Q-Logic Car Security System APS-610 user manual

User manual for the device Q-Logic Car Security System APS-610

Device: Q-Logic Car Security System APS-610
Category: Automobile Accessories
Manufacturer: Q-Logic
Size: 0.32 MB
Added : 11/4/2013
Number of pages: 10
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Q-Logic Car Security System APS-610. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Q-Logic Car Security System APS-610.

For your convenience

If looking through the Q-Logic Car Security System APS-610 user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Q-Logic Car Security System APS-610 on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Q-Logic Car Security System APS-610 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Q-Logic Car Security System APS-610 User manual - Online PDF
Advertisement
« Page 1 of 10 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Q-Logic Car Security System APS-610 but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Q-Logic Car Security System APS-610. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

Model APS-610
Installation Manual
SELECTABLE FEATURES
Note: The method of manual override can either be selected to operate from the valet switch or operate as custom
code. Be certain to place a check mark indicating the method used in the box located on the last page of
the owner's manual.
Note: When both Passive Arming and Voltage Sensing are selected, you must hardwire the driver’s door pin
switch in order to begin the passive arming sequence.
RF Programmable Features :
Feature Selection 1 C

Summary of the content on the page No. 2

Fourth Press and release the valet switch 3 chirps = headlight output when arming and disarming Press transmitter Lock button to change 4 chirps = headlight output off Press transmitter Lock button to change 1 chirp = headlight output when arming Press transmitter Lock button to change 2 chirps = headlight output when disarming or Fifth Press and release the valet switch 2 chirps = active locks Press transmitter Lock button to change 1 chirp = passive locks or Sixth Press and release the valet s

Summary of the content on the page No. 3

If during the program sequence receiver channel 1 is programmed, and received channel 2 is skipped over, as indicated in the transmitted program guide, then the unit will operate as a single button lock/unlock unit from that transmitter. It is possible to have one transmitter programmed for single button lock/unlock, and one transmitter programmed for separate button lock/unlock if the customer so desires. If you inadvertently incorrectly program the transmitter, please read the information on r

Summary of the content on the page No. 4

Whichever mounting method is selected, make certain that the sensitivity adjustment is accessible for use later in the installation. WIRING THE SYSTEM Large 10 Pin Edge Connector: Red/White (5Amp) & Red (15Amp) Fused Wires: +12 VDC Constant Battery Source This wire controls the sensitivity of the voltage sensing circuit, which detects the turning on of an interior light when a door is opened. It will also detect the switching on of parking or headlamps, and in many cases will trigger the alarm w

Summary of the content on the page No. 5

Orange Wire: 300 mA Ground Output When Armed - N. C. Starter Disable This wire is provided to control the starter cut relay. Connect the orange wire to terminal 86 of the relay. Connect relay terminal 85 to an ignition wire in the vehicle that is live when the key is in the on and crank positions, and off when the key is in the off position. (This is where the yellow wire from the alarm should be connected). Cut the low current starter solenoid wire in the vehicle, and connect one side of the cu

Summary of the content on the page No. 6

Note: This is a normally opened starter cut arrangement, and when power is removed from the security system, the starter disable feature will remain operational, and the vehicle will not start. Audiovox does not recommend using the Orange w/ White trace wire to interrupt anything but the starting circuit of the vehicle. Dark Green Wire: ( - ) INSTANT TRIGGER ZONE This is an instant on ground trigger wire. It must be connected to the previously installed hood and trunk pin switches. Brown Wire: -

Summary of the content on the page No. 7

2 Pin White Connector: Dash Mounted L.E.D. Route the red and blue wires in the 2 pin white connector from the L.E.D. to the control module, and plug it into the mating white connector on the side of the module. 4 Pin White Connector: Shock Sensor Route the red, black, green and blue wires in the 4 pin white connector from the shock sensor to the control module, and plug one end into the shock sensor, and the other end into the mating white connector on the side of the module. Normal Door Lock Op

Summary of the content on the page No. 8

Next, locate the drivers door unlock motor wire and cut it at a convenient location to allow wiring of the White and Dark Blue wires. Dark Blue will connect to the vehicle side of the cut wire and White will connect to the "Unlock Drivers Door Motor" side of the cut wire. Most vehicles door lock/unlock motor legs rest at ground, and switch +12 volts to the door lock/unlock motor legs for operation. If this is the case in the vehicle you are working on, connect Orange to a +12 volt source. In

Summary of the content on the page No. 9

COMPLETING THE INSTALLATION Antenna Wire: Be sure to extend the thin black antenna wire to it’s full length, and cable tie into place where it cannot be damaged. Avoid wrapping this wire around major, high current wire looms. Adjusting the Shock Sensor: If used, the sensitivity of the pre-detect circuit is automatically set 30% less sensitive than the full trigger circuit. Using a small screwdriver, gently turn the adjustment screw fully counterclockwise. (DO NOT over turn this screw. Maximum ro

Summary of the content on the page No. 10

© 2000 Audiovox Corporation, 150 Marcus Blvd., Hauppauge, N.Y. 11788 128-5758A


Alternative user manuals
# User manual Category Download
1 Sony RM-X32 User manual Automobile Accessories 2
2 Sony MV-100CAR User manual Automobile Accessories 1
3 Sony DC-FX1 User manual Automobile Accessories 0
4 Sony RM-X33 User manual Automobile Accessories 13
5 Sony RM-X38 User manual Automobile Accessories 3
6 Sony DCC L50 User manual Automobile Accessories 1
7 Sony CDX-T69X User manual Automobile Accessories 4
8 Sony 9 User manual Automobile Accessories 1
9 Sony RM-X1S User manual Automobile Accessories 156
10 Sony PEGA-CC5 User manual Automobile Accessories 1
11 Philips CID3287 User manual Automobile Accessories 0
12 Philips EcoVision 12342ECO User manual Automobile Accessories 1
13 Philips DA VEJLEDNING 37PFL8404H User manual Automobile Accessories 0
14 Philips DA VEJLEDNING 42PFL8404H User manual Automobile Accessories 1
15 Philips DA VEJLEDNING 47PFL8404H User manual Automobile Accessories 0