Metra Electronics 99-7509 user manual

Summary of the content on the page No. 5

99-7509 Dash Disassembly 4. Unclip and pull the center console towards the rear of the vehicle. Note: You do not have to remove the center console completely. (Figure E) 5. Remove (2) Phillips screws at the bottom of the radio trim panel then unclip the panel including the factory radio. Unplug and remove the panel. Note: The climate controls do not come out with the panel. (Figure F,G) (Figure E) Continue to kit assembly (Figure F) (Figure G) 5 A/C A/C

Summary of the content on the page No. 6

Kit Assembly 99-7509 DIN radio provision with pocket 1. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2. Slide the DIN cage into the radio housing and secure by bending the metal locking tabs outward. (Figure A) 3. Slide the aftermarket radio into the cage until it snaps into place. (Figure B) (Figure A) 4. Snap the pocket into t

Summary of the content on the page No. 7

Kit Assembly 99-7509 ISO mount radio provision with pocket 1. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2. Mount the ISO brackets to the aftermarket radio using the screws supplied with the radio. (Figure A) 3. Slide the radio into the radio housing until it snaps into place. (Figure B) (Figure A) 4. Snap the trim plate onto

Summary of the content on the page No. 8

Kit Assembly 99-7509 ISO mount radio provision with pocket 6. Snap the pocket into the radio housing. (Figure D) 7. Reassemble dash in reverse order of disassembly. (Figure D) 8

Summary of the content on the page No. 9

Kit Assembly 99-7509 Double DIN/Stacked ISO units provision 1. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2. Cut and remove the center bar from the radio housing. (Figure A) 3. Snap the double DIN brackets to the inside edge of the radio housing. (Figure B) (Figure A) 4. Slide the double DIN or stacked ISO unit(s) into the b

Summary of the content on the page No. 10

Notes

Summary of the content on the page No. 11

Notes

Summary of the content on the page No. 12

INSTALLATION INSTRUCTIONS FOR PART 99-7509 METRA. THE WORLD’S BEST KITS.™ metraonline.com 1-800-221-0932 © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION REV. 5/26/11

Summary of the content on the page No. 1

INSTALLATION INSTRUCTIONS FOR PART 99-7509
APPLICATIONS
Mazda 5 2006-up
(with manual climate controls)
99-7509
KIT FEATURES
• Painted to match factory dash
• DIN radio provision with pocket
• ISO radio provision with pocket
• Double DIN radio provision
• Stacked ISO mount units provision
KIT COMPONENTS
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
• C) Double DIN Trim Plate • D) Snap In Pocket
A B C
D
E F
WIRING & ANTENNA CONNECTIONS (Sold Separat

Summary of the content on the page No. 2

99-7509 Table of Contents Dash Disassembly – 2006-up Mazda 5 3-5 Kit Assembly – DIN radio provision with pocket 6 – ISO mount radio provision with pocket 7-8 – Double DIN/stacked ISO DIN head unit provision 9 Caution Metra recommends disconnecting the negative battery terminal before beginning any installation. All accessories, switches, and especially air bag indicator lights must be plugged in before reconnecting the battery or cycling the ignition. *NOTE: Refer also to the instructions

Summary of the content on the page No. 3

99-7509 Dash Disassembly 1. Remove the shifter. (Figure A) 2. Remove (2) Phillips screws exposed below shift lever trim panel. (Figure B) Continued on next page (Figure A) (Figure B) 3 A/C A/C P R N M-D

Summary of the content on the page No. 4

99-7509 Dash Disassembly 3. Unclip and remove the center console side trim panels then remove (1) Phillips screw per side behind panels. (Figure C,D). Continue to next page (Figure C) (Figure D) 4