Summary of the content on the page No. 1
Rear Observation System Package
Model RVMPKG1
Installation Manual
Features:
• Rearview Mirror with 4” LCD
• 2 Built in Speakers
• Rearview Camera Input
• Auxiliary Video Input
• Video System Auto Detection for PAL/NTSC
• Cellular Phone Hands Free Input
• Hands Free Microphone Built-In
NOTE: Hands free feature may not operate with all
cellular phones and/or an adapter may be required.
Rearview camera optional.
1
Summary of the content on the page No. 2
TABLE OF CONTENTS Cautions! 3 Preface 4 WARNING:................................................................................... 4 Backing up vehicle ........................................................................ 4 Packing list 4 1. Installation Instructions 5 2. Install the mobile phone hands free seat 6 3. Signal Inputs 7 SW1 and SW2: 8 Specifications 9 General 9 Maintenance 9 Troubleshooting 10 2
Summary of the content on the page No. 3
Cautions! The product is intended to assist in safe driving and to allow the driver to have a broader rearview while the vehicle is in reverse. You, as the driver, are solely responsible for the safe operation of your vehicle and the safety of your passengers according to the country and their local traffic regulations. Do not use any features of this system to the extent it distracts you from safe driving. Your first priority while driving should always be the safe operation of you
Summary of the content on the page No. 4
Preface There is a blind spot that exists at the back of a vehicle while the vehicle is in reverse. Equipped with a camera, this electronic rearview mirror ensures safety by providing the driver with a clear and wide image of the area behind the vehicle while it is in reverse. WARNING: Backing up vehicle Do not back up vehicle while watching the mirror/monitor screen. Always look in the direction of vehicle motion. Use the mirror/monitor as an aid in safety confirmation. The d
Summary of the content on the page No. 5
1. Installation Instructions (1) Mount the mirror/monitor onto the existing rearview mirror. a) Stick two adhesive foam backings on to the back of mirror in the two small rectangle indents. b) Take the two seven inch belts and slide them into the slots on the top rear of the mirror with grooved side of the belt facing down.. Figure 1 c) Take the buckles and slide them into the lower slots on the rear of the mirror with the buckle facing down toward the seven-inch strap. Figur
Summary of the content on the page No. 6
windshield then down the A pillar behind the plastic shroud to the under dash area. (3) Connect the 5 wires in the following manner. a) Red wire - 12 volt constant (positive) b) Black wire - Chassis ground (negative) c) Blue wire - 12-volt ignition (12 volt with ignition on) d) Green wire - Reverse light switch (12 volt when vehicle is in reverse) e) Yellow wire – Parking brake light switch (Negative when parking brake on) WARNING: Observe polarity when connecting the cables. T
Summary of the content on the page No. 7
3. Signal Inputs The signal input connections for the system include: (1) Rear Camera: By connecting rear camera with control box plug, users can see the rearview camera image when the car is in reverse. (2) Hands Free Jack: Put the hands free plug (3.5mm) into hands free jack and put the other side of plug into the headphone jack of the mobile phone. (If necessary, try a compatible adapter). (3) Video In, Video Out, Audio In, Audio Out, Audio/Video Input and Output Plugs (3.5
Summary of the content on the page No. 8
4. Controls and Indicators Figure 6 Figure 6 illustrates the controls and indicators of the RVMPKG1 rear view mirror: A: Rearview mirror B: 4” LCD panel C: Hands free Microphone D: Brightness Control E: Power indicator (Red when power is on) F: Volume Control Knob G: Switch 1 (see below) H: Switch 2 (see below) J: 2-position Switch for hands free microphone Sensitivity High/Low Select K: Speakers SW1 and SW2: 1. Reversing: SW1: No Function LCD automatically tu
Summary of the content on the page No. 9
3. Vehicle Parked: SW1: Used to turn the LCD on/off when using the DVD/VCR player, provided the parking brake is engaged. SW2: When pressed and held, the rear camera image appears on the mirror. When released the LCD will turn off. The mirror will return back to its normal appearance. Specifications General Power Supply 12VDC Power Consumption <12W Current Draw <500 mA Video Input 1Vp-p@ 75 Impedance Audio Input <=1V Audio Power Output 0.5W × 2 (16O) Operating Temperature Rang
Summary of the content on the page No. 10
Occasionally clean the surface of the mirror with a soft cloth moistened with water or window cleaner. Troubleshooting Table 1 Rearview Mirror Symptoms Solutions The ON/OFF signal light is not 1. Check the installation-wiring diagram. on after the car is started? 2. Ensure that the parallel red and black line from the control box is connected properly. 3. Check for 12 volts on the blue wire while Ign on. No video signal appears while 1. Check the LCD Contrast (Brightness) re
Summary of the content on the page No. 11
Figure 7 11
Summary of the content on the page No. 12
© 2003 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788 128-6653 12
