Summary of the content on the page No. 1
USER’S MANUAL
Part 2
1
Tapeless Digital Answering
System Telephone with
Time/Day 1817
Fold open this manual for information
about this telephone’s installation
and operation. Please also
read Part 1 — Important
Product Information.
AT&T and the globe symbol are registered trademarks of AT&T Corp. licensed to Advanced American Telephones.
© 2000 Advanced American Telephones. All rights reserved.
Printed in Mexico. 850002684 Issue 1AT&T 6/00
Summary of the content on the page No. 2
INSTALLATION Modular Standard Telephone Electrical Jack Outlet Telephone Power Line Cord Cord Strain Relief Tab 4 Connect the line cord to a Set Dial Mode modular wall jack. This telephone comes set for touch tone Plug the free end of the line cord into dialing. Use the Dial Mode switch on the a modular wall jack. Make sure it bottom of the phone to select TT (touch snaps firmly into place. tone) or DP (dial pulse), depending on your service. When set to Dial Pulse mode, the 5 Connect the hand
Summary of the content on the page No. 3
INSTALLATION Figure 1 Figure 2 Figure 3 Figure 4 5 Connect the line cord to the modu- Wall Installation lar jack and mount the phone onto the 1 Remove the base. wall jack. Slide the base sideways as shown by Plug the free end of the line cord into the REMOVE arrow (Figure 1). a modular wall jack. Make sure the 2 Connect the short line cord to the cord snaps firmly into place. Place telephone. the phone on the wall jack mounting Plug the five inch line cord into the studs and pull down until i
Summary of the content on the page No. 4
TELEPHONE OPERATION Redial Ringer Volume This telephone always stores in memory Slide the RINGER switch on the front of the last number manually dialed (up to 24 the telephone (near the dial pad) up to digits). The number remains in memory increase volume, or down to decrease until you dial another number. volume. The lowest setting turns the ringer off. To dial the last number called from this phone, lift the handset and press R. Receiver (Handset) Volume Use the handset VOLUME switch on the Fl
Summary of the content on the page No. 5
IN CASE OF DIFFICULTY If you have difficulty operating this Messages Are Incomplete telephone answering system, try the • The system can accept messages up to suggestions below. For Customer Service, three minutes long. If a caller leaves a visit our website at www.telephones.att.com very long message, part of it might be or call 1 800 222–3111. Please retain lost when the system disconnects the your receipt as your proof of purchase. call after three minutes. • If the caller pauses for more tha
Summary of the content on the page No. 6
IN CASE OF DIFFICULTY Power Failure Recovery Message Window Displays If the system is disconnected from AC Clock needs to be reset. power, the answering system will not operate, but you will still be able to make Flashing – System is busy or in use and receive calls. Your announcement and — OR — messages are retained in memory during a Steady – System in Remote Access power failure, but you will need to reset mode. the clock when power is restored. See the instructions on the bottom of the unit.
Summary of the content on the page No. 7
ANSWERING SYSTEM OPERATION Displays number of messages and other information Set/review day and time Flashing: new messages/ Steady: saved messages Set/review feature set up Adjust message volume Delete all or Turn answering some messages system on or off Record/review outgoing announcement OR Record a memo skip all or part of OR repeat all or announcement part of message Play messages OR Stop message playback Access custom- calling services Redial last Store and access number called numbers
Summary of the content on the page No. 8
ANSWERING SYSTEM OPERATION Turning the System On/Off Call Screening/Intercept Use O to turn the system on or off. Set the system to answer calls, and set the When the system is off, the Message volume control so you can hear the caller’s Window is blank. message. If you choose not to hear the caller’s message, adjust the volume to the Volume Control lowest setting. The Message Window Use VOLUME buttons (+ and -) to displays 0. adjust the volume of the system’s speaker. If you decide to take the
Summary of the content on the page No. 9
ANSWERING SYSTEM OPERATION Remote Access Code Listening to Your Messages You can use many features of this As the system plays back messages, the answering system remotely from a touch Message Window displays the number of tone phone. Most features can be the message playing. Before playing each accessed only after you enter a Remote message, the system announces the day Access Code, which is preset to 123. You and time the message was received. After can review the Remote Access Code by playing
Summary of the content on the page No. 10
ANSWERING SYSTEM OPERATION Deleting Messages Recording a Memo You can record a memo to be stored as an Delete All messages incoming message. The memo can be up Hold down D. The system announces to three minutes long, and will be played “Messages deleted” and permanently back with other messages. deletes messages. The Message Window displays 0. If you haven’t listened to all of 1 Press and hold . After the the messages, the system beeps five times, beep, speak toward the microphone. and does not
Summary of the content on the page No. 11
ANSWERING SYSTEM OPERATION FROM A REMOTE TOUCH TONE PHONE Connect with the Deleting Messages Delete All Messages Answering System After you have listened to all messages and 1 Dial your telephone number from a heard the two beeps, press 33. touch tone phone with a different telephone number. Delete Selected Messages 2 When the system answers, enter your Press and release 3 while the message three-digit Access Code during or after you want to delete is playing. the announcement. The system announ
Summary of the content on the page No. 12
ANSWERING SYSTEM OPERATION FROM A REMOTE TOUCH TONE PHONE Changing Remote Access Code Turn System On When the system is off, it answers after 10 1 Press 99. The system announces rings, announces “The machine is off,” and “Enter new code.” beeps twice. 2 Enter your new Remote Access Code 1 Press 0 to turn the system on. (any number between 100 and 999). 2 The system beeps twice and is ready 3 If a valid code is entered, the system to answer calls and record messages. announces the new Remote Acce
Summary of the content on the page No. 13
© 2000 Advanced American Telephones.. All rights reserved. © 2000 Advanced American Telephones.. All rights reserved. Printed in Mexico. 850002692 6/00 Printed in Mexico. 850002692 6/00 PERF. fold fold 1 1 Tapeless Digital Answering System 1817 Tapeless Digital Answering System 1817 Remote Commands Remote Commands To connect with your answering system: To connect with your answering system: 1 Dial your telephone number from a touch tone phone. 1 Dial your telephone number from a touch tone pho
Summary of the content on the page No. 14
ONE KEY REMOTE COMMANDS ONE KEY REMOTE COMMANDS Play All Play New Delete Play All Play New Delete Repeat Stop/Exit Skip Repeat Stop/Exit Skip System Record System Record On Memo On Memo TWO KEY REMOTE COMMANDS TWO KEY REMOTE COMMANDS Turn system off 00 Turn system off 00 Delete all messages 33 Delete all messages 33 Review announcements 71 Review announcements 71 Record announcement 7*, speak after beep, press 5 Record announcement 7*, speak after beep, press 5 to stop to stop Room monitor 98, p
