Summary of the content on the page No. 1
Viking Installation Guide
Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information,
call 1-888-VIKING1 (845-4641)
or visit the Viking Web site at
vikingrange.com
Professional & Designer 200/325E/450E Series
Built-In Dishwashers
F20760 EN (091510)
Summary of the content on the page No. 2
Table of Contents IMPORTANT–Please Read and Follow! • Before beginning–please read these • Please ensure that this product is properly instructions completely and carefully. grounded. • Do not remove permanently affixed labels, • The installer should leave these Warnings & Important Information ______________________________________ 3 warnings, or rating plates from the instructions with the consumer who should Dimensions & Cutout Dimensions ______________________________________ 6 dishwasher. T
Summary of the content on the page No. 3
IMPORTANT–Please Read and Follow! IMPORTANT–Please Read and Follow! A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state/local WARNING laws, or local ordinances. • The required use of a GFI is normally related to the location of a receptacle with respect to any significant sources of water or moisture. • Viking Range Corporation will NOT warranty any problems resulting from GFI outlets which are not installed properly or do not meet the requirements below. If the us
Summary of the content on the page No. 4
33-7/8” (86.0 cm) 34” min. (86.4 cm) 35” max. (89.0 cm) 24” (61.0 cm) 23-7/8” (60.6 cm) Dimensions & Cutout Dimensions Specifications Professional Series 26-3/8” 26-3/8” Built-In Dishwasher (67.0 cm) (67.0 cm) 23-3/4” 23-1/8” (60.3 cm) (59.0 cm) Description 200/325E/450E Models Overall width 23-7/8” (60.6 cm) Overall height from floor 33-7/8” (86.0 cm) min. to 35” (89.0 cm) max. 2-5/8” 3-3/16” (6.7 cm) Overall depth from rear–Professional (8.1 cm) To edge of side - 24” (61.0 cm) - includes door
Summary of the content on the page No. 5
Custom Door Panel (Installation Option) a (Specifications for FDB200/DFB450E Models) Have the overlay panel constructed per dimensions. The panel thickness MAY NOT exceed 5/8” (1.6 cm) for flush installation in most cabinets. Ensure that the design, construction, 11-17/32" and installation of the panel overlay and its (29.3 cm) handle mounting is sufficient to reliably operate 5/8" (1.6 cm) 5/8" in this application with a maximum panel weight 5/8" (1.6 cm) (1.6 cm) of 18 lbs. (8.2 kg.) Custom pa
Summary of the content on the page No. 6
General Information General Information • Read these instructions carefully and • For service convenience, a shut-off valve in Item (2) should, if the partition is Electrical Connections completely before installing the dishwasher. (not supplied) should be installed in the wood, be smooth and rounded or, if Grounding Instructions The installation should be carried out by a supply line in a readily accessible location the partition is metal, be covered with This appliance must be grounded. In the
Summary of the content on the page No. 7
Hardwire Conduit Option a b Trim Installation Options (not available on all units) To install dishwasher without trim, remove the 6 screws (3 per side) and remove trim. To attach wiper gasket to dishwasher, pull protective film off adhesive back on wiper gaskets and apply to leading edge of dishwasher frame. Trim gasket to fit. 1a 1 Remove any loose items in the dishwasher and carefully lay Remove bottom pan and front plate. the dishwasher on its back. NOTE: Be careful not to pinch hoses or powe
Summary of the content on the page No. 8
Trim Installation Options (cont’d.) (not available on all units) Trim Installation Options (cont’d.) (not available on all units) Dishwasher will ship with trim installed for panel flush install. If needed, To install dishwasher cabinet flush with trim, remove the 6 screws (3 per side) attach wiper gasket by pulling protective film off adhesive back on wiper holding side trim on. Shift the side trim forward. Use rear hole on side trim and gasket and apply behind hemmed edge of side trim. the
Summary of the content on the page No. 9
Installation Procedure Counter Balance Spring Adjustment - If Necessary a b 1 1b Increase tension Decrease tension 1 Disconnect cable from hook. Set counter balance spring connector in appropriate location. Carefully lay dishwasher on its back and attach the kick To adjust the depth of the kick plate, loosen screws on plate brackets. Screws for the brackets will already be the bracket and position in the required depth. Tighten screws and repeat for other side. in the base. NOTE: Be caref
Summary of the content on the page No. 10
Installation Procedure (cont’d.) Installation Procedure (cont’d.) 5b Front Panel Attached 7 7b Front Panel Removed Attach screws through trim pieces into cabinets. Attach screws through bracket into cabinets (select models). (select models). Remove front panel to access the front leveling legs. 9 8 1.0” 5c 6 (2.5 cm) Minimum 20” (50.8 cm) Cut here for 5/8” from floor (1.6 cm) Cut here for 3/4” (1.9 cm) Identify discharge connection size; cut line to Install High Loop Cli
Summary of the content on the page No. 11
Installation Procedure (cont’d.) Air Gap Air Gap 11A 11B Performance Checklist Testing for Leaks Unit Reset • If the unit should need to be reset for any A qualified installer should carry out the reason, push and hold the “START” button following checks: for 4 seconds. h Remove packaging and parts. h Turn on the water supply and check for leaks. (Discharge with air gap) (Discharge with food waste disposer and air gap) h Turn the power on at breaker/fuse box and test the dishwasher operatio
Summary of the content on the page No. 12
Service & Registration Only authorized replacement parts may be used in performing service on the appliance. Do not repair or replace any part of the appliance unless specifically recommended in the manual. All servicing should be referred to a qualified technician. Contact Viking Range Corporation, 1-888-VIKING1 (845-4641), for the nearest service parts distributor in your area or write to: VIKING RANGE CORPORATION PREFERRED SERVICE 1803 Hwy 82W Greenwood, Mississippi 38930 USA The serial numbe
