Summary of the content on the page No. 1
User Manual
ECOR264-4F1/ECOR264-4D1
ECOR264-4F1/ECOR264-4D1
ECOR264-8F1/ECOR264-8D1
ECOR264-8F1/ECOR264-8D1
Summary of the content on the page No. 2
E V E R F O C U S E L E C T R O N I C S C O R P O R A T I O N ECOR264-4F1/ ECOR264-4D1 ECOR264-8F1/ ECOR264-8D1 Instruction Manual 2009 EverFocus Electronics Corp www.everfocus.com All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form or by any means without written permission of the Everfocus Electronics Corporation. Release Date: Nov. 2009 QuickTime is a registered trademark of the Apple Computer,
Summary of the content on the page No. 3
Safety Precautions Refer all work related to the installation of this product to qualified service personnel or system installers. Do not block the ventilation opening or slots on the cover. Do not drop metallic parts through slots. This could permanently damage the appliance. Turn the power off immediately and contact qualified service personnel for service. Do not attempt to disassemble the appliance. To prevent electric shock, do not remove screws or covers. There
Summary of the content on the page No. 4
Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards. Water and Moisture Do not use this unit near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, near a swimming pool, in an unprotected outdoor installation, or any area which is classified as a wet location. Servicing Do not attempt to service this unit by yourself as opening or removing covers may expose you to dangerous vo
Summary of the content on the page No. 5
WEEE This Product is RoHS compliant. The information in this manual was current upon publication. The manufacturer reserves the right to revise and improve his products. Therefore, all specifications are subject to change without prior notice. Manufacturer is not responsible for misprints or typographical errors. Please read this manual carefully before installing and using this unit. Be sure to keep it handy for later reference.
Summary of the content on the page No. 6
TABLE OF CONTENTS 1 PRODUCT OVERVIEW ..................................................................................................... 1 1.1 FEATURES ....................................................................................................................... 1 1.2 PACKAGE CONTENTS................................................................................................... 2 1.3 SPECIFICATIONS ...........................................................................
Summary of the content on the page No. 7
3.6.1 General PTZ control (if PTZ cameras are installed) ........................................................................22 3.6.2 Express Control of PTZ.........................................................................................................................23 3.7 LAYOUT......................................................................................................................... 25 3.7.1 Bring to full screen mode ............................................
Summary of the content on the page No. 8
4.9.5 Misc. ......................................................................................................................................................80 4.10 INFORMATION........................................................................................................... 81 4.10.1 System....................................................................................................................................................81 4.10.2 Log.............................
Summary of the content on the page No. 9
Chapter 1 1 PRODUCT OVERVIEW This new EverFocus digital video recorder is based on H.264 compression technology, resulting in increased recording capacity and improved network image transmission speed while retaining high image quality. Comprehensive features and extended event recording settings enable the almost universal application of this DVR. The ECOR264-4/ECOR264-8 DVR permits multiple control inputs. These inputs include mouse control, front panel control, IR remote control and
Summary of the content on the page No. 10
1.2 PACKAGE CONTENTS Digital Video Recorder x1 User Manual x 1 AC Adapter and Power Cord x1 Mouse x 1 2
Summary of the content on the page No. 11
1.3 SPECIFICATIONS Number of Channels 4 8 Compression Format H.264 120 NTSC / 100 PAL (CIF) 120 NTSC / 100 PAL (CIF) Recording & Playback 60 NTSC / 50 PAL (Half D1) 60 NTSC / 50 PAL (Half D1) Rate/Resolution 30 NTSC / 25 PAL (D1) 30 NTSC / 25 PAL (D1) Pentaplex Operation Simultaneous Live, Recording, Playback, Archive and Remote Viewing Video Inputs 4 BNC Composite 8 BNC Composite Main Monitor Outputs 1 BNC Composite, 1 VGA Audio Input/Output 1 Input / 1 Output 10KΩ/500mV P-P R
Summary of the content on the page No. 12
1.4 FRONT PANEL Your primary interaction with your new DVR will be through the Front Panel buttons and their corresponding buttons on the included Remote Control. Take a moment to learn where the keys are as the remainder of the manual will refer to them often. Figure 1-1 Front Panel 1) IR Receiver: Receiver for IR remote control 2) Live: Press this key to show live view. Press to exit from playback mode. 3) View: Press this key to switch between 4x, PiP (Picture In
Summary of the content on the page No. 13
6) ◄◄/◄I: Fast reverse playback or step reverse playback depending on playback mode. 7) ◄/ I I: Reverse playback or pause 8) ►/ I I: Forward playback or pause 9) ►►/I►: Fast Forward playback or step forward playback depending on playback mode. 10) DVD+RW: DVD+RW burner (D models only) 11) POWER LED: This LED ON indicates Power on. 12) ALARM LED: This LED ON indicates Alarm active. 13) HDD LED: This LED ON indicates HDD active. 14) Net LED: T
Summary of the content on the page No. 14
1.5 REAR PANEL During initial setup you will be connecting your DVR to multiple input and output devices. This is done through the rear panel. 3 5 7 8 9 10 11 ○ ○ ○ ○ ○ ○ ○ 1 2 4 6 ○ ○ ○ ○ Figure 1-2 Rear Panel 1 ○ ○ ○ ○ POWER: Plug the DC 12V power source provided into the power socket. 2 ○ ○ Alarm In: Connect up to 4 alarm inputs, selectable between N.O./N.C. contacts or can accept ○ ○ TTL/CMOS signal polarity. 3 ○ ○ ○ ○ Alarm Out: N.C or N.O type alarm out (form “C”).
Summary of the content on the page No. 15
11 ○ ○ ○ ○ LAN: RJ-45 network connection 10/100Mb/s Ethernet. There are two LEDs on the LAN jack; Green LED means network is connected, amber LED flickers when data is being exchanged. 1.6 VIDEO INPUTS/OUTPUTS INSTALLATION Camera and CCTV monitor must use 75 Ohm video cable (e.g. RG-59, RG-6, RG-11) with BNC connectors. To avoid impedance mismatch and undesired loss/reflections, 50 Ohm coax cable (e.g. RG-58), antenna cable and other types of coaxial cable are not compatible. Al
Summary of the content on the page No. 16
1.8.1 Alarm Input Contacts This DVR provides one alarm input per camera. All inputs are programmable N.O. (Normal Open) or N.C. (Normal Closed) Inputs have to be switched by dry contacts. Alarm input with N.O. (Normal Open) contact Alarm input with N.C. (Normal Closed) contact in idle state in idle state All settings are programmed in the ALARM menu (Section 0). 1.8.2 Alarm Output Relay The relay output provides either Normally Open or Normally Closed dry contacts.
Summary of the content on the page No. 17
Cable length from box to device („Stubs“) has to be limited to 2m using connector boxes. RS-485 bus serial wiring with connector boxes and connection cable A direct RS-485 bus star wiring is not supported unless using a signal distributor (see below). Improper RS-485 bus star wiring A RS-485 signal distributor may be used to use a star wiring configuration. Star wiring with RS-485 signal distributor A RS-485 distributor can also be used to increase the maximum numb
Summary of the content on the page No. 18
System expansion with RS-485 signal distributor ATTENTION: Most signal distributors are unidirectional! This means that the signal only flows from the input towards the outputs. Therefore, e.g. the interconnection of several keyboards is not possible with these types of signal distributor! 1.9.2 RS-485 socket pin assignment The RS485 pin assignment is as follows: 1.9.3 EKB-500 connection with network patch cable For a simple, short distance installation, recorder and keyboard
Summary of the content on the page No. 19
1.10 USB-Mouse installation Connect the USB mouse to one of the 2 USB ports. (This can be done while DVR is powered on) The rear USB V1.0 port is recommended to reserve the higher speed front USB V2.0 port for video copy/export. NOTE: Recommended mouse types are Logitech® and Microsoft® wired USB wheel-mouse. Wireless USB mouse is not supported. 1.11 NETWORK CONNECTION This section only describes physical connection to an Ethernet network. This step must be completed before the
Summary of the content on the page No. 20
1.11.2 Network Connection through Patch Cable The connection to an existing network requires a normal patch cable (straight-through). The illustration shows the connection to a network switch or router. Figure 1-4 Network Connection through Patch Cable Pinout of straight patch cable 1.12 FINAL INSTALL PROCESS Once you have completed the basic wiring connections, you are ready to turn on the DVR. Simply plug in the power source. The POWER LED will light up if power is norma
