Summary of the content on the page No. 1
1x10 DVD Duplicator
User’s Manual
Model
DVW-D110H
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Safety Precautions TEAC DVD Duplicator systems are high-precision electronic devices. Do not use them in any manner other than as specified in this manual. Please read this manual in its entirety before you begin the installation procedure. Use of controls, adjustments, or performance of procedures other than those specified herein may result in hazardous radiation exposure. To prevent fire or shock, do not expose the unit to moisture or rain. To prevent electrical shock, do not attem
Summary of the content on the page No. 4
About This Manual This TEAC 1x10 DVD Duplicator User’s Manual explains how to operate the TEAC DVD Duplicator. It is divided into the following chapters: Chapter 1: Introduction This chapter describes the shipping package contents and introduces the TEAC DVD Duplicator. Chapter 2: Using the DVD Duplicator This chapter explains how to set up the DVD Duplicator. It also details its basic copy operation. Chapter 3: DVD Duplicator Functions This chapter explains all availabl
Summary of the content on the page No. 5
Table of Contents Table of Contents Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i Copyright and Trademark Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i Piracy Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 6
Table of Contents Enable Send OPC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Support UPC/ISRC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Region Free Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Partition Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 7
List of Figures Figure 1. DVD Duplicator Unit Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Figure 2. Front Panel of the DVD Duplicator Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Figure 3. LCD Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Figure 4. Rear Panel of the DVD Duplicator Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Figure 5. Test Function
Summary of the content on the page No. 8
vi TEAC 1x10 DVD Duplicator User’s Manual
Summary of the content on the page No. 9
Chapter 1. Introduction Thank you for purchasing a TEAC 1x10 DVD Duplicator. The TEAC 1x10 DVD Duplicator is a stand-alone disc-to-disc DVD Duplicator system that does not require connection to a computer. It can duplicate a single master DVD to DVD media at up to 16X speeds, resulting in an exact replica of a 4.7GB disc. It can also duplicate discs to CD-R media. The TEAC DVD Duplicator is designed to perform DVD copying quickly and accurately. The DVD Duplicator automatically identif
Summary of the content on the page No. 10
DVD Duplicator Package Contents DVD Duplicator Package Contents Your TEAC DVD Duplicator package includes the following items (see Figure 1). ❑ TEAC 1x10 DVD Duplicator unit ❑ AC power cable ❑ TEAC 1x10 DVD Duplicator User’s Manual (this manual on CD-ROM) 1x10 DVD Duplicator User’s Manual (in PDF format on CD-ROM) AC power cable Figure 1. DVD Duplicator Unit Package Contents Note: If any of the items above is missing from your package upon purchase, please contact your vendor i
Summary of the content on the page No. 11
Front Panel Front Panel Figure 2 illustrates the front panel of the DVD Duplicator unit. source drive target drives LCD control panel target drives power switch LED status indicator stabilizing feet Figure 2. Front Panel of the DVD Duplicator Unit source drive: Insert the disc to be copied into the source drive. Use the disc tray to load a DVD into the drive. You can open the tray by pressing the eject button (if the tray fails to open, you can use the emergency eject mechanism).
Summary of the content on the page No. 12
Front Panel LCD control panel: Use the control panel buttons to navigate through the various functions viewed on the LCD display. Figure 3. LCD Control Panel The DVD Duplicator control panel features an LCD display and two buttons. These buttons are described in the following table: In Operation mode, press the SET button to scroll up through the functions or menus. In Operation mode, press the RUN button to execute the selected function. target drives: Insert a blank disc
Summary of the content on the page No. 13
Rear Panel Rear Panel Figure 4 illustrates the rear panel of the DVD Duplicator unit. cooling fans AC voltage selector AC IN power connector cooling fans Figure 4. Rear Panel of the DVD Duplicator Unit cooling fans: Ball-bearing fans cool the DVD Duplicator. AC voltage selector: Use this switch to select either 115VAC or 220VAC. Caution: Before you turn on the power to the DVD Duplicator, make sure the correct voltage is selected. Otherwise, you risk damage to the unit. The def
Summary of the content on the page No. 14
Rear Panel 6 TEAC 1x10 DVD Duplicator User’s Manual
Summary of the content on the page No. 15
Setup Chapter 2. Using the DVD Duplicator This chapter explains how to set up the DVD Duplicator, as well as basic operation and menu functions. Setup 1. Select a well-ventilated area for the DVD Duplicator. Carefully remove the DVD Duplicator unit, AC power cord and user’s manual CD-ROM from the shipping box. Note: Please keep the original box and packaging materials for use in the event of future storage or transportation of the unit. 2. To ensure that the unit is properly
Summary of the content on the page No. 16
Basic Operation Basic Operation This section explains the basic operation of the DVD Duplicator. Copying from the Optical (DVD) Source Drive 1. Place a source disc in the disc tray of the source drive. 2. Switch to the Copy function by pressing the SET button. 3. Place a blank DVD±R disc into as many of the target drives as you desire, then press the RUN button to start copying. You do not need to insert a DVD disc into every available target drive. You can make fewer copies if
Summary of the content on the page No. 17
Loading Data to and Copying from the Hard Disk Source Drive Loading Data to and Copying from the Hard Disk Source Drive During initialization (see Step 4 on page 7), the DVD Duplicator performs a self- test to detect source drives. The DVD-ROM drive and hard disk drive will be detected as available source drives. The DVD-ROM drive is the default source drive. The internal hard disk drive was formatted and partitioned at the factory. Each partition occupies 9GB of hard
Summary of the content on the page No. 18
Loading Data to and Copying from the Hard Disk Source Drive 10 TEAC 1x10 DVD Duplicator User’s Manual
Summary of the content on the page No. 19
Operation Mode Functions Chapter 3. DVD Duplicator Functions The DVD Duplicator features three (3) modes of operation: ❑ Operation mode ❑ Setup mode ❑ Advanced mode Operation Mode Functions Operation mode includes seven (7) functions. Each function is explained below. Test The Test function simulates writing to the target disc. The discs will remain blank after the test is complete. This function is recommended if you are using unsupported media. This fu
Summary of the content on the page No. 20
Erase Erase The Erase function erases the data from /RW media. The default setting performs a Quick Erase when you press the RUN button. You can also press and hold the RUN button for three (3) seconds to perform a Full Erase. The Full Erase requires more time than the Quick Erase. Load The factory-installed hard disk drive was partitioned and formatted at the factory. Each partition is approximately 9GB in size. The Load function enables you to transfer data from the DVD-ROM
