Honda Automobiles 08B26-S9V-100 user manual

Summary of the content on the page No. 1

Accessory Application Publications No.
All 23607
CD CHANGER
INSTALLATION
2003-2004 PILOT
ATTACHMENT Issue Date
INSTRUCTIONS
MAY 2002
PARTS LIST
CD Changer Attachment Kit (sold separately): 8 Wire ties
P/N 08B26-S9V-100
Right base bracket
4 Washer-screws, 4 x 8 mm
2 Wire clips
Left base bracket
CD Changer (sold separately):
P/N 08A26-1B1-100
Right changer bracket
CD changer
Left changer bracket
4 Washer-screws, 4 x 6 mm
(Not used)
BUS Cable
Adhesive seal sheet
Locking covers
4 Flange bolts, 6 x 1

Summary of the content on the page No. 2

 Remove the four screws that fasten the audio TOOLS AND SUPPLIES REQUIRED brackets. Pull the audio unit out toward you, Flat-tip screwdriver unplug the vehicle connector and antenna lead Phillips screwdriver from the rear of the audio unit. Shop towel Diagonal cutters ANTENNA VEHICLE LEAD 10 mm Combination wrenches CONNECTOR AUDIO UNIT Isopropyl alcohol Utility knife INSTALLATION AUDIO Customer Information: The information in this BRACKET installation instruction is intended for use only by s

Summary of the content on the page No. 3

 Remove the center panel (four self-tapping 4. On the driver’s side of the vehicle, gently pull the screws, two clips, and unplug the vehicle center console lower cover out toward you to accessory power outlet). release the seven clips and remove the center console lower cover. Take care not to damage the clips. CLIPS (2) DRIVER’S SEAT CENTER PANEL DRIVER’S CENTER CONSOLE LOWER SELF- VEHICLE CLIPS (7) COVER TAPPING CONNECTOR SCREW 5. Remove the driver’s seat front cover by pulling it  Remove t

Summary of the content on the page No. 4

Routing the BUS cable With Navigation Unit: 6. Route the BUS cable.  Route the BUS cable from the dashboard opening to the driver’s floor. Pull out the end of Without Navigation Unit: BUS cable 30 mm from the end of the vehicle 20-pin connector, and secure the BUS cable to  Route the BUS cable from the dashboard the vehicle harness with wire ties. opening to the driver’s floor. Pull out the end of BUS cable 30 mm from the end of the vehicle  Cut the EPT seal in half. Attach 1/2 of the EPT 20-

Summary of the content on the page No. 5

7. Using 1/2 of an EPT seal attach it to the frame at 10. Install the right and left base brackets to the the location shown. Measure 450 mm from the driver’s seat raisers using two 6 x 12 mm flange end of the BUS cable to the frame, then bundle up bolts for each bracket. Do not tighten the bolts yet. the excess cable and secure it to the vehicle with three wire ties. 6 x 12 mm FLANGE BOLT EPT SEAL WIRE Cut in half. TIE FRAME RIGHT LEFT BASE BASE BRACKET BRACKET 450 mm Installing the CD Changer

Summary of the content on the page No. 6

12. Visually check the position of the spring adjusting 15. Attach one cushion tape to the rear of the CD pin on both sides of the CD changer. If the spring changer leaving half of the cushion tape extended adjusting pins are not in the horizontal (H) past the CD changer. Using scissors, cut the position, move the pins to the horizontal (H) cushion at the end of the CD changer. Fold the position by sliding them up with your fingers. ends down and around the end of the CD changer. SPRING ADJUSTIN

Summary of the content on the page No. 7

18. Plug the BUS cable connector into the CD With Cassette Player: changer connector. Bundle up any excess BUS cable and attach it to the CD changer bracket with AUDIO UNIT the two wire clips installed in step 14. BUS CABLE VEHICLE 20-PIN CONNECTOR CASSETTE PLAYER WIRE CLIP ANTENNA BUS CABLE LEAD 14-PIN CONNECTOR CD CHANGER 19. At the dashboard area, plug the BUS cable 14-pin With CD/Cassette Tuner: connector, the vehicle connectors, and the (With Navigation Unit) antenna lead into the rear of t

Summary of the content on the page No. 8

20. Slide the audio unit into the center panel opening, 21. Check that all wire harnesses are routed properly and reinstall the four screws. and all connectors are plugged in. Without Navigation Unit: 22. Reinstall all removed parts. 23. Place shipping clips in a plastic bag and put the VEHICLE bag in the glove box. BUS CABLE CONNECTOR CONNECTOR ANTENNA 24. Reconnect the negative cable to the battery. LEAD 25. Enter the customer’s radio anti-theft code, and reset the radio station presets. AUDIO