Summary of the content on the page No. 1
INSTRUCTION MANUAL
1½ H.P. Single-Stage
Dust Collector
(Model 50-850)
PART NO. 902115 - 11-15-02
Copyright © 2002 Delta Machinery
To learn more about DELTA MACHINERY
ESPAÑOL: PÁGINA 15
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call 1-800-223-7278 (In Canada call 1-800-463-3582).
Summary of the content on the page No. 2
GENERAL SAFETY RULES Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may result. Safety equipment such as guards, push sticks, hold-downs, featherboards, goggles, dust
Summary of the content on the page No. 3
ADDITIONAL SAFETY RULES FOR DUST COLLECTORS WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY. 1. DONOTOPERATE THIS MACHINE until it is 14. DO NOT use the dust collector as a toy. DO NOT assembled and installed according to the instructions. use near or around children. 2. OBTAIN ADVICE FROM YOUR SUPERVISOR, 15. DO NOT insert fingers or foreign objects into the instructor, or another qualified person if you are not dust intake port or discharge port. Keep hair, loose f
Summary of the content on the page No. 4
UNPACKING AND CLEANING Carefully unpack the tool and all loose items from the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household floor paste wax. ILLUSTRATIONS ARE REPRESENTATIVE ONLY AND MAY NOT DEPICT THE ACTUAL COLOR, LABELING OR ACCESSORIES AND MAY BE
Summary of the content on the page No. 5
ASSEMBLY WARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTION MANUAL. ASSEMBLING B A CASTERS TO BASE 1. Insert threaded rod of caster (A) Fig. 4, into the hole located on the underside of base (B) and fasten with 3/8" lockwasher (C) and 3/8-16 hex nut (D). Fig. 5, illustrates the caster fastened to the base. C 2. Assemble the remaining three casters to the underside of the base in
Summary of the content on the page No. 6
4. Assemble the remaining drum supports (F) Fig. 9, to F base (A) as shown. F A 5. Assemble “U” bracket (H) Fig. 10, to drum (J). Place Fig. 9 a 5/16" flat washer then a 5/16" lockwasher onto a 5/16- 18x5/8" hex head screw. Insert the hex head screw (K) thru the hole in the “U” bracket and the hole in the drum, thread a 5/16" hex nut onto the hex head screw and J tighten securely. Repeat this process for the remaining hole. NOTE: “U” bracket should be mounted to the right H side of opening (L)
Summary of the content on the page No. 7
9. Attach the lower dust bag retaining clip (A) Fig. 14A, to the dust collector drum. Align the two holes (B) in the retaining clip (A) Fig. 14A, with the two holes in the drum. Insert a 1/4-20x5/8" hex head screw through the holes in B the retaining clip and the holes in the drum. Place a 1/4" flat washer onto the screws, and thread 1/4-20 hex nut s on the screws and tighten securely. Repeat this process A for the three remaining sides of the drum. Fig. 14A B A ASSEMBLING DUST INTAKE PORT AND C
Summary of the content on the page No. 8
ASSEMBLING FILTER AND A DUST COLLECTION BAGS B TO DRUM 1. Hook the loop on the top of filter bag (A) Fig. 18, onto filter bag support rod (B) as shown. 2. Assemble extension rod (C) Fig. 19, onto the end of filter bag support rod (B). Raise support rods (B) and (C), Fig. 18 with filter bag (A) attached and place end of support rod (C) into holes of bracket (D). NOTE: Flared end of filter bag extension rod will prevent the rod from sliding through bracket. B A D 3. Position open end of filter bag
Summary of the content on the page No. 9
ASSEMBLING DUST INTAKE C E D HOSES TO BLOWER AND MOTOR ASSEMBLY KEEP DUST CAPS INSTALLED AT ALL TIMES OVER INTAKE PORTS. REMOVE A DUST CAP ONLY WHEN A FLEXIBLE HOSE IS ATTACHED TO THE INTAKE PORT. The dust collector is supplied with a 4" dia. flexible dust intake hose. A B 1. To assemble the intake hose (A) Fig. 23, to the blower assembly, pull the dust cap (B) from the dust intake port Fig. 23 (C) and slide the dust cap collar (D) farther onto the dust purchase the hose and install as in STEPS
Summary of the content on the page No. 10
240 VOLT, GROUNDED OUTLET BOX SINGLE PHASE OPERATION The motor supplied with your tool is a dual voltage 120/240 CURRENT CARRYING volt motor. If it is desired to operate your dust collector at PRONGS 240 volts, single phase, contact your local Authorized Delta Service Center or qualified electrician for proper procedures to rewire your dust collector motor for 240 volt operation and wiring a 240 volt attachment plug to the power supply cord. The tool with a 240 volt plug should only be connected
Summary of the content on the page No. 11
OPERATING CONTROLS WARNING:BEFOREOPERATINGTHEMACHINE, FOROPERATORSAFETY, ALWAYSMAKECERTAINTHAT EACHDUSTINTAKEPORT(WHICHISNOTBEING USEDORPREVIOUSLYASSEMBLEDTOADUSTCOLLECTION SYSTEM) BECOVEREDWITHADUSTINTAKEPORTCAP. THEROTATINGFANINSIDETHEBLOWERHOUSINGIS ACCESSIBLETHROUGHTHEDUSTINTAKEPORTSANDIS HAZARDOUS. ALWAYSWEARPROPERAPPAREL, DO NOTWEARJEWELRY, ANDKEEPFINGERSANDALLFOREIGN OBJECTSOUT OFTHEDUST INTAKEPORTS. FOLLOW THE SAFETY RULES STATED EARLIER ON PAGES 3 AND 4 IN THIS MANUAL. D A A B C Fig. 28
Summary of the content on the page No. 12
ACCESSORIES A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our Web Site www.deltamachinery.com for a catalog or for the name of your nearest supplier. WARNING: Since accessories, other than those offered by Delta, have not been tested with this product, use of such accessories could be hazardous. For safest operation, only Delta recommended accessories should be used with
Summary of the content on the page No. 13
PORTER-CABLE • DELTA SERVICE CENTERS (CENTROS DE SERVICIO DE PORTER-CABLE • DELTA) Parts and Repair Service for Porter-Cable • Delta Machinery are Available at These Locations (Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable • Delta) ARIZONA ILLINOIS MINNESOTA Cleveland 44125 Minneapolis 55429 Tempe 85282 (Phoenix) Addison 60101 (Chicago) 8001 Sweet Valley Drive 5522 Lakeland Avenue North 2400 West Southern Avenue 400 South Rohlwing Rd. Unit #
