Summary of the content on the page No. 1
DVD/CD PLAYER
Hi-Fi STEREO
VIDEO CASSETTE
RECORDER
USER'S GUIDE
For model:
HR-XVC21UJ
For Customer Use:
Enter below the Model No. and Serial No. which are located on the rear of cabinet.
Retain this information for future reference.
Model No.
Serial No.
LPT0872-001A
2C50801AE Cover 1 7/10/03, 10:37
Summary of the content on the page No. 2
Dear Customer, CAUTION Thank you for purchasing the JVC DVD player video When you are not using the DVD/VCR for a long period cassette recorder. Before use, please read the safety of time, it is recommended that you disconnect the information and precautions to ensure safe use of your new power cord from the AC outlet. DVD/VCR. Dangerous voltage inside. Refer internal servicing to qualified service personnel. To prevent electric shock or CAUTIONS fire hazard, remove the power cord from the AC ou
Summary of the content on the page No. 3
When the equipment is installed in a cabinet or a shelf, MOISTURE CONDENSATION make sure that it has sufficient space on all sides to allow for Moisture in the air will condense on the DVD/VCR when you ventilation (10 cm or more on both sides, on top and at the move it from a cold place to a warm place, or under rear). extremely humid conditions—just as water droplets form on the surface of a glass filled with cold liquid. Moisture When discarding batteries, environmental problems must be conden
Summary of the content on the page No. 4
Features DVD/CD Player/Video Cassette Recorder • DVD/CD player with Video Cassette Recorder - Unique space saving design combines a DVD/CD player and a Hi-Fi Video cassette recorder. The DVD disc has much more capacity, but is the same size as the audio CD disc. Picture quality is higher than Super VHS. Audio quality is higher than audio CD. • High Quality Picture - More than 500 lines (VCR mode: 230 lines) of Horizontal Resolution. It exceeds Super VHS (400 lines) or Laser Disc (430 lines) in r
Summary of the content on the page No. 5
Contents Before using your unit Disc Playback operation Features ........................................................... 4 Disc ................................................................ 35 Contents ........................................................... 5 Setting setup language .................................. 36 Parts and functions .......................................... 6 Playback procedure ....................................... 37 Display .................................
Summary of the content on the page No. 6
Parts and functions Front STOP button VCR/DVD mode selector button Cassette Loading Slot OPEN/CLOSE button PLAY button Disc tray EJECT button Remote sensor POWER DVD indicator button CHANNEL +/– buttons REW (Rewind) button REC button AUDIO (L/R)/ VCR indicator FF (Fast Forward) button VIDEO IN jacks Rear DVD COAXIAL DIGITAL AC power cord AUDIO OUT jack RF IN jack RF OUT jack DVD S-VIDEO DVD AUDIO (L/R) OUT jack OUT jacks S-VIDEO/COMPONENT DVD OPTICAL DIGITAL DVD/VCR common AUDIO (L/R)/ Video sel
Summary of the content on the page No. 7
Display Display window 1 2 3 4 11 5 6 10 9 8 7 No. Display Description 1 VCR VCR mode 2 Playback (lights) / Auto resume (flashes) 3 Still picture 4 DVD DVD disc is inserted. 5 CD CD is inserted. 6 PM Display for afternoon (lights out in the morning) Clock display (colon [ : ] flashes) 10 : 00 01 : 00 Counter display by hour/minute at VCR/DVD / by minute/second at CD Track number display for CD 2 TV channel display for VCR CH02 7 CATV channel display C036 Error display Err L External input displa
Summary of the content on the page No. 8
Remote control Page TV/VCR/DVD switch Switch to operate TV or VCR or DVD 18,36 POWER Power on/off 18 DVD MENU Display menu of DVD software 49 MARKER Locating desired scene 47 RETURN Remove DVD set up menu 36,51 OPEN/CLOSE Open or Close the tray 37 DISPLAY Change the front Display mode 27 SUBTITLE Set Subtitle of a DVD disc 49 A.TRK Digital AUTO TRACKING 26 ANGLE Change playback angle of a DVD disc 46,49 C. RESET Reset the counter to 00:00 27 SEARCH MODE Index for DVD 39 ZERO RETURN Stop the tape
Summary of the content on the page No. 9
Remote control Inserting Batteries Open the battery compart- Install two “AA” batteries (supplied), Replace the compartment 1 23 ment cover in the direction of paying attention to the polarity cover. the arrow. diagram in the battery compartment. Battery precautions The precautions below should be followed when using batteries in this device: 1.Use only the size and type of batteries specified. 2.Be sure to follow the correct polarity when installing the batteries as indicated in the battery com
Summary of the content on the page No. 10
TV multi-brand remote control The DVD/VCR’s remote control can Preparation: control several functions on JVC • Turn the power off the TV using theTV’s remote control. remote control TVs and on the • Make sure TV/VCR/DVD switch has been slided to TV. brands of remote control TVs listed below. Press and hold VCR on the remote control until you finish the 1 step 2. Enter your TV’s brand code using the Number keys, then 2 press ENTER. • Once you have set the remote control to operate the TV, you don
Summary of the content on the page No. 11
Control four JVC VCRs The remote control is capable of Preparation: controlling four JVC VCRs Make sure TV/VCR/DVD switch has been slided to VCR/DVD. independently; one set to respond to your remote control’s A code Press and hold VCR on the remote control until you finish the 1 control signals and the other set to step 2. respond to B, C, D code control signals. The remote control is Press one of the following buttons to enter the desired code, 2 preset to send A code signals then press ENTER.
Summary of the content on the page No. 12
Basic connections If you are using an antenna system, follow these instructions. If you are a cable (CATV) subscriber,skip ahead to page 14 for the proper connections. ANTENNA TO DVD/VCR CONNECTION The DVD/VCR must be connected “between” the antenna and the TV. First, disconnect the antenna from the TV and connect it to the DVD/VCR. Then connect the DVD/VCR to the TV. Below are 3 common methods of connecting an antenna system to a DVD/VCR. Find the type of antenna system you are using and follo
Summary of the content on the page No. 13
Basic connections DVD/VCR TO TV CONNECTION After you have connected the antenna to the DVD/VCR, you must connect the DVD/VCR to the TV. Below are 3 common methods of connecting your DVD/VCR to a TV. Find the type of TV you are using and follow the connection diagram. This DVD/VCR has a single 75 ohm output for connection to a TV. If your TV has separate VHF and UHF antenna inputs (numbers 2 and 3 below), use a splitter to connect the DVD/VCR to the TV for VHF and UHF reception. TV NOTE: If a VH
Summary of the content on the page No. 14
CATV (CABLE TV) connections Many cable companies offer services permitting reception of extra channels including pay or subscription channels. This DVD/VCR has an extended tuning range and can be tuned to most cable channels without using a cable company supplied converter box, except for those channels which are intentionally scrambled. If you subscribe to a special channel which is scrambled, you must have a descrambler box for proper reception. DVD/VCR 1 TV IN (ANT) VHF/UHF Incoming Cable IN
Summary of the content on the page No. 15
CATV (CABLE TV) connections IMPORTANT: Make sure the TV/CATV menu option is set to the “CATV” mode. This DVD/VCR cannot receive scrambled programs since it does not contain a descrambler. In order to receive scrambled programs, your existing descrambler must be used. Descrambler boxes are available from cable companies. Consult your local cable company for more information concerning connection to their descrambler equipment. There are many ways to connect your DVD/VCR to a cable system. Below a
Summary of the content on the page No. 16
Playback connections The exact arrangement you use to interconnect various video and audio components to the DVD/VCR is dependent on the model and features of each component. Check the Owner's Manual provided with each component for the location of video and audio inputs and outputs. Connect to a TV with Audio/Video Output You can enjoy playback by simply connecting the unit to a TV. Connect the unit to a TV equipped with stereo audio input and video input jacks using the supplied audio/video ca
Summary of the content on the page No. 17
Playback connections Connect to a Stereo Amplifier with Audio Output You can enjoy high-quality audio by connecting the unit’s audio output to your amplifier. Connect the unit’s AUDIO OUT jacks to any line-level inputs (such as AUX, DVD, CD, etc.) of an audio amplifier. DVD/VCR Stereo Amplifier To Audio (L) Input Audio (L) Output AUDIO cable (not supplied) To Audio (R) Input Audio (R) Output Connect to an AV Amplifier with built-in digital surround If you are using an Amplifier with a built-in d
Summary of the content on the page No. 18
Setting the video channel/Setting the language Setting the Video Channel When a TV is connected with the 75 ohm coaxial cable only. To view playback of a recorded tape, Press and hold 3 or 4 on the remote for 3 seconds in standby 1 or to watch a program selected by mode. The video channel will start to flash the VCR's channel selector, the TV for 3 seconds in the display window. must be set to channel 3 or 4 (video channel). Press POWER to turn on the DVD/VCR. 2 Slide TV/VCR/DVD switch to VCR/DV
Summary of the content on the page No. 19
Tuner setting This DVD/VCR is equipped with a channel memory feature which allows channels to skip up or down to the next channel set into memory, skipping over unwanted channels. Before selecting channels, they must be programmed into the DVD/VCR’s memory. In addition to normal VHF and UHF channels, this DVD/ VCR can receive up to 113 Cable TV channels. To use this DVD/VCR with an antenna, set the TV/CATV menu option to the TV mode. When shipped from the factory, this menu option is in the CATV
Summary of the content on the page No. 20
To ADD/DELETE channels/Noise elimination Preparation: To ADD/DELETE channels • Turn ON the TV and set it to the video input mode. You can add the channels you want • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. or delete the channels you do not Then press VCR to select the VCR mode. (The VCR indicator want manually. will light.) Repeat the step 1 on page 19. CH SETUP 1 Then press or to select the TV CATV AUTO CH MEMORY “ADD/DELETE” option and press ADD/DELETE ENTER. Æ +/–/ENTER/
