Summary of the content on the page No. 1
INSTALLATION INSTRUCTIONS FOR PART 99-7423
APPLICATIONS
NISSAN Altima
2007-2011
99-7423
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
• A) Radio Housing • B) Radio Housing Trim Plate • C) Radio Housing Brackets
• D) Double DIN Trim Plate • E) Double DIN Brackets • F) ISO Brackets • G) Pocket
• H) (2) Climate Control Trim Panels • I) (2) #8 3/8” Screws
F
C
D E
B
Ha
Summary of the content on the page No. 2
99-7423 TABLE OF CONTENTS Dash Disassembly - NISSAN Altima 2007 -2011 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Kit Assembly - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - ISO Mount Radio Provision with Pocket . . . . . . . . . . .. . . . . . . . . . . . . . . . . . 4 - Double
Summary of the content on the page No. 3
99-7423 DASH DISASSEMBLY NISSAN ALTIMA 2007-2011 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unclip and remove trim panel between the shifter and the radio/ cli- mate control panel. (Figure A) 3 Remove (2) Phillips screws exposed behind panel below radio/climate control panel. (Figure A) 4 Unclip and remove the climate control vent trim panel then remove (2) B Phillips screws exposed behind panel. (Figure B) 5 Unclip, unplug and remove entire radio/cl
Summary of the content on the page No. 4
99-7423 KIT PREPARATION NISSAN ALTIMA 2007-2011 A 1 Clip the corresponding climate control trim panel into the radio housing. Note: There are (2) different climate control trim panels. One for auto cli- mate control and one for manual cli- mate control. (Figure A) 2 Attach the (2) radio housing brackets to the climate controls using the fac- tory screws. (Figure B) 3 Attach the bracket/climate control assembly to the radio housing using B the (2) #8 3/8” screws supplied with this kit. (Figure C)
Summary of the content on the page No. 5
99-7423 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) 3 Attach the radio housing trim plate supplied with the kit to the assembly. 4 Snap in the pocket into the assembly. B (Figure C) Continue to final assembly. C 3
Summary of the content on the page No. 6
99-7423 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the radio with the screws supplied with the radio. (Figure A) 2 Slide the radio into the radio housing until it snaps into place. (Figure B) 3 Attach the radio housing trim plate supplied with the kit to the assembly. (Figure B) 4 Snap the pocket into the assembly. B (Figure C) Continue to final assembly. C 4
Summary of the content on the page No. 7
99-7423 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the radio housing assembly. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing assembly. (Figure B) 3 Slide the Double DIN radio into the bracket/radio housing assembly and secure the radio to the assembly using the screws supplied with the radio. (Figure C) B 4 Snap the Double DIN trim plate onto the fr
Summary of the content on the page No. 8
99-7423 KIT ASSEMBLY STACKED ISO UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the radio housing assembly. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing assembly. (Figure B) 3 Slide the stacked ISO units into the bracket/radio housing assembly and secure the units to the kit using the screws supplied with the units. (Figure C) B 4 Snap the Double DIN trim plate onto the fron
Summary of the content on the page No. 9
99-7423 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disasse
Summary of the content on the page No. 10
99-7423 NOTES 8
Summary of the content on the page No. 11
99-7423 NOTES 9
Summary of the content on the page No. 12
99-7423 INSTRUCTIONS www.metraonline.com 1-800-221-0932 REV. 12/10/10 © COPYRIGHT 2007-2010 METRA ELECTRONICS CORPORATION INST99-7423
