Summary of the content on the page No. 1
INSTALL INSTRUCTIONS KK-100-03 & KK-120-03
KWIK-KIT PRISONER TRANSPORT INSERT
FORD and CHEVY VAN PRISONER TRANSPORT
TOOLS REQUIRED:
¼” & 3/8” Ratcheting Wrenches Awe or Scribe
¼” & 3/8”Air Ratchets (recommended) Pry-bar
3/8” Impact Guns (recommended) Wire Crimping tool
¼” & 3/8” Standard Socket Sets Wire Stripping tool
Powered Drill Wire Cutter
Powered Screwdriver (recommended) Circular Saw (for plywood)
Drill Bit Set Utility knife
Tape Measure Caulking gun
Screwdriver Set
Summary of the content on the page No. 2
40” COMPARTMENT (cont): QTY DESCRIPTION PART # USED FOR: 40 #10 x 1” Phillips pan head sheet metal screw GSM33196 Floor, wall to ceiling 25 #8 x 3/8” Phillips flat head screw GSM33179 Vent plates/dome lights 5 ½” Flat washer GSM31009 Grab straps/seat belts 5 ½” Lock washer GSM31030 Grab straps/seat belts 5 ½” x 1 ¼” Socket button head bolt GSM33310 Grab straps/seat belts 5 3/8” x 2” Hex head bolt GSM33032-1 Bulkheads 5 3/8” Hex nut GSM30008 Bulkheads 5 3/8” Lock washer GSM31028 Bulkhe
Summary of the content on the page No. 3
Rear OEM Trim modifications 1997-2008 Chevrolet G-Series Van Installation of Kwik Kit is very similar in Ford and Chevy Vans. All kits start with a measurement at the rear floor. The rear plastic floor trim on Chevy vans must be cut straight across as shown in photo. Measure seven inches (7 1/4”) from rear center of trim and cut straight-line full width. (Jig saw works well for this step) After plastic trim is cut an
Summary of the content on the page No. 4
Ford Driver-Side rear Ford Passenger-Side rear 8” inches 8”inches 3. PASSENGER WINDOW VAN PREPARATIONS: ***Kwik kits are designed for cargo vans with no rear OEM trim, however they can be installed into passenger window vans. Some rear trim removal or modification is required. Do not remove all rear trim and headliner as this will aid in sound deadening & insulation Note: Kwik Kits are recommended for Cargo Vans. The installer mu
Summary of the content on the page No. 5
1. Remove clear shrink- wrap covering the prisoner transport assembly. 2. This is the rear 40/60/or 80 section of the kit. 3. Remove all black hardware, wood panels and brackets holding wood panels. 4. Remove bolts holding the kit to the wood pallet. 5. With all hardware removed the remaining sections should match the sub-assemblies on the following pages 1. Remove clear shrink-wrap covering from prisoner transport assembly. rd 2. This is the 3 compartment, 40 section 3.
Summary of the content on the page No. 6
Remove all black hardware from assembled unit. This will give you the subassemblies as they are shown on the following pages. KK-XXX-03_INST_10-07 6
Summary of the content on the page No. 7
VERY IMPORTANT: Be sure that all Auxiliary lighting, video systems, Kwik kit options, and wiring are complete. Access is severely limited after kit is installed. Notch trim for wiring “B” Pillar 1 ½” Hole If optional rear load light(s) Run all wiring for dome lights, power For neatness of wiring, route all (KK-RLL) was ordered, install at vents, video system, HVAC, etc. at cables down driver-side “B” pillar. this time. this time. Tie to existing OEM harness If going under hood
Summary of the content on the page No. 8
Item #1 Item #2 Place Driver-side Bench/Wall Place Passenger-side assembly into van so bench rests Bench/Wall assembly into van so on wheel well bench rests on wheel well Item #3 Item #3 Remove steel support bracket for Remove Emergency Exit Hatch Emergency Exit Hatch pin. Re-install from Front Bulkhead to ease when attaching Front Bulkhead to installation Bench/Wall assemblies Item #3 Item #3 Item #3 Place Front Bulkhead into Attach Front Bulkhead to View of Emergency Exit
Summary of the content on the page No. 9
Item #4 & #13 Place (2) Diamond Plate Floors Be careful that exposed wires are not touching metal and optional KK- between Bench/Wall assemblies and x-VAK hoses are not completely crushed Front bulkhead. Place cardboard along side of bench while positioning Note: Vent hose will be tight in spots. If hose are crushed to an oval the floor to avoid scratching the bench. shape the airflow will still be good. Avoid completely crushing hoses. Item #5 Item #5 Item #3 Item #4 The floor(
Summary of the content on the page No. 10
Item #8 Item #8 Place Passenger-side Ceiling section into Route dome light wires, HVAC Current view of installation hoses, video cables, etc to their vehicle Do not attach any hardware at this time respective locations Item #7 & #8 Item #9 Item #7 & #8 Slide the ceiling sections out of the way in order to access A/C hoses, wires, etc. Remove Bulkhead Emergency Note: These components will be hard to access once ceiling is mounted. Exit Hatches to ease installation. Remove all slack
Summary of the content on the page No. 11
Rear Facing bench Use under seat flange holes to mark Drill floor flange and side seat and Drill through front bulkhead flange with a 5/32” drill bit. with ¼” bit. Use ¼” x ¾” bolts and serrated to attach seat to bulkhead. Attach floor flange and side seat Attach seat cover plate with # 10 x flange with # 10 x ¾” pan head sheet ½” flat head sheet metal screws. metal screws. Item #9 to #2 Loosely bolt Passenger-side rear ceilings, Bench/Wall Bolt side door and door-frame assembly t
Summary of the content on the page No. 12
Item #6 to #5 Item #6 Item #6 Place Rear Bulkhead Position between Driver and Loosely attach Doorframe to Center Doorframe into vehicle Passenger-side Bench/Wall divider using #10 x 3/8” flat head assemblies machine screws and nylock nuts Item #6 to #2 Item #11 Note: It is recommended to put rd Loosely bolt Rear Bulkhead Place the 3 Compartment edge molding on the OEM door Doorframe (at the door hinge) to Doorframe assembly. opening on the passenger side to Bench/Wall assemb
Summary of the content on the page No. 13
Item #6 Item #7, #8, #12 to #3, & #6 to #5 Continue around the entire kit bolting An awe or scribe will help Tighten screws holding Rear all Ceiling pieces to Bulkheads and align the holes Doorframe to Center Divider Doorframes using ¼ x ¾” carriage bolts, washers, and serrated nuts Pry bar Cut door gasket with utility knife. Cut gasket to the length Position the entire unit according to the of door acceptor frame. Attach as shown above. measurements on the following page. Note:
Summary of the content on the page No. 14
Top Driver-Side rear Top Passenger-Side rear Item #6 Approximately 3”inches 3” inches Item #6 Item #6 Item #7 to #1 With unit positioned according to measurements on previous page, pre- Position Driver-side Ceiling section to drill and attach a #10 x 1” sheet metal screw to hold the rear Bulkhead in mate with Bench/Wall assembly. Pre- drill 5/32” holes into Ceiling, using place while assembling the remainder of the unit. Bench/Wall assembly holes as a guide. KK-XXX-03_INST_10-0
Summary of the content on the page No. 15
Be careful when pre- drilling not to hit hoses, wires, etc… Note: Ceiling is behind wall Item #8 to #2 Item #5 & #4 to van floor Pre-drill ceiling with 5/32” drill bit and attach #10 x Be Sure Floor Is Square To Benches & Bulkheads. 1” Phillips pan head sheet metal screws to hold Attach Divider to vehicle. Pre-drill through floor(s) Ceiling to Bench/Wall assembly. Repeat these steps using 3/16” drill bit and attach using ¼” x 1 ½” hex on the Passenger-side Ceiling section head lag bo
Summary of the content on the page No. 16
On the Rear doorframe, remove the sheet metal screws installed earlier. Drill 3/8” holes through the doorframe, floor, and vehicle. Attach using 3/8” x 2” hex head bolts, washers, fender washers, lock washers, and hex nuts. Item #6 to van floor Item #11 to van floor 3/8” x 2” Hex head bolt, washers, and nut Item #11 to van floor rd On 3 Compartment Doorframe repeat the same steps done on Rear Doorframe. Only one bolt is used and must be located just to the left of the doors hinge
Summary of the content on the page No. 17
Socket Pin Item #14 to doors and frames Attach Ball & Socket Style Doorstop. st 1 Attach “Pin” portion of assembly. Attach to threaded hole on the door using a ¼” x 1” Hex head bolt. nd 2 Attach the “Socket” and bracket portion. Attach to doorframe using #8 x ¾” Phillips machine screws and keps nuts. Item #11 Item #15 In the upper corner of each side Place trim panels as shown above rd of the 3 Compartment Pre-drill through trim panel (only) Doorframe are small filler with
Summary of the content on the page No. 18
FINAL INSTALLATION PHOTOS Forward Compartment for models KK-100-03, KK-100-04, KK-120-03 and KK-120-04 Optional Storage Compartment (Sold Separately) KK-XXX-03_INST_10-07 18
Summary of the content on the page No. 19
PRISONER TRANSPORT OPTIONS – (All SOLD SEPERATLEY) KR-CCL-1 KR-DL KK-PVENT KK-RLL PT-VIDEO-X C-VS-1800-ECO w/ C-TCB-7 & C-3090-7 KK-XXX-03_INST_10-07 19
Summary of the content on the page No. 20
Item 3 Item 7 Item 12 Item 1 Item 8 ITEM DESCRIPTION 1 Driver-side Bench/Wall 2 Passenger-side Bench/Wall 3 Front Bulkhead Item 11 4 Diamond-plate Floor Item 10 5 Divider 6 Rear Bulkhead/ Doorframe Item 14 Item 14 7 Driver-side Rear Ceiling Item 9 8 Passenger-side Rear Ceiling 9 Separator Bulkhead Item 13 10 Front Compartment “L” Bench 11 Front Compartment Doorframe 12 Front Compartment Ceiling 13 Front Compartment Floor Item 4 14 (2) Door
