Metra Electronics 99-8710 user manual

Summary of the content on the page No. 1

INSTALLATION INSTRUCTIONS FOR PART 99-8710
APPLICATIONS
Mercedes C-Class 2001-2004
Mercedes CLK 2004
99-8710
KIT FEATURES
• DIN Radio Provision with Pocket
KIT COMPONENTS
A) Radio Housing
A
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver • Torx Screwdriver
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004-2008 METRA ELECTRONICS CORPORATION

Summary of the content on the page No. 2

99-8710 TABLE OF CONTENTS Dash Disassembly - Mercedes C-Class 2001-2004 .... ........ ....... ........ ........ ...1 - Mercedes CLK 2004 .... ........ ....... ........ ........ ....... ....2 Kit Assembly - DIN Mount Radio Provision ...... ....... ........ ........ .... ... ... 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 *Note: Refer also to the instructions included with the aftermarket radio. KNOWLEDGE IS POWER Enhance your installa

Summary of the content on the page No. 3

99-8710 DASH DISASSEMBLY MERCEDES C-CLASS 2001-2004 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unclip shifter trim (with gear indica- tors). Unclip and remove center console 3 trim panel. (Figure A) 4 Remove the ashtray insert by releas- ing (2) plastic clips on the bottom lip of the ashtray assembly. (Figure B) B 5 Using a small flat screwdriver push the lower clip (“A”) inward and rotate the vent upward to expose (1) Torx head screw. Loosen the To

Summary of the content on the page No. 4

99-8710 DASH DISASSEMBLY MERCEDES CLK 2004 *Note: Refer also to the instructions included with the aftermarket radio. 1 Disconnect the negative battery termi- A nal to prevent an accidental short cir- cuit. 2 Loosen shifter boot and pull up over shifter handle. (Figure A) 3 Turn the retainer on the shifter 1/2 turn to remove shifter handle and boot. (Figure B) 4 Unclip and remove the shifter trim panel. (Figure C) 5 Remove the ashtray insert by releasing (2) plastic clips on the bottom lip of

Summary of the content on the page No. 5

99-8710 KIT ASSEMBLY DIN MOUNT RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the appropriate bracket into the trim plate aligning the holes in the trim plate to the clips on the bracket. (Figure A) 2 Slide the DDIN radio unit into the trim plate bracket assembly and secure the unit to the kit using the screws sup- plied with the head unit. (Figure B) Continue to final assembly. B 3

Summary of the content on the page No. 6

99-8710 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas

Summary of the content on the page No. 7

99-8710 NOTES 5

Summary of the content on the page No. 8

99-8710 INSTRUCTIONS www.metraonline.com 1-800-221-0932 REV. 08/07/08 © COPYRIGHT 2004-2008 METRA ELECTRONICS CORPORATION INST99-8710