Summary of the content on the page No. 1
INSTALLATION INSTRUCTIONS FOR PART 99-7604
APPLICATIONS
INFINITI G35
2003-2004
99-7604/99-7604B/
99-7604T
KIT FEATURES
• DIN Radio Provision
• ISO Mount Radio Provision
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
• Painted To Match Factory Dash
99-7604= SILVER
99-7604B= BLACK
99-7604T=TAN
KIT COMPONENTS
A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Pocket • E) Double DIN Brackets
• F) Double DIN Trim Plate • G) Top Radio Housing Bracket • H) (2) #8 X
Summary of the content on the page No. 2
99-7604 TABLE OF CONTENTS Dash Disassembly - INFINITI G35 2003-2004 .... ........ ....... ........ ........ ....1,2,3 Kit Preparation . . . . . . . . . . . . . . ............................ ...... 4 Kit Assembly - DIN Radio Provision with Pocket ..... ....... ........ ....... . ......5 - ISO Mount Radio Provision with Pocket . . . .................... ...... 6 - Double DIN Radio Provision . ...... ....... ........ ........ ... .... .. 7 - Stacked ISO Units Provision ..... ........ ........
Summary of the content on the page No. 3
3 99-7604 DASH DISASSEMBLY INFINITI G35 2003-2004 1 Disconnect the negative battery ter- A minal to prevent an accidental short 1 circuit. 2 2 Unclip the collar below the shift knob and slide down. Using a small screw- driver or hook tool remove the spring clip to release and remove the shift knob. (Figure A) 3 Unclip the cup holder/shifter trim panel. Unplug and remove panel. B (Figure B) 4 Remove (2) Phillips screws from the bottom of the radio/climate control panel. (Figure C) 5 Remove (2) Ph
Summary of the content on the page No. 4
99-7604 DASH DISASSEMBLY INFINITI G35 2003-2004 8 Open glove box and remove (4) F Phillips screws from the top edge of box opening. (Figure F) 9 Unclip and remove the black cover panel below glove box and remove (1) Phillips screw from bottom of glove box exposed on left side next to accessory plug panel. 10 Remove (2) Phillips screws from the G accessory plug panel then unclip and remove the panel. (Figure G) 11 Unclip and remove the trim panel sur- rounding the clock and display on top of the
Summary of the content on the page No. 5
99-7604 DASH DISASSEMBLY INFINITI G35 2003-2004 K 14 Unsnap radio/climate control panel Remove (2) Phillips screws securing 16 including climate control vents at the the pocket to the radio/climate con- top left and right and pocket assem- trol panel and remove pocket. (Retain bly. Unplug and remove panel. pocket for use during kit assembly.) (Figure K) 17 Use (2) small flat blade screwdrivers 15 Remove (6) Phillips screws securing to gently pry the vents from radio/cli- the radio chassis to the
Summary of the content on the page No. 6
99-7604 KIT PREPARATION KIT PREPARATION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Attach the vents into the radio housing in the same location as the factory panel. (Figure A) 2 Secure the factory pocket removed in step 16 of the dash disassembly into the radio housing using the factory hardware. (Figure B) 3 Attach the top radio housing bracket to the radio housing using the (2) #8 X 3/8” Phillips screws provided with this kit. (Figure C) B 4 Clip the thin
Summary of the content on the page No. 7
99-7604 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) 3 Snap the pocket into the radio housing. (Figure C) Continue to final assembly. B C 5
Summary of the content on the page No. 8
99-7604 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the radio with the screws supplied with the radio. (Figure A) 2 Slide the radio into the radio housing until it snaps into place. (Figure B) 3 Snap the ISO trim plate onto the front of the Radio Housing. (Figure B) 4 Snap the pocket into the radio housing. (Figure C) B Continue to final assembly. C 6
Summary of the content on the page No. 9
99-7604 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the radio housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing. (Figure B) 3 Slide the Double DIN radio into the bracket/trim plate assembly and secure the radio to the assembly using the screws supplied with the radio. (Figure C) B 4 Snap the Double DIN trim plate into the radio housing. (Figure
Summary of the content on the page No. 10
99-7604 KIT ASSEMBLY STACKED ISO UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the radio housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing. (Figure B) 3 Slide the stacked ISO units into the bracket/radio housing assembly and secure the units to the kit using the screws supplied with the units. (Figure C) B 4 Snap the Double DIN trim plate into the radio housing. (Figure
Summary of the content on the page No. 11
99-7604 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas
Summary of the content on the page No. 12
99-7604 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 08/04/08 © COPYRIGHT 2008 METRA ELECTRONICS CORPORATION INST99-7604
