Summary of the content on the page No. 1
MD-RECEIVER
KMD-673R
INSTRUCTION MANUAL
B64-1757-00 (EN)
Summary of the content on the page No. 2
Contents Safety precautions................................................3 Menu settings Menu System .............................................................................21 General features Touch Sensor Tone.....................................................................22 Power............................................................................................5 Manual Time Adjustment............................................................22 Volume.....................
Summary of the content on the page No. 3
Safety precautions IMPORTANT INFORMATION 2WARNING 2CAUTION About the disc changer to be To prevent injury and/or fire, take the To prevent damage to the machine, connected: following precautions: take the following precautions: To connect a disc changer having the "O-N" • Insert the unit all the way until it is fully • Make sure to ground the unit to a negative switch to this unit, set the "O-N" switch to locked in place. Otherwise it may fly out of 12V DC power supply. "N". place during collis
Summary of the content on the page No. 4
Safety precautions surface with a dry cloth before use. Using an Cleaning the Faceplate Terminals NOTE oil-soiled cartridge in particular may result in If the terminals on the unit or faceplate get the disc not loading or being unable to eject • If you experience problems during dirty, wipe them with a dry, soft cloth. it. (At time of cleaning, be careful not to installation, consult your Kenwood dealer. Cleaning the Unit open the shutter.) • If the unit does not seem to be working If the facepl
Summary of the content on the page No. 5
General features Power Turning on the power: Press the SRC button. NOTE Turn the power on before carrying out the following procedures. Turning off the power: Hold down the PWR OFF button for one second or more. Volume Increasing Volume: Press the u button to turn up the volume. Decreasing Volume: Press the d button to turn down the volume. ATT indicator Attenuator This function allows you to turn down the volume quickly. Turning Attenuator On/Off: Press the ATT button to switch the attenuator o
Summary of the content on the page No. 6
General features the timer function, refer to the section on the Power OFF Timer Switching Modes function under Menu settings (page 26). Switching Modes: NOTE Presetting AUX-name (Except the CA-C1AX) Each time you press the SRC button, the mode switches as In the AUX mode, press the NAME.S button for two seconds or follows: more. "NAME SET" is display and AUX-name mode is entered. Input the characters, referring to the section on "Presetting Disc Names (DNPS)" (page 20). Tuner mode MD mode Loudn
Summary of the content on the page No. 7
Please refer to the following for the adjusting values. NOTE 4 Press the AUD button to end the control mode. The System Q function changes the values of the following sound quality parameters: Bass centre frequency, bass level, bass quality factor, bass extend, middle centre frequency, middle level, middle quality "Bass" : Adjust the bass level. factor, treble centre frequency, and treble level. Setting values: - 8 – + 8 Their setting values are different depending on the setting of the speake
Summary of the content on the page No. 8
General features damaged by shocks or jolts. For that reason, keep the faceplate TEL Mute in its special storage case whilst detached. Shut down the audio system temporarily whenever an incoming call is received. NOTE The function will not work if a cable is not connected to the car phone. • Do not expose the faceplate or its storage case to direct When the telephone rings: sunlight or excessive heat or humidity. Also avoid places with When a call is received, "CALL" is displayed and all the uni
Summary of the content on the page No. 9
Tuner features Tuning 1 Press the SRC button repeatedly until the tuner mode is obtained. "TUNER" is displayed only when the tuner mode is selected. 2 Press either the FM or AM button to select the band. Each time you press the FM button, the band switches between the FM1, FM2 and FM3. Press the AM button to select the MW and LW bands. 3 • Auto Seek Tuning Press the ¢ button to seek increasing frequencies. Press the 4 button to seek decreasing frequencies. • Preset station seek tuning Press the
Summary of the content on the page No. 10
Tuner features • If the RDS station currently tuned to is transmitting no text Station Preset Memory whilst the Radio Text Display mode is turned on, "NO TEXT" will Store the frequency of the station currently being listened to. appear in the display. Whilst awaiting reception, "WAITING" will You can then recall that station with a single touch of a button. be displayed. • The £ indicator lights whilst the clock is displayed. 1 Select the band/ station that you want to have stored. 2WARNING 2 Ho
Summary of the content on the page No. 11
RDS features RDS (Radio Data System) RDS is a digital information system that lets you receive signals besides those of regular radio programmes, such as network information being transmitted from radio stations. When listening to an RDS station (ie, a station with RDS capability), the programme service name of the station is displayed along with the frequency, advising you quickly which station is being received. RDS (Radio Data System) stations also transmit frequency data for the same statio
Summary of the content on the page No. 12
RDS features 18. Children’s programmes (Children) Programme Type (PTY) Function 19. Social Affairs (Social) Conduct auto seek tuning only on those stations with selected 20. Religion (Religion) kinds of programmes. 21. Phone In (Phone In) 22. Travel (Travel) 1 Hold down the PTY button for one second or more. 23. Leisure (Leisure) "PTY" is displayed, and the Programme Type Selection (PTY) 24. Jazz Music (Jazz) Mode entered. 25. Country Music (Country) If you make no key input in 30 seconds, the m
Summary of the content on the page No. 13
Cancelling Programme Type Function During Its Operation: • Holding the TI button down for one second or more when the Press the PTY button for one second or more. TI function is on in the disc control mode results in a change to the frequency display of the traffic information station for five seconds. Traffic Information Function Presetting Volume for Traffic Information/News You can listen to traffic information. If you are listening to Preset the volume level to be used for traffic informatio
Summary of the content on the page No. 14
RDS features MD/External disc control features Radio Text Scroll This function permits the text to be scrolled and the entire text to be displayed. The scrolling method differs depending on the setting of scrolling in the menu. To scroll manually: 1 Press the CLK button to display the Radio Text. 2 Holding down the CLK button for one second or more results in one scrolling display of the text. To scroll automatically: 1 Press the CLK button to display the Radio Text. The text will be displayed i
Summary of the content on the page No. 15
Playing MDs Playing Other Disc mode This function permits the connection of optional players and Playing MDs: the playing of discs other than the loaded MD (in the current If no MDs are inserted, insert one in the slot with the label unit). facing up. If an MD is already inserted, press the SRC button repeatedly Playing Discs: until the MD mode. Press the SRC button repeatedly to select the external disc "MD" is displayed when the MD mode has been selected. control mode. The MD will start playin
Summary of the content on the page No. 16
MD/External disc control features Reversing Disc Play: Switching Display for Discs Hold down on the 4 button. Switch the display that appears whilst discs are playing. Release your finger to play the disc at the point. NOTE Switching Display for Discs: Each time you press the CLK button, the display during disc You cannot use reverse play between tracks depending on the play switches as follows. model being connected. Instead, the reverse play function is cancelled when it reaches the beginning
Summary of the content on the page No. 17
Disc Search (Function of disc changers) Track Scan Search forwards or backwards through the discs in a disc Successively play the beginning of each track on a disc until changer until you reach the one that you want to listen to. you find the track that you want to listen to. Making a Reverse Disc Search: Starting the Track Scan: Press the DISC– button to display the desired disc number. Press the SCAN button. "Scan/T-Scan ON" is displayed and the Each time the button is pressed, the displayed d
Summary of the content on the page No. 18
MD/External disc control features Random Play Magazine Random Play (Function of disc changers) Play all the tracks on the current disc in random order. Play the tracks on all the discs in the disc changer in random order. 1 Press the RDM button to switch the random play function on 1 and off. Press the M.RDM button to switch the magazine random play function on and off. "Random ON" is displayed when random play is turned on. The display of the track number changes continuously as the "M-Random O
Summary of the content on the page No. 19
NOTE When the disc or track to be played changes, the title is displayed in one scrolling display. 2 Holding down the CLK button for one second or more results in one scrolling display of the titles. NOTE • Please see the menu settings (page 26) about switching between manual scrolling and automatic scrolling. • You cannot use the text scroll function during magazine random play. — 19 —
Summary of the content on the page No. 20
MD/External disc control features NOTE Presetting Disc Names(DNPS) (Function of disc changers) You can enter up to eight characters for each name. Store the names of discs to be displayed when played. 6 Press the NAME.S button. 1 Play the disc whose name you want to preset. The disc name is stored and the disc name preset mode is NOTE cancelled. If you make no entry in a 10-second period, the name will be • This function is not available for disc changers that do not stored with the characters i
