Summary of the content on the page No. 1
MODEL G0706
12" PARALLELOGRAM
JOINTER
OWNER'S MANUAL
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Table of Contents INTRODUCTION ............................................... 2 SECTION 5: ACCESSORIES ......................... 28 SECTION 6: MAINTENANCE ......................... 30 SECTION 1: SAFETY ....................................... 6 SECTION 7: SERVICE ................................... 31 SECTION 2: CIRCUIT REQUIREMENTS ........ 9 SECTION 3: SETUP ....................................... 10
Summary of the content on the page No. 4
INTRODUCTION Manual Accuracy Contact Info your machine may not exactly match the manual Machine Description www.grizzly.com
Summary of the content on the page No. 5
Identification To reduce the risk of serious injury when using this machine, read and understand this entire manual before beginning any operations.
Summary of the content on the page No. 6
MACHINE DATA SHEET MODEL G0706 12" X 60" SHORT BED JOINTER W/ SPIRAL CUTTERHEAD Product Dimensions: Shipping Dimensions: Electrical: Motors: Main Main Specifications: Cutting Capacities
Summary of the content on the page No. 7
Fence Information Cutterhead Information Table Information Construction Table Information Other Information Other Specifications: Features:
Summary of the content on the page No. 8
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indicat
Summary of the content on the page No. 9
Safety Instructions for Machinery 7. ONLY ALLOW TRAINED AND PROP- 16. REMOVE CHUCK KEYS OR ADJUSTING ERLY SUPERVISED PERSONNEL TO TOOLS. OPERATE MACHINERY. 17. DAMAGED MACHINERY. 8. KEEP CHILDREN/VISITORS AWAY. 18. DO NOT FORCE MACHINERY. 9. UNATTENDED OPERATION. 19. SECURE WORKPIECE. OFF 10. DO NOT USE IN DANGEROUS 20. DO NOT OVERREACH. ENVIRONMENTS.
Summary of the content on the page No. 10
Additional Safety for Jointers 1. JOINTER KICKBACK. 6. MAXIMUM CUTTING DEPTH. 7. JOINTING WITH THE GRAIN DO NOT 2. CUTTERHEAD ALIGNMENT. 8. KEEPING GUARDS IN PLACE. 3. PUSH BLOCKS. 9. PROPER CUTTING. 4. WORKPIECE SUPPORT. 10. USING GOOD STOCK. 5. KICKBACK ZONE.
Summary of the content on the page No. 11
SECTION 2: CIRCUIT REQUIREMENTS Power Connection Device 220V Single-Phase Operation Figure 1 Serious personal injury could occur if you connect the machine to power before com- pleting the setup process. DO NOT connect the machine to the power until instructed later in this manual. Electrocution or fire could result if machine is not Figure 1. correctly grounded or connected to the power Extension Cords source. Get help if you do
Summary of the content on the page No. 12
SECTION 3: SETUP Items Needed for This machine presents Setup serious injury hazards to untrained users. Read through this entire manu- al to become familiar with the controls and opera- tions before starting the machine! Description Qty Wear safety glasses dur- ing the entire setup pro- cess! Page 33 The Model G0706 is a heavy machine (834 lbs Unpacking shipping weight). Use power lifting equipment to lift th
Summary of the content on the page No. 13
Hardware and Tools (Figure 4) Qty Inventory Note: If you can't find an item on this list, check the mounting location on the machine or examine the packaging materials carefully. Occasionally we pre-install certain components for shipping purposes. Crate Contents: (Figure 2 & 3) Qty A. B. C. D. Figure 4. Figure
Summary of the content on the page No. 14
Hardware Recognition Chart
Summary of the content on the page No. 15
Cleanup Gasoline and petroleum products have low flash points and can explode or cause fire if used to clean machinery. Avoid using these products to clean machinery. Many cleaning solvents are toxic if inhaled. Minimize your risk by only using these products in a well ventilated area. NOTICE Avoid chlorine-based s
Summary of the content on the page No. 16
Site Considerations Weight Load Physical Environment Machine Data Sheet Space Allocation Electrical Installation See below for required space allocation. Lighting Children or untrained people may be seriously injured by this machine. Only install in an access restricted lo
Summary of the content on the page No. 17
Moving & Placing Mounting to Shop Base Unit Floor The Model G0706 is a heavy machine. Serious personal injury may occur if safe moving meth- ods are not used. To be safe, get assistance and use power equipment to move the shipping crate Bolting to Concrete Floors and remove the machine from the crate. Figure 8 To lift the jointer
Summary of the content on the page No. 18
3. Assembly Figure 11 To assemble the jointer: 1. Figure 11. 4. Figure 12 Figure 9. 2. Figure 12. 5. Figure 10 Figure 13 Figure 10. Figure 13.
Summary of the content on the page No. 19
8. Figure 15 Setting Outfeed Table Height Page 33 The outfeed table height MUST be set level with the cutting inserts when they are at Figure 15. top-dead-center or the workpiece cannot safely feed across the jointer, which will 9. increase the risk of a kickback injury. 6. 10. Figure
Summary of the content on the page No. 20
Dust Port Test Run DO NOT operate the Model G0706 with- out an adequate dust collection system. This machine creates substantial amounts Troubleshooting Page 31 of wood dust while operating. Failure to use a dust collection system can result in short and long-term respiratory illness. Recommended CFM at Dust Port: .....615 CFM To test run the machine: Do not confuse this CFM recommendation with the rating of the dust collector. To deter
