Summary of the content on the page No. 1
User Manual for Commercial Series Net DVR
Commercial Series Net DVR
User Manual
(V2.0)
Thank you for purchasing our embedded Net DVR. This manual is applicable for QSD42208,
QSC26408, and QSC26416 Net DVR, as well as the QSF2648008 and QSF2648016 Enterprise
DVR models. Please read this User Manual carefully to ensure that you can use the device
correctly and safely.
DISCLAIMER: The contents of this Manual are subject to change without notice; we are
also not responsible for typi
Summary of the content on the page No. 2
User Manual for Commercial Series Net DVR Index V ersion Description ........................................................................................................................... 4 Chapter 1 Product Introduction.................................................................................................. 6 1.1 Summary ................................................................................................................... 6 1.2 Features ..........................
Summary of the content on the page No. 3
User Manual for Commercial Series Net DVR 6.7 Mask Area Setup ..................................................................................................... 60 6.8 View Tampering Alarm ........................................................................................... 62 6.9 Video Loss Alarm .................................................................................................... 64 6.10 Motion Detection Alarm ........................................................
Summary of the content on the page No. 4
User Manual for Commercial Series Net DVR Version Description Version 2.0 built 070206: The new version firmware DVR has the following new features: 1. Supports USB mouse Recommended USB mouse model list: Logitech: M-UV83 Benq: M800 ViewSonic: MC204 Philips: SPM4500BB/93 LG: LGIM-ML208 GlodFly: GF-OP718 Newmen: MS0270 (www.newmen.com.cn) Agiler: AGM-018LU (www.agilertech.com) Citu: CH-3090 (www.citu.cn) 2. Supports USB external DVD backup Recommended USB external DVD m
Summary of the content on the page No. 5
User Manual for Commercial Series Net DVR If you select “Backup” mode, in DVR “Playback” menu, you can select SATA HDD for backup. 5．Solved some old version bugs VGA black screen and Aux audio output issues Page 5 Total 121
Summary of the content on the page No. 6
User Manual for Commercial Series Net DVR Chapter 1 Product Introduction 1.1 Summary The Commercial series network digital video recorder is an excellent digital surveillance product. It uses the embedded MCU and embedded operating system (RTOS), combining the most advanced technology in the Information Industry such as video and audio encoding/decoding, hard disk recording and TCP/IP. The firmware is burned into flash memory, more stable and reliable. The Commercial series device has bot
Summary of the content on the page No. 7
User Manual for Commercial Series Net DVR Preview and playback l Supports BNC analog moniotor and VGA output for main output l Supports one aux video and audio input l Supports multiple preview modes. l Supports sensitive area mask. l Supports camera spiteful block alarm. l Supports 2-ch synchronous playback. Support play forward, backward, pause, frame by frame, etc. l Supports play back by files or by time. l Displays local record status. PTZ l Supports many PTZ protocols. l Su
Summary of the content on the page No. 8
User Manual for Commercial Series Net DVR Chapter 2 Installation Warning: Before you install the DVR, please make sure the power to the DVR is switched off. 2.1 Checking the DVR and Its Accessories When you get the product, check that all the items are included in your product package. There is a list in the package. If any of the items are missing, please contact your dealer. 2.2 HDD Installation Installation notice The DVR has no HDD when leaving factory. Based on the record schedule,
Summary of the content on the page No. 9
User Manual for Commercial Series Net DVR 2.3 Rear Panel Description 2.3.1 8-ch QSD42208 Rear Panel Index Physical Interface Description Video Input Standard BNC. 1 Standard BNC. Loop Back Ports 2 Main video Output Connect CCTV monitor, output video and menu. 3 4 VGA Interface VGA display. RS-232/Keyboard Connect RS-232 devices. Refer to Appendix B for pin 5 definition. Interface Connect network devices. Refer to Appendix B for pin RJ45 Ethernet Port definition.
Summary of the content on the page No. 10
User Manual for Commercial Series Net DVR 2.3.2 8-ch/16-ch QSC26408/16 Rear Panel QSC26408 Rear Panel QSC26416 Rear Panel Index Physical Interface Description Video Input Standard BNC. 1 Audio Input Standard BNC. Aux video Output Spot monitor for video preview and playback. 2 Aux audio Output Spot monitor for audio preview and playback. Main video output Main monitor for video and menu. 3 Main monitor for audio preview and playback. Main audio output 4 Line In Audio line input
Summary of the content on the page No. 11
User Manual for Commercial Series Net DVR Connect network devices. Refer to Appendix B for pin RJ45 Network Port definition. USB memory disk, USB HDD, USB CD-R/W, USB DVD 7 USB Interface or USB mouse. st 8 E-SATA Optional. Extend 1 internal SATA to E-SATA. RS-485 terminal resistor switch. Default is off. The 9 SW1 resistor is 120Ohm. RS-485 PTZ connection. Using T+/T- to connect PTZ. Using D+/D- for keyboard and DVR cascade connection. Keyboard Interface Can use Hikvision DS-1000K
Summary of the content on the page No. 12
User Manual for Commercial Series Net DVR 2.4 External Alarm In/Out Connection Alarm input port (drp node): G (GND): Connect the GND of sensor. 1~8: Alarm input, support normal open/normal close. 0: Reserved. Alarm output: 1G~4G: 4 relay output. Alarm output connection Please note the usage of jumper JJ1. If you use DC, either connection is OK. We suggest you use DC under 12V, 1A. If you use AC, please open the jumper. There are 4 jumpers (JJ1, JJ2, JJ3 and JJ4) on DVR
Summary of the content on the page No. 13
User Manual for Commercial Series Net DVR Chapter 3 Operational Instructions 3.1.1 8-ch QSD42208 Front Panel Index Type Name Description 1 USB Port USB flash drive, HDD, DVDRW/CDRW or Mouse 2 Status 1-8 Shows channel 1-8 status. Green means recording; Red means Lamps network transmission; Orange means recording and network transmission. Lamp twinkle and red means the corresponding HDD has error. 3 POWER POWER Device switch with power indicator lamp. Green means DVR is
Summary of the content on the page No. 14
User Manual for Commercial Series Net DVR PREV 2. 【IRIS- 】in PTZ control. 1. Input switch (number, lower case, upper case and symbol); INFO 2. 【FOCUS+】in PTZ control; Main/Aux 3. In preview mode, display or hide the channel status bar. 1. Multi screen preview switch; 2. Switch menu mode into preview; 3. 【FOCUS- 】in PTZ control. 【ZOOM+】in PTZ control. 1. 【ZOOM-】in PTZ control. 2. Switch main/aux video output control mode. 5 Input Numeric Input number, lower case, upper case
Summary of the content on the page No. 15
User Manual for Commercial Series Net DVR 3.1.2 8-ch QSC26408 Front Panel Index Type Name Description 1 IR receiver. 2 Status 1-8 Shows channel 1-8 status. Green means recording; Red means Lamps network transmission; Orange means recording and network transmission. Lamp twinkle and red means the corresponding HDD has error. 3 Status 9-16 Shows channel 1-16 status. Green
Summary of the content on the page No. 16
User Manual for Commercial Series Net DVR 1. Local playback 2. 【AUTO】in PTZ mode. REC 1. Manual record; EDIT 2. 【SHOT 】in PTZ mode (adjust preset). 1. In edit state, delete current cursor character; PTZ 2. 【IRIS+ 】 in PTZ control; A 2. Select ü or × to enable or disable. 1. Enter into PTZ control mode; 2. 【IRIS- 】in PTZ control. PREV 1. Input switch (number, lower case, upper case and symbol); 2. 【FOCUS+】in PTZ control; INFO Main/Aux 3. In preview mode, di
Summary of the content on the page No. 17
User Manual for Commercial Series Net DVR 3.1.3 16-ch QSC26416 Front Panel Index Type Name Description 1 IR receiver. 2 Status 1-8 Shows channel 1-8 status. Green means recording; Red means Lamps network transmission; Orange means recording and network transmission. Lamp twinkle and red means the corresponding HDD has error. 3 Status 9-16 Shows channel 1-16 status. Green means recording; Red means Lamps network transmission; Orange means
Summary of the content on the page No. 18
User Manual for Commercial Series Net DVR EDIT 1. Manual record; 2. 【SHOT 】in PTZ mode (adjust preset). PTZ 1. In edit state, delete current cursor character; 2. 【IRIS+ 】 in PTZ control; A 3. Select ü or × to enable or disable. 1. Enter into PTZ control mode; PREV 2. 【IRIS- 】in PTZ control. 1. Input switch (number, lower case, upper case and symbol); INFO 2. 【FOCUS+】in PTZ control; Main/Aux 3. In preview mode, display or hide the channel status bar. 1. Multi sc
Summary of the content on the page No. 19
User Manual for Commercial Series Net DVR 3.2 Remote Control Index Name Description 1 POWER Turnoff device. 2 DEV Enable/Disable IR remote control 3 Numeric Keys Same as numeric keys of front panel. 4 EDIT Same as EDIT key of front panel. 5 A Same as A key of front panel. 6 REC Same as REC key of front panel. 7 PLAY Same as PLAY key of front panel. 8 INFO Same as INFO key of front panel. Same as [Main/Aux] key of front 9 VOIP panel. 10 MENU Same as MENU key of front panel. 11
Summary of the content on the page No. 20
User Manual for Commercial Series Net DVR 13 PTZ Same PTZ key of front panel. 14 ESC Same as ESC key of front panel. 15 Reserved 16 F1 Same as【F1】key of front panel. IRIS, FOCUS ZOOM for lens control 17 Lens control of PTZ camera. 18 F2 Same as【F2】key of front panel. Loading the batteries into the Remote Control 1. Remove the battery cover. 2. Insert the battery. Please make sure the poles (+ and -) are correctly positioned. 3. Replace the battery cover. Start to use the Remot
