Summary of the content on the page No. 1
INSTALLATION / OPERATION
EDR-910A
9-channel Digital Video Recorder
EDR-910D
9-channel Digital Video Recorder
with internal DVD-RW drive
EDR-1610A
16-channel Digital Video Recorder
EDR-1610D
16-channel Digital Video Recorder
with internal DVD-RW drive
Summary of the content on the page No. 2
Safety warnings Safety warnings To avoid any damage, please consider the following safety warnings: Never place the recorder near to heaters, furnaces, other heat sources or under direct solar irradiation. Operate the device only in locations providing the tolerable operating temperature range 0°C~40°C. Make sure that the device‘s ventilation slots are not covered or sheeted. For cleaning, make sure the device is plugged off and only use a damp cloth without acid dete
Summary of the content on the page No. 3
Summary of the content on the page No. 4
6. VIDEO EXPORT .........................................................................................- 58 - 7. CALL MONITOR SETUP..............................................................................- 60 - 8. DISPLAY SETTINGS ..................................................................................- 61 - 8.1. BRIGHTNESS, CONTRAST, COLOUR....................................................- 61 - 8.2 IMAGE POSITION ADJUSTMENT ON MONITOR ....................................
Summary of the content on the page No. 5
INTRODUCTION 1. INTRODUCTION The latest EverFocus digital video recorder generation is based on MPEG-4 compression technology, resulting in enhanced recording capacity and improved network image transmission speed with high image quality. Comprehensive features and extended event recording settings enable the almost universal application of this DVR series. 1.1 FEATURES • Duplex operation: simultaneous recording and playback • MPEG4 compression method with configurable qualit
Summary of the content on the page No. 6
1.3 TECHNICAL DATA Video format PAL EDR 910: 9 x 1 Vpp FBAS, BNC, 75 Ohm Video input EDR 1610: 16 x 1 Vpp FBAS, BNC, 75 Ohm Main monitor: 1 Vpp FBAS, BNC at 75 Ohm Video output Callmonitor: 1 x 1 Vpp FBAS, BNC at 75 Ohm 9/16 x loop-through outputs 1 Vpp FBAS, BNC at 75 Ohm Video compression MPEG-4 Recording resolution 720 x 288, 720 x 576 or 360 x 288 Main monitor: full screen, PiP, 4,7,9,10*,13*,16*, 2 x zoom, sequence Display modes Call monitor: full screen, sequence (*only E
Summary of the content on the page No. 7
Power consumption 50 W max. Dimensions 430 (W) x 72 (H) x 402,5 (D) mm Weight 6,42 kg Ambient temperature 0°C ~ +40°C Remote control Optional: IR remote control, RS-485 keyboard EDR910 -7 - _1610_ma_en_rev1 00
Summary of the content on the page No. 8
1.4 FRONT PANEL OPERATING ELEMENTS Keys (1) REC: recording key (2) STOP: recording / playback stop (3) PLAY: playback (4) PAUSE: image freeze, stops playback for freeze mode (5) SEARCH: opens on-screen display for playback search (6) COPY: opens image export menu. In playback mode, the current playback position is stored as image export start position. (7) ENTER: Enter key for input confirmation (8) DISPLAY: main monitor status display swit
Summary of the content on the page No. 9
(11) ZOOM: In full screen mode: 2x electronical zoom. Zoom screen can be moved through JOG. ENTER key changes the direction. Further zoom key actuation switches the electronical zoom off. In multiscreen mode: Image orientation adjustment. Use the JOG to adjust the image to the respective monitor type. ENTER switches between horizontal and vertical adjustment. Further ZOOM key actuation switches the adjustment off. (12) SEQ: Sequence operation, automatic image switching (13) CAL
Summary of the content on the page No. 10
1.5 CONNECTIONS (1) Main switch: Power switch, below IEC socket for 100~240 VAC power source (2) MAIN monitor: Main monitor for live and playback display and on-screen display (3) CALL monitor: CALL monitor output. Spotmonitor for full screen live display, sequence mode and alarm camera switching (4) Video inputs: EDR910: VIDEO IN(1~9): BNC video inputs for 1 Vpp Composite video signals, automatic 75 Ohm termination (high impedance switching upon loop-through output lo
Summary of the content on the page No. 11
1.6 SCREEN DISPLAYS Here’s an overview of the screen displays appearing on the MAIN monitor: 1. Channel display 2. Event (here: video loss) 3. Display selection 4. Playback status 5. Recording status (1) Channel display: shows the selected video channel’s description (2) Event: Event display, may be channel-related or global Channel-related types of event: Alarm: Display of an alarm triggered by alarm input contact A Motion: Motion detection of the respective
Summary of the content on the page No. 12
(3) SELECT: Within a multiscreen view, the SELECT key activates the camera selection mode. The active camera field shows “S”. Use the JOG to switch between the camera fields. Use the channel keys 1~9 or 1~16 to switch the channel. (4) PLAYBACK STATUS: The playback-relevant information are displayed in this status bar. Playback date Playback status Playback 1. Playback date: Current playback date 2. Playback status: Playback operati
Summary of the content on the page No. 13
INSTALLATION 2. INSTALLATION ATTENTION: The installation should be effected by qualified personnel only. Connect power source only after having finished the further installation. 2.1 Delivery scope Check the delivery scope (see 4.) before starting the installation. 2.2 Video connection installation Sample installation with maximum camera and monitor configuration: Cameras and monitors have to be cabled with 75 Ohm video cable, e.g. RG-59, RG-12 and suitable BNC p
Summary of the content on the page No. 14
2.3 RS-485 keyboard installation All EDR910/1610 functions can be remote-controlled by the EKB 500 universal keyboard. Using the EEPbus protocol, digital video recorders, keyboards and speed domes can be installed on one single RS-485 bus. One system can comprise up to 8 keyboards. 2.3.1 General RS-485 bus installation EKB-500 uses an RS-485 simplex wiring; the signal is transferred via a single twisted pair line. CAT5 network cable is recommended, UPT version (unshielded)
Summary of the content on the page No. 15
If star wiring is inevitable, EDA 997A RS-485 signal distributors may be used. The maximum system cable length can also be expanded by using these distributors, physically providing a new RS-485 bus with 1200 m cable length each at every distributor output. Star wiring with RS-485 signal distributor In case the maximum number of 32 bus participants is exceeded, the number of connected devices can be increased by using RS-485 distributors. Each distributor output physically provides
Summary of the content on the page No. 16
2.3.2 RS-485 plug connection assignment The two RS-485 input RJ-45 plugs are looped through and pin-compatible. The following RJ-45 plug assignment has to be considered for connection: Pin 3: RS-485 + Pin 6: RS-485 - The following illustration shows the connector box assignment of the optional EDA998 connection kit (connector box, patch cable): 2.3.3 EKB-500 connection with network patch cable For a simple, short distance installation, recorder and keyboard can directly
Summary of the content on the page No. 17
2.3.4 EKB-500 connection to several DVRs For long distance installations connecting several DVRs, the use of the optional EDA998 connection kit is recommended: EKB 500 installation with several DVRs and EDA998 connection kit For further details on keyboard connection, please refer to the EKB 500 manual. RS-485 port communication settings are configured in the RS-232/485 menu. EDR910 - 17 - _1610_ma_en_rev1 00
Summary of the content on the page No. 18
2.4 Speed dome installation Speed dome or telemetry receiver pan/tilt/zoom control is available through web browser or the optional PowerCon software if the DVR is connected to a network. Local telemetry control is provided by the optional EKB 500 keyboard. ATTENTION: The basic RS-485 wiring rules described in chapter 2.3.1. also apply to the connection of speed domes or telemetry receivers. Supported protocols: EverFocus, ED2200/2250, Pelco-D, Pelco-P The optional RS-485 connec
Summary of the content on the page No. 19
Summary of the content on the page No. 20
2.6 PS/2 mouse installation EDR910/1610 may optionally be controlled through USB wheelmouse which must be connected before system start-up. The mouse connector is the lower USB socket at the front panel. 2.7 Network connection EDR910/1610 DVRs provide fast MPEG-4 format image transmission and network remote configuration. This chapter doesn‘t go into basic network technique details. For further information, especially about router installation and internet connection, ple
