Summary of the content on the page No. 1
4 CH Digital Multiplex Recorder
User Manual
Please read this instructions thoroughly before operation and keep the manual in a safe
place for further reference.
773 V 0.9
Summary of the content on the page No. 2
DMR WARNING All the safety and operating instructions should be read before operation. The improper operation may cause permanent damage. • Please use the provided adaptor (Other adaptor is not suitable for this machine). • Please lift and place this equipment gently. • Do not expose this equipment to open sunlight. • Do not use this equipment near water or in contact with water. • Do not spill liquid of any kind on the equipment. • Please power down the unit before unplugging. • Do not switch
Summary of the content on the page No. 3
DMR TABLE OF CONTENTS What do you get ? What do you get ? • FEATURES ---------------------------------------------------------------- ------------------------ 3 • PACKAGE CONTENT ---------------------------------------------------------------- ---------- 3 Before Operation Before Operation • INSTALLATION GUIDE ---------------------------------------------------------------- -------- 4 • FRONT PANEL ---------------------------------------------------------------- ------------------- 5 7 • BACK PA
Summary of the content on the page No. 4
What do you get ? FEATURES DVR Features l Wavelet compression format replaces Time-Lapse VCR + Multiplexer / Quad l 4 audio inputs / 2 audio outputs l On Screen Display and Remote Control via Video Server & PC l Picture-in-picture (PIP) in live l Motion detection & motion trigger recording function l Alarm input & output function l Video loss detected on each channel l Linear Zoom (2x~4x) l Multiplexer & Quad recording mode switching l Recording rate up to full size 30 images/sec. or Quad size
Summary of the content on the page No. 5
Before Operation INSTALLATION GUIDE 1. Connect cameras and monitor to the DVR. 2. Shown below is an example of connecting the DVR to your existing Observation System. 3. Install HDD (The compatible HDD Brands are listed in the following table.) Please refer to page.22 Appendix #1 for installation instructions. *The HDD must be installed before turning on the DMR, but if HDD is not installed, the DVR would be functioned as 4 CH multiplexer. COMPATIBLE HARD DISK MODELS Manufacturer Model Capacity
Summary of the content on the page No. 6
DMR FRONT PANEL 1. REMOVABLE HDD CARTRIDGE & KEYHOLE Please refer to page.22 Appendix #1. 2. LED LIGHT The LED Light is ON under following condition. • HDD : HDD status display • HDD Full : HDD is full • ALARM : To turn off the ALARM LED light, please refer to page.14 and set the ALARM mode as OFF. • TIMER : When Timer is set as Enabled • PLAY : On Playing mode • REC : On Recording mode 3. MENU Press MENU to enter main menu. 4. ENTER Press ENTER for confirmation. 5. SEARCH Press SEARCH for
Summary of the content on the page No. 7
11. REC Press REC to start recording. 12. PLAY Press PLAY to playback recorded video. 13. PAUSE / Up • Pause : Under DMR play mode, it can pause the action. • UP : Under setup mode, it works as Up button. 14. STOP / Down • STOP : Under DMR Record / Play mode, it can stop the moment action. • DOWN : Under setup mode, it works as Down button. 15. REW / Left • REW : Under DMR play mode, it can play video backward at different speeds. (Press REW again to adjust speed as 1, 2, 4, 8, 16, 32 times)
Summary of the content on the page No. 8
DMR REAR PANEL 1. P0WER Please use the provided power cord (The adaptor is embedded). 2. EXTERNAL I/O • Controlled remotely by an external device or control system like Video Web Server. • Alarm input, external I / O explanation. 3. VIDEO INPUT (1-4) Connect to video source, such as camera. 4. MAIN Connect to Main monitor. 5. CALL Connect to CALL monitor. Show the Switch Display. When alarm trigger happens, the call monitor will show the triggered channel for a period of time. 6. AUDIO IN (1-4
Summary of the content on the page No. 9
Basic Operation GETTING STARTED Before using the DMR, please have a HDD installed ready, or it will be functioned as 4 CH multiplexer (refer to Appendix #1 for installation or removal of a HDD). 1. Connect the AC Power Cord and plug into an electrical outlet then press the power switch “ON”. The Red LED indicator light will be ON and the DMR is in Standby mode. 2. Press the Power button. The POWER LED will turn from red to orange, and other red LED indicators will turn ON. It takes approximat
Summary of the content on the page No. 10
PLAY BACK Press “ PLAY ” button, the DMR will show the last recording. 1. FAST FORWARD (F.F.) & FAST REWIND (F.R.) You can increase the speeds of Fast Forward and Rewind on the DMR. In the Play mode, press ” ► ” once to get 2X speed forward and press twice to get 4X speed,… and the maximum speed can reach 32X. Press ”◄ ” once to get 1X speed rewind and press twice to get 2X speed, … and the maximum speed can reach 32X. 2. SLOW FORWARD (S.F.) & SLOW REWIND (S.R.) You can also slow down the sp
Summary of the content on the page No. 11
Detailed Menu Setup MAIN MENU There are 12 options available in the Main Menu: (MENU) TIMER TIMER ---------- Programs Specific Time to Record CAMERA CAMERA ------- Camera Channel Setup RECORD RECORD ------- Record Mode Setup ALARM ALARM --------- Alarm Setup DWELL DWELL --------- Dwell time Setup PIP PIP --------------- Picture in Picture Setup MOTION MOTION -------- Motion Detection Setup DISPLAY DISPLAY ------- Display Mode Setup REMOTE REMOTE ------- Remote Control Setup USER USER -------
Summary of the content on the page No. 12
DMR MENU OPTIONS SYSTEM (MENU) TIMER 1. AUDIO INPUT CAMERA RECORD To choose one of 4 channels to record. (It can only record 1 input) ALARM DWELL 2. BUZZER PIP Set the BUZZER “ON”, it will buzzer by event occurrence when the setting is ON. MOTION 3. EXT ALARM DISPLAY To set the EXTERNAL AUDIBLE ALARM. It will be trigged by event occurrence REMOTE when the setting is ON. USER SYSTEM 4. VLOSS ALARM EVENT To set the VLOSS ALARM. When the setting is “ON”, the alarm will occurrence by the setti
Summary of the content on the page No. 13
TIMER 1. DAY Select the day, or days of the week (Mon–Fri / Sat-Sun / Daily) that you wish to schedule (MENU) the DMR to automatically record. TIMER CAMERA NOTE : RECORD 1. Special Date could be changed by “+” and “-” buttons. ALARM DWELL 2. If you have selected the specific date and recording timer set from that specific day PIP to a new day, then the Recording Timer Schedule will be set as whole week. For MOTION specific date of Recording Timer Schedule, it is not recommended to set End Time
Summary of the content on the page No. 14
CAMERA 1. TITLE (MENU) TIMER Assign a title to each camera. Initially each title is the camera’ s number. CAMERA RECORD 2. ALARM ALARM Select LOW / OFF / HIGH for alarm polarity. The default value is LOW. DWELL TITLE ALARM REC BR CT CL HUE PIP MOTION CAMERA 1 LOW ON 18 15 15 18 DISPLAY CAMERA 2 OFF OFF 18 15 15 18 REMOTE USER CAMERA 3 HIGH OFF 18 15 15 18 SYSTEM CAMERA 4 HIGH ON 18 15 15 18 EVENT 3. RECORD (REC) Set up which channel you want to record. ON : when alarm input is triggered, D
Summary of the content on the page No. 15
ALARM (MENU) 1. ALARM ENABLE TIMER To set the ALARM ENABLE. It will be triggered by event occurrence when the CAMERA setting is ON. RECORD ALARM 2. ALARM DURATION DWELL Set the reaction time which was determined by how long the alarm mode PIP responded to a buzzer. Default setting is 10 sec. Options are 10 SEC, 15 SEC, 20 MOTION SEC, 30 SEC, 1 MIN, 2 MIN, 3 MIN, 5 MIN, 10 MIN, 15 MIN, 30 MIN, ALWAYS, AUTO. DISPLAY REMOTE 3. REC IPS USER Select the images per second of recording during an
Summary of the content on the page No. 16
MOTION (MENU) 1. SEN (Sensitivity) TIMER Sets the sensitivity of the Pixel-based Motion Detection feature from 1fo 70. CAMERA RECORD 2. MD-NVM ALARM Sets the number of targets in which Motion must occur in order to trigger an Alarm DWELL (from 1-99 target areas). PIP Note: MD-NVM cannot be less than the number of targets set in the AREA. MOTION DISPLAY 3. RE REMOTE Sets the Reference image to which the current screen is compared (from 1-99). USER th For example, the value 64 would compare
Summary of the content on the page No. 17
7. DAY / START / END To setup the DAY and the START/ END time for motion trigger recording timer setting. Figure 1-1 Figure 1-2 MOTION DETECTION SETUP MOTION DETECTION SETTING — ROW SETUP 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 11 11 12 12 Figure 1-3 Figure 1-4 MOTION DETECTION TRIGGERED-TURN INTO PURPLE BACK TO MOTION DETECTION SETTING 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 1
Summary of the content on the page No. 18
5. LOSS SCREEN (DISPLAY) Retain the last picture or select the LOSS SCREEN color. TITLE DISPLAY YES OSD COLOR YELLOW The options are GREEN, BLACK, BLUE. BORDER TYPE 4/2 BORDER COLOR WHITE LOSS SCREEN GREEN 6. OSD POSITION OSD POSITION NORMAL To set the OSD POSITION shown on monitor. The options are NORMAL or CENTER. (MENU) TIMER REMOTE CAMERA RECORD 1. REMOTE MODE ALARM Set the remote mode for connectio
Summary of the content on the page No. 19
EVENT A single page can display 16 recorded events. Press “◄ ” or “► ” to change the (MENU) pages or press ▲ + ▼ to CLEAR the EVENT record. TIMER CAMERA RECORD DISK FULL: HDD is full ALARM PWR REST : Power restored DWELL PIP M-HD REMS: HDD remove MOTION M-HD REPL: HDD replace DISPLAY REMOTE M-HD ERR : HDD error USER M-HD WARM: HDD warning SYSTEM EVENT K UNLOCKS: Key is unlock DMA ERROR: DMA error C1 VLOSS : Camera 1 is video loss C1 VLOSS 26-DEC-2002 03:00:00 C2 ALARM 26-DEC-2
Summary of the content on the page No. 20
Advanced Operation OPERATION OPTIONS ZOOM Press ZOOM button to enlarge the display of main picture. It displays zoomed picture on main picture and a small window inserted. The inserted window contains a movable 1/4 view size of the appointed camera. The range is from 2X to 4X. •Press PIP : Zoom in •Press QUAD : Zoom out •Press the “Zoom” button again to leave the zoom pointer. •Press Camera (1-4) to select channel. •Press ▲▼ ◄► to move the zoom position. VIDEO LOSS Screen will display ‘ LOSS”
