Summary of the content on the page No. 1
Summary of the content on the page No. 2
Important Safeguards and Precautions TO REDUCE THE RISK OF ELECTRIC SHOCK, FIRE, INJURY TO PERSONS OR DAMAGE TO THIS PRODUCT, READ AND RETAIN ALL SAFETY AND OPERATING INSTRUCTIONS. HEED ALL WARNINGS IN THE MANUAL AND ON THE PRODUCT. INSTALLATION OUTDOOR ANTENNA INSTALLATION 1 SAFE ANTENNA AND CABLE CONNECTION 1 POWER SOURCE CAUTION If an outside antenna or cable system is connected to the equipment, be sure the Operate only from a power source indicated on the unit or in this antenna or cable s
Summary of the content on the page No. 3
Summary of the content on the page No. 4
R R Before Using Congratulations Head Cleaning on your purchase of one of the most Playing older or damaged tapes may eventually sophisticated and reliable products on the cause video heads to become clogged. market today. Used properly, it will bring you Video Head Clog Sensor years of enjoyment. Please fill in the information V I DEO HEADS MAY below. The serial number is on the tag located NEED CLEAN I NG During playback, this screen PLEASE I NSERT HEAD on the back of your DECK. CLEAN I
Summary of the content on the page No. 5
Initial Setup Basic VCR DVD For Your (Connection) Operation Operation Operation Information Table of Contents Initial Setup (Connection) DVD / VCR Important Safeguards and Precautions ......................... 2, 3 Before Using ......................................................................... 4 DECK & Cassette Information ........................................ 6 , 7 Location of Controls .................................................... 8 ~ 10 Displays (On Screen Displays and Multi F
Summary of the content on the page No. 6
DECK & Cassette Information DVD-RAM discs Prevent Accidental Tape Erasure DVD-RAM discs must meet the following conditions Break off the tab to for this unit to be able to play them. prevent recording. Non-cartridge discs Record Tab Type Discs that can be removed from Screw driver their cartridges (TYPE 2 and 4) 12 cm (5”) 9.4 GB (double-sided) Capacity and 4.7 GB (single-sided) 8 cm (3”) 2.8 GB (double-sided) To record again Remove TYPE 2 and 4 discs from their cartridges Cover the ho
Summary of the content on the page No. 7
Initial Setup (Connection) Specifications Power Source: 120 V AC, 60 Hz Power Consumption: Power On: Approx. 28 watts, Power Off: Approx. 0.85 watts Video Signal: EIA Standard NTSC color Video Recording System: 4 rotary heads helical scanning system Audio Track: 1 track (Normal), 2 channel (Hi-Fi Audio Sound) Tuner Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69 CABLE Channels: Midband A through I (14 ~ 22), Superband J through W (23 ~ 36) Hyperband AA ~ EEE (37 ~ 64), Lowband A-5 ~ A-1 (95 ~ 99)
Summary of the content on the page No. 8
Summary of the content on the page No. 9
Initial Setup (Connection) If the disc cannot be removed... Front View of DECK Front View of DECK First, unplug DECK. Then, prepare a rigid Bold: VCR Function wire (e.g. an extended paper clip) and, Italic: DVD Function applying moderate force, insert it straight Bold Italic: VCR and DVD Functions into the hole at the base of the tray. Normal: Others The tray will eject a little. Now, pull the tray all the way out and remove the disc. PLAY p. 20 STOP/EJECT Over 2 inches p. 20 Remote Cassette Dis
Summary of the content on the page No. 10
Summary of the content on the page No. 11
Initial Setup (Connection) Displays (On Screen & Multi Function) On Screen Displays (VCR) Function & Channel Displays Blank Tape/ No Video Signal Indications When a function button CH 0 8 Whenever a blank section of a tape comes is pressed, e.g. PLAY, up in Play mode, or when the selected or you change channel has no broadcast signal with Weak channels, a 5-second Signal Display Feature (p. 33) set to OFF, display appears. the TV screen will turn solid blue. Current Time Function Status Channel
Summary of the content on the page No. 12
Connections Basic Connections If your TV has AUDIO and VIDEO IN terminals, connect them to DECK for higher quality picture and sound. You can enjoy stereo sound even if your TV is not stereo by connecting a stereo amplifier to DECK. a Connect DECK and TV with an RF Coaxial Cable (supplied) or an AV Cable b (not supplied) as shown in the figure below. DSS Receiver DECK TV DECK TV Cable Box DECK TV Antenna or Cable DSS Receiver IN IN Cable
Summary of the content on the page No. 13
Initial Setup (Connection) Other Connections You Can You Cannot With a Cable Box (DECK Cable Box TV) view any record (including scrambled DVD/VCR DECK ANT or CATV scrambled) TV channels. channel. IN FROM ANT. IN 1 OUT IN OUT R Cable Box use Remote VHF/ AUDIO VHF/UHF L UHF OUT TO TV IN OUT Control to select VIDEO channels without using Multi-brand control feature. Connect With Two Cable Boxes You Can You Cannot DVD/VCR DECK ANT record and view view a
Summary of the content on the page No. 14
Connections (continued) Audio Connections Ready Checklist Turn down the volume, then turn DECK, as well as other equipment to be connected, off before proceeding with connection. Do not block ventilation holes of any of the equipment and arrange them so that air can circulate freely. Read through the instructions before connecting other equipment. Ensure that you observe the color coding when connecting audio and video cables. Connecting Amplifier (2ch stereo system) Speaker DVD/VCR DECK Ampli
Summary of the content on the page No. 15
Summary of the content on the page No. 16
Initial Setup for Basic Connections (Ready to Play) Before doing Initial Setup Turn TV on. 1 a b See connections RF Coaxial Cable Connection and AV Cable Connection on page 12. 2 Set TV to channel 3. Set TV to VIDEO. [DECK ➛ ➛ ➛ ➛ ➛ TV] 3 Go to “Initial Setup (Ready to Play).” (See below.) [Cable Box ➛ ➛ ➛ ➛ ➛ DECK ➛ ➛ ➛ ➛ ➛ TV], [DSS ➛ ➛ ➛ ➛ ➛ DECK ➛ ➛ ➛ ➛ ➛ TV] Turn on Cable Box and set it to your Public Broadcasting Station (PBS) c
Summary of the content on the page No. 17
Summary of the content on the page No. 18
➡ ➡ Reset Language, Channels, Clock, VCR’s O MENU Press ACTION* PROGRAM functions are not available SET UP VCR 1 when using COMPONENT Video Output SET UP CLOCK to display MENU. SET UP CHANNEL and S-VIDEO OUT. Please set TV to IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3 either RF INPUT or VIDEO INPUT, and then press PROGRAM. SELECT : SET : SET EXIT : ACTION Language Channels Clock 2 1) Press to select 1) Press to select 1) Pres
Summary of the content on the page No. 19
Summary of the content on the page No. 20
Playback/ Record on a Tape Ready Checklist EJECT VCR/TV All connections are made. (pp. 12 ~ 15) TV and DECK are plugged in. TV is on and tuned to CH 3, 4, or VIDEO. Remote is in VCR mode. (Press VCR.) CH / Playback a Tape Insert a tape. 1 DECK power comes on. If Auto VCR/TV (see p. 32) is set to “OFF,” press VCR/TV on the remote for VCR mode. VCR Press PLAY* to play a tape. FF/ DVD 2 If tape has no rec. tab (p. 6), auto play begins. SLOW+ PLAY REW/ STOP Special Features During Play SLOW- F
