Summary of the content on the page No. 1
Save This Manual For
Future Reference
\
Dust CoBlection
System
Serial
Number
Model and serial number may be
found on the motor cover.
You should record both model and
serial number in a safe place for
future use.
DUST COLLECTION
S YS TEM
FOR YOUR
SAFETY:
° assembmy
READ ALL
INSTRUCTIONS
ooperation
CAREFULLY.
"parts
orepamr
Sold by SEARS, ROEBUCK AND CO., Chicago, IL. 60684 U.S.A.
Part No. SP5373 Printed in Taiwar_
Summary of the content on the page No. 2
• • •:• •_:-•-::_:/.'- • ••• ,.,. ,,i _. FULL:ONEYEAR WARRANTY ON CRAFTSMAN DUST C-OLL_ If within 0ne year from the date of purchase, thls Craftsman Dust Collection System falls due to a defect in maierlal0r workmanship; Sears wil! repair it,free of charge; WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTINGTHE NEAREST SEARS SERVICE CENTER/ DEPARTMENTTHROUGHOUT THE UNITED STATES. This warranty applies only while this product is used in the UnitedStates. Thiswarranty givesyou specific legalrights,
Summary of the content on the page No. 3
_ CAUTION: if usingthts Dust Collection System BEFORE EACH USE: to help keep airborne wood dust in heavy usage within acceptable limits, you must regularly monitor 1. inspect your Dust Collection System. if any parts air borne dust andmaintain Dust Collection System are missing, bent, or faiJin any way, or any electri- to avoid exceeding dust limits. Each application is cal components do not work properly, turn off the unique. Your maintenance schedule must, there- Dust Collection System, remove
Summary of the content on the page No. 4
:4 AFETY INSTRUCTIONS :FOR: POWER TOOLS 1. KNOWYOUR TOOL 12. USESAFETY GOGGLES (Head Protection) Read and undersiarid owner's manual and labels : ::wear safety goggles (mUstcomply with ANSI Z87.1 ) 3tt_xed to the tOOl [:.earn its appiicalion and limita- at all times., Everyday eyeglasses only have impact nuns as welt as its(specffic potenl.iat hazards pec, resistant lenses; they are NOT safety glasses. Also. uafiar tolhis tOoL use lace or dust mask if cutting operation is dusty, 2, _ GROUND THE
Summary of the content on the page No. 5
........ iiiiii ii ,i ,i, introduction The Craftsman Dust Collection System is specifically quency of slatic shocks in your home, the best remedy designed to capture sawdust and wood chips at the is to add moisture to the air with a console or installed source. The fine dust is filtered by the upper bag while humidifier. heavy particles settle in the lower bag for easy removal. Do not use as a vacuum. The safety information in this manual is highlighted by the following safety alert symbol. _ CA
Summary of the content on the page No. 6
Tools Needed I_NPAC_KiR_ i_::_ _HECKING CARTON €ONTENTSI! Adjustable Wrench Screwdriver ...... i CARTON CONTENTS LISTf Key Descrlptlon Qty, A _; FiltedDust Bag ........................................... 1 B Fitter/Dust Bag Hanger ........................... 1 C Handle. ...................................................... 1 D Filtration Housing ....................................... 1 E _ inlet Guard ................................................. t F : ::Right Side Support Leg ............
Summary of the content on the page No. 7
assembmy MOUNTING FRONT PRVOTING CASTERS 1, Locate the following items from the loose parts bag: Description Qty. A A Pivoting Casters ................................... 2 B Hex Nuts* (3/8 - 16) .............................. 2 C Flat Washers* (3/8 x 3/4) ...................... 4 D Acorn Nuts*, ......................................... 2 E E Base Plate ............................................ 1 0* * }terns are shown actual size 2. Screw a hex nut completely on the Caster bolt. ACORN NUT_, 3
Summary of the content on the page No. 8
:: 4i Support the opposite side of Filtration Housingw_th a b[()ck of wood_ A;:Ptace:O÷Ring in relief of Inlet pipe (See page!8) 5.: Position Inlet Guardin tine withthe threaded holes On the base of the Filtration Housing. NOTE: Makesureinlet Guard is pointing to rear of machine_ 6. Place Iockwasher and flat washer on hex screw and insert through the holes of the Inlet Guard into the threaded holes of the Filtration Housing as shown. 7. Complete the process for the other three holes using same m
Summary of the content on the page No. 9
IIIILui_ LIIIiiiiiiiiiiiiijljl iiii, iii ii i ii ii MOUNTING INLET BRACKET 1, Locate the following items from the loose parts bag: Description Qty. c D A R A Flat Washers* (5/16x 11/16xl/!6) ..... 2 B Hex Screws* (M8 x 1.25 - 12)............... 2 * Items are shown actual size C Flat Washers *(1/4 x 1/2) ...................... 2 D Hex Screws* (M6 x 1 - 12) ................... 2 2, Insert Inlet Bracket between relief flange of Inlet Guard and against inside edge of angle flange on Support Leg. Mak
Summary of the content on the page No. 10
A AG HOLDER * Items are shown actual size i i 1_LoCate the foUowing items from the loose parts bag: Description Qty. FILTER/ .....A Hex Nut* (M6 X 1) ................................ 1 DUST BAG B Lockwasher* (1/4) ........................... ..:: 1 HOLDER C Flat Washer* (1/4x 1/2) ....................... 1 2_Attach hexnut to threaded portion of Filter/Dust Bag HEX N UT_._ Holderand place lockwasher and flat washer on nut LOCKWASH ER _e= as shown. FLAT WASHER "-'''_ /" 3, Insert Filter/Dust Bag H
Summary of the content on the page No. 11
SAWDUST CHUTE F_LTRATION HOUSING EXTENSION CHiP BAG ASSEMBLY - LOWER FiLTRATiON HOUSING 1. Insert lower Chip Bag by tilting the Metal Reinforced Bandat an angle and positionit through the hole inthe lower Filtration Housing. 2. Tuck one side of the Band under the Sawdust Chute Extension. 3. Allow the opposite side to rest on the ridge of the opening. 4. Tug on the Chip Bag to insure proper seating, UPPER FILTER/DUST BAG ASSEMBLY 1. Disconnect the Adjustable Band Clampand insertthe FILTER/ FILTER
Summary of the content on the page No. 12
ii:i;ii!ii!iiii!iiiiii i i!i !ii I'H iiii: : / i ThliS_Dust!i¢olie_ion System i!s designed to be corn elecffiCai parts, do not operate this Dust Collection netted directly t0:thewoodwOrking machines. Pieasel System in!areas with flammable vapors such as useoniythel_artS provided for maximum effJctency: ilghterl fluld, cleaners, oil-base paints, gasoline, 4!!IDiameterx :_4)" Hose_ PVC Vulcanized rubbe_ alcohol or explosive dust such as coal, magnesium, with wire reinforcement and 2- 4'_clamps_
Summary of the content on the page No. 13
', rlqplll i ....... ................. ............... jl ,l! i ON ! OFF SWITCH On the rear of the Motor Housing above the Handle, is the Switch Box. The ON!OFF Switch has the ability to be turned "ON" when the Red Key is properly installed. Switch to the "ON" position by moving the switch upward. Turn the switch "OFF" by moving downward. Remove the Key from the switch whenev- er the saw is turned "OFF" and keep it out of the reach of children. _ WARNING: THE DUST COLLECTION SYSTEM CAN START ACC
Summary of the content on the page No. 14
...................... '.......... .............. " " ".... " 4 _1 , , _ __ This appliance is for use on a nominal 120-volt circuit, and has a grounded plug that looks likethe plug illustrat- ted below. Atemporary adapter may be used to connect this plug to a 2-pole receptacle, as shown below, if a properly grounded outlet is not available. The temporary TION: CONNECT TO _ A::120Vi 15"AMP, BRANCH adapter should be used only until a properly grounded CIRCUIT AND USEA15=AMP,TIME DELAY FUSE OR outl
Summary of the content on the page No. 15
i l i i i ,inl _ WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF" AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE MAINTAINING YOUR DUST COLLECTION SYSTEM ...... _ WARNING: TO AVOID INJURY FROM ELEC- .___I-- j_ TRIC SHOCK OR SUDDENLY STARTING UNIT, AL- /_ WAYS REMOVE SWITCH KEY AND KEEP UN- .-_.. i " PLUGGED WHILE UNIT IS DISASSEMBLED tN ANY _i_;-_:_-_i _\ WAY. ALWAYS REASSEMBLE WITH RECOM- \_' MENDED PARTS BEFORE PLUGGING UNIT IN, _" CHIP COLLECTING BAG REMOVAL 1. Push Bandup and sfide opposite e
Summary of the content on the page No. 16
MOTOR : _CAUTION: To avoid eye Injury or adverse Excessive dustfin _tO_: couldcause excessive heat: in motor. : reaction to dust, high air pressure should not be used especially In poorly ventilated areas. Every effortshou!d be imade _to: prevent foreign material The operator performing this cleaning function should fromenteting the motor:i When operated ur_ler condi- tions likely to permit accumtllations of dust, dirt;or waste wear safety goggles and filter mask within the motor, a visual inspe
Summary of the content on the page No. 17
PROBLEM PROBABLE CAUSE REMEDY SUGGESTED Excessive noise. 1. Motor 1. Have motorchecked by qualified service technician. Repair service is avaiable at your nearest Sears store. " , ............. l .... " " ' Motor fails to devet- 1. Circuit overloaded with 1. Do not use other appliances or motors on same circuit op full power. when using the Dust Collection System. NOTE: LOW VOL- lights, appliances and other motors. 2. Increase the wire sizes on extension cords, or reduce TAGE: (Power out- 2. Und
Summary of the content on the page No. 18
........ i i parts PARTS!LIsT, FOR!; :CRAFTSMAN DUST COLLECTION SYSTEM f MODEL 113.299780 ,'_" E 45 i i i 18
Summary of the content on the page No. 19
m repaintparts PARTS LiST FOR CRAFTSMAN DUST COLLECTnON SYSTEM MODEL 113.299780 Always order by Part Number - not by Key Number. Item Part Part Item NO, No. D esCraptIon No. No. De _rlptton Wash#r, Flat 5/16 x ! 1/16 1 819166 27 819198 o_ Hot Filler/Dust Bag 2 819172 × 3/32 Mo 1 H P 3 819187 Sw :ch 28 819196 Leg 4 819302 29 819207 Caster, Fixed ,_ Ke_ Switch Base 5 819189 30 819199 Col with Plug 6 819191 Cas*,er, Pivoting Ha_ 31 819203 7 STD833025 32 STD541037 * Nut, Hex 3/8 - 16 * Sc_ ,Hex Hd M
Summary of the content on the page No. 20
ii, i,,, _'_ p,- DUST COLLECTmON SYSTEM SERVICE Service is available by returning this unit to the nearest Sears Service Center/Department through- out the United States. MODEL NO. Model and serial numbers may be found on the Motor Cover of your Dust Collection System. 113.299780 Dust Collection System HOW TO ORDER WHEN ORDERING REPAIR PARTS, ALWAYS REPAIR PARTS GIVE THE FOLLOWING INFORMATION: PART DESCRIPTION PART NUMBER NAME OF ITEM MODEL NUMBER 113.299780 Dust Collection System All parts list
