Metra Electronics 99-7330 user manual

Summary of the content on the page No. 1

INSTALLATION INSTRUCTIONS FOR PART 99-7330
APPLICATIONS
KIA Spectra/Spectra 5
2007-2009
99-7330
KIT FEATURES
• Recessed DIN Mount
Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
KIT COMPONENTS
A) Radio Housing B) ISO Brackets C) Trim Plate
C
B
A
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
• 70-1004 - Hyundai 2006-up/KIA harness 2004-up
Antenna Adapter:
• Not required
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver

Summary of the content on the page No. 2

99-7330 TABLE OF CONTENTS Dash Disassembly - KIA Spectra/Spectra 5 2007-2009 .... ........ ....... ........ ........1 Kit Assembly - DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - ISO Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 *Note: Refer also to the instructions included with the aftermarket

Summary of the content on the page No. 3

99-7330 DASH DISASSEMBLY KIA SPECTRA/SPECTRA 5 2007-2009 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unclip and remove the trim panel sur- rounding the radio and including the a/c vents. (Figure A) Remove (4) Phillips screws securing 3 the radio. Unplug and remove radio. (Figure B) B Continue to kit assembly. 1

Summary of the content on the page No. 4

99-7330 KIT ASSEMBLY RECESSED DIN MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the DIN cage/housing assembly until it snaps into place. (Figure B) Continue to final assembly. B 2

Summary of the content on the page No. 5

99-7330 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Align the holes from the ISO snap in brackets with the holes in the side of the radio and mount the brackets to the radio using screws supplied with the radio. (Figure A) 2 Slide the radio/bracket assembly into the radio housing until the assembly snaps into place. (Figure B) 3 Snap the ISO trim plate onto the radio and housing assembly. (Figure B) B Continu

Summary of the content on the page No. 6

99-7330 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas

Summary of the content on the page No. 7

99-7330 NOTES 5

Summary of the content on the page No. 8

99-7330 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 06/24/09 © COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION INST99-7330