines/mm] Semi-U-Fine:8 x 15.4 lines/mm [15.4 x 8 lines/mm] Note Note: :
Summary of the content on the page No. 11
Original size A B LG 355.6 350.1 1 LD 431.8 426.3 3) Transmission system Circuits to be used: Subscriber line/FAX communication network (G3) - Calling automatic transmission (including the sequential multi-address transmission) - Calling automatic reception (polling reception) - Called automatic transmission (polling transmission) - Called automatic reception - Calling manual transmission - Calling manual reception - Called manual transmission - Called manual reception Communication mode High-s
Summary of the content on the page No. 12
4) Recording paper - Recording method Electrophotographic recording method by LSU (Laser Scanning Unit) - Horizontal printing density 24 lines/mm (96 lines/mm with the smoothing processing) [23.1 lines/mm (92.4 lines/mm with the smoothing processing)] - Vertical printing density 23.1 lines/mm (24 lines/mm with the smoothing processing) - Recording paper size and the effective printing area Unit: mm (inch) Paper size Dimension (width x length) Printing area A5-R 148 x 210 143 x 204.5 B5-R 182 x 2
Summary of the content on the page No. 13
1.3 Features • A3/LD scanning 1 Scans data across A3/LD width and transmits in A3/LD actual size. • High-speed scanning Inputs an A4/LT-size transmitted document in about 0.7 seconds (A4/LT document transmitted widthwise). • High-speed transmission 33.6 Kbps high speed modem Toshiba original high-speed communication modes EX and HS JBIG encoding system • Dual Access - FAX transmission There are two types of FAX transmission: Page-by-page direct transmission and memory trans- mission that all pa
Summary of the content on the page No. 14
• Phone Book (3,000 addresses) Up to 3,000 addresses can be registered in the Phone Book using the large LCD control panel. • Multi-address transmission function Data are sent to multiple addresses (400 destinations) in sequence in a single operation. There are three ways to choose/enter the address - Choose from the Phone Book (up to 400 destinations) - Direct dialing (up to 400 destinations) - Mix operation (Phone Book, Direct dialing, Group destinations: up to 400 destinations) • Memory recep
Summary of the content on the page No. 15
1.4 Accessories and Parts The following accessories and parts come with the FAX unit: 1 Accessory GD-1210 GD-1250 GD-1270 Operator’s manual (for facsimile function) 1 pc. 1 pc. 1 pc. Modular cord (2 m) 1 pc. 1 pc. 1 pc. Unpacking instruction 1 set 1 set 1 set Parts GD-1210 GD-1250 GD-1270 Fax unit 1 pc. 1 pc. 1 pc. SG3 label 1 pc. 1 pc. 1 pc. FCC Part 68 label (U.S.A.) / IC label (Canada): NA only 1 pc. 1 pc. 1 pc. DTS label (EU): EU only 1 pc. 1 pc. 1 pc. Teleprompt label (New Zealand): AU only
Summary of the content on the page No. 16
1.5 Options Extends the FAX functions when the FAX unit is installed. e-STUDIO2330C/ e-STUDIO2500c/ 2820C/2830C/ e-STUDIO5520C/ Option Function 3500c/3510c 3520C/3530C/ 6520C/6530C 4520C Reversing Automatic Feeds originals MR-3018 MR-3018 - Document Feeder (RADF) Finisher Sorts out docu- MJ-1101 MJ-1101 MJ-1103 ments to be output MJ-1030 MJ-1030 MJ-1104 for the FAX/copy- MJ-1031 ing operation 2nd line for FAX unit Adds one extra GD-1160 GD-1260 GD-1260 communication line e-STUDIO205L/255/305/35
Summary of the content on the page No. 17
e-STUDIO206L/256/306/356/ Option Function 456 1 Reversing Automatic Feeds originals MR-3021/3022 Document Feeder (RADF) Finisher Sorts out docu- MJ-1101 ments to be output MJ-1106 for the FAX/copy- MJ-1032 ing operation MJ-1033 MJ-5004 MJ-5005 MJ-5006 2nd line for FAX unit Adds one extra GD-1260 communication line © 2006 - 2011 TOSHIBA TEC CORPORATION All rights reserved GD-1210/1250/1270/1160/1260 SPECIFICATIONS AND OUTLINE OF SYSTEM 1 - 9 11/12
Summary of the content on the page No. 18
1.6 System List 1.6.1 e-STUDIO2500c/3500c/3510c Reversing Automatic Document Feeder ( ) RADF MR-3018 Saddle stitch finisher MJ-1030 Bridge Kit KN-3500 Finisher MJ-1101 FAX unit GD-1210NA/AU/AS/ EU/C/TW/KR 2nd Line for FAX unit GD-1160 NA/EU-N/C/TW Drawer Module Paper Feed Large Capacity MY-1031/C ( ) ( ) Pedestal PFP Feeder LCF KD-1018/C KD-1019 A4/LT/C Fig. 1-2 GD-1210/1250/1270/1160/1260 © 2006 - 2011 TOSHIBA TEC CORPORATION All rights reserved SPECIFICATIONS AND OUTLINE OF SYSTEM 1 - 10 08/0
Summary of the content on the page No. 19
1.6.2 e-STUDIO2330C/2820C/2830C/3520C/3530C/4520C Reversing Automatic 1 Document Feeder ( ) RADF MR-3018 Saddle stitch finisher MJ-1030 Bridge Kit Finisher KN-4520 MJ-1101 FAX unit GD-1250NA/AU/AS/ Hanging EU/C/TW finisher MJ-1031 2nd Line for FAX unit GD-1260 NA/AU/EU/C/TW Drawer Module Paper Feed Large Capacity ( ) ( ) MY-1032/C Pedestal PFP Feeder LCF KD-1023/C KD-1024 A4/LT/C Fig. 1-3 © 2006 - 2011 TOSHIBA TEC CORPORATION All rights reserved GD-1210/1250/1270/1160/1260 SPECIFICATIONS AND OU
Summary of the content on the page No. 20
1.6.3 e-STUDIO5520C/6520C/6530C Saddle stitch finisher MJ-1104 FAX unit GD-1270NA/AU/AS/ EU/C/TW Finisher MJ-1103 2nd Line for FAX unit GD-1260 NA/AU/EU/C/TW Fig. 1-4 GD-1210/1250/1270/1160/1260 © 2006 - 2011 TOSHIBA TEC CORPORATION All rights reserved SPECIFICATIONS AND OUTLINE OF SYSTEM 1 - 12 09/05
