Summary of the content on the page No. 1
This manual MUST be attached to the wall in close proximity to the door.
®
®
5150, 5155, 5200 & 5255
LIMITED WARRANTY
The Manufacturer warrants that its door and its hardware fittings will be free from defect in workmanship and material. Should any defects in workmanship or material appear
within ONE YEAR of delivery, manufacture shall, upon notification, correct such nonconformity at its option, by repairing or replacing any defective part or parts. See maintenance
and painti
Summary of the content on the page No. 2
OPERATING ZONE You Can Save Time And Effort If You First Establish All The Facts About 1/4-20 Nut (2) The Operating Zone Inside Step Plate The Operating Zone is the area surrounding the door opening, extending upward and backward as far as the door will travel. We call it Step Dish the Operating Zone because it is the area that the door will have to operate within and the dimensions are critical and must be known in Cut Out advance of a door and operator installation. TRACK DEPTH DIM. A DI
Summary of the content on the page No. 3
EXTEND JAMBS TO OPENING HEIGHT plus STEP 13: Operator Trolley Bracket Installation: Attach the operator trolley bracket as illustrated in Fig. AA. This trolley DIM Y plus 1 1/2 (MINIMUM LENGTH) bracket is limited to doors 142 X 10 (5 Sections high and smaller). For doors 142 X over 10 (5 sections) and 143 thru 202 by all heights see Fig. BB. For doors over 202 by all heights see Fig. CC. (3) 1/4-20 X 7/8 SELF MINIMUM DRILLING TEK SCREWS HEADROOM U-BAR DIM Y REQUIRED HEADER TO MODEL
Summary of the content on the page No. 4
Intermediate hangers for all NOTE: Use a chalk line or line level to ensure doors over 11 high and over all bearing brackets are in line. (± 1/8) 14 wide. Positioned half way 1/4 GRADUATION between jamb and rear 8 SECTIONS HIGH OR LESS hanger. FIG. F Lateral brace all hanger angles. #5 HINGE (2in. Track) #7 HINGE (3in. Track) #4 HINGE (2in. Track) #6 HINGE (3in. Track) #3 HINGE (2in. Track) #5 HINGE (3in. Track) 3/8 dia. Bolt should Single Wide 2 #2 HINGE (2in. Track) protrude into track
Summary of the content on the page No. 5
STEP 4. MODEL 5150 & 5200 U-bars & struts to be secured to the section using (2) 1/4 - 20 x 7/8 TEK screws at each end. SPRING TURN CHART Additional 1/4 - 20 x 7/8 TEK screws will need to be used at each hinge location. U-bars and struts are to be mounted at the top of section under hinges and across top brackets, as seen in Fig. K. Refer to STRUTTING SCHEDULE for strut placement. DOOR HEIGHT 400-8 400-12 5250-18 800-32 DOOR HEIGHT 400-8 400-12 5250-18 800-32 NOTE: Strut clips used at top b
Summary of the content on the page No. 6
Spring mounting pad. 2 X 6 White Steel STEP 6. Secure the end hinges, (one side only) center hinges, and strutting ( if applicable) as previously illustrated. Locate the Pre-Cast Pine or denser. Secured with min. Lock Section (usually the second section) and insert a roller into the end hinge. Stack this section into the opening by hooking the (4) 5/16 x 4 lag bolts into header. roller in the vertical track and lowering it onto the bottom section. Insert a roller into the appropriate end hin
Summary of the content on the page No. 7
spacing is achieved. Doors over 11 ft. high and over 14ft. wide must have (1) intermediate drop hanger as shown in Fig. S on Page 13. Doors between 16 and 18 high must have (2) intermediate drop hangers as shown in Fig. S on Page 13. 24 MINIMUM SPRING PAD WIDTH TWO SPRINGS Doors over 18 high must have intermediate drop hangers placed on 6 centers. 20 (6) 13 STEP 13: Release the locking pliers from vertical track and check the doors counterbalance. RIGHT HAND DRUM SPLIT SOLID Adjust sp
Summary of the content on the page No. 8
This illustration shows TWO SPRINGS 15 radius track (3) 3/8 x 3/4 truss bolts and nuts. W/TEK Screw to Steel (2) for securing end bracket (3-3/4) (1) for securing horizontal angle This illustration shows TUBULAR OR 1 PIECE 12 radius track 3-1/2 W/Lag Bolt to Wood. RIGHT HAND DRUM SOLID SHAFT This illustration shows BLACK 15 radius track W/Concrete Anchor Extra 3/8 truss bolt and nut WINDING CONE WINDING CONE BLACK BLACK RED Intermediate hangers for all doors over 11 high and over 14 wi
