Summary of the content on the page No. 1
DS-50/DS-75/DS-100 MINI ROLL-UP DOORS
INSTALLATION INSTRUCTIONS
IMPORTANT NOTICE !!
Read the enclosed instructions carefully before attempting to install this door. Pay close
attention to all warnings and important safety notices.
This manual MUST be attached to the wall in close proximity of the door.
©Copyright 2004 Wayne-Dalton
P/N 300847, DOC #101-0117 REV 03
Summary of the content on the page No. 2
IMPORTANT SAFETY NOTICES Read the enclosed instructions carefully before attempting installation. If there are any questions about any of the procedures, do not perform the work. Instead, have a trained door technician do the installation or repairs. 1. Operate the door ONLY when it is properly adjusted and free of all obstructions. 2. The door is constantly under EXTREME SPRING TENSION. Repairs, adjustments, installation and removal, ESPECIALLY of SPRINGS AND RELATED PARTS, are dangerou
Summary of the content on the page No. 3
INTRODUCTION This manual's main function is to assist the installer in correctly installing the doors to ensure safe operation. Compliance with building codes, enforced in your area, is required. All Wayne-Dalton DS-50, DS-75, and DS-100 Mini Roll-Up Doors follow these general instructions. Additional installation information for the specific door shipped is found with the packing slip and on supplementary drawings. There are also bolt and small sealed parts bags with accessory lists, d
Summary of the content on the page No. 4
STEP 1 UNPACKING DOORS Before removing the door from any packaging, inspect the packaging for visible signs of damage. If damage is noted, file a freight claim with the freight company immediately. Remove the door from the packaging. Do not cut tape that holds door in a roll. You will be told in STEP IMPORTANT! #7 when to cut the tape. No guarantee will be given by Wayne-Dalton if the door is not installed as instructed. Please review all instructions thoroughly before starting in
Summary of the content on the page No. 5
STEP 3 INSTALLING GUIDES Position the left hand guide 3/8” from the edge of the left hand jamb and loosely clamp in place. Using a level, adjust the guide so that it is plumb and tighten the clamp. Measure the exact curtain width of the door and add 7/8” to obtain the inside of guide to inside of guide measurement. Use this measurement to locate the right hand guide. Loosely clamp the right hand guide to the jamb. Plumb the guide and tighten the clamp. Using a string and leve
Summary of the content on the page No. 6
STEP 5 LIFTING THE CURTAIN ASSEMBLY Curtain assembly is heavy. Allowing curtain assembly to fall WARNING while lifting, could result in severe or fatal injury. To avoid severe or fatal injury, never walk, stand, or work WARNING below curtain assembly before it is secured to support brackets. The left hand end of the curtain assembly (when installed) will be the end with the spring. Lift the curtain assembly up to the brackets and insert the left hand axle end into the large
Summary of the content on the page No. 7
STEP 7 PRE-TENSIONING THE DOOR SPRING Spring tension can cause curtain assembly to rotate rapidly, possibly resulting in severe or fatal injury. To prevent such WARNING injury, securely hold curtain assembly to prevent rotating. Starting with the bottom bar at the top of the curtain roll, apply two complete turns of pre-tension to the spring by rotating the curtain roll in the direction shown. The amount of tension required may vary slightly. Final adjustment, if necessary, will
Summary of the content on the page No. 8
STEP 9 CHECKING AND ADJUSTING SPRING BALANCE Spring tension can cause curtain assembly to rotate rapidly, possibly resulting in severe or fatal injury. To prevent such WARNING injury, securely hold curtain assembly to prevent rotating. Move the door up and down to check for proper spring tension. If the door lowers easily and raises hard, more spring tension is required. If the door lowers hard and raises easily, less spring tension is required. If a tension adjustment is necess
Summary of the content on the page No. 9
II: DS-50 & 100 ‘C’ Stop-Clip Attachment: For doors with an aluminum bottom bar, a ‘C’ (4) ¼ - 20 carriage bolts stop-clip will need to be installed. Only one bolt is required to secure the stop-clip to the bottom bar when attaching a lift handle on that side. Repeat assembly procedure for both sides. (4) ¼ - 20 flange nuts (2) ‘C’ stop-clips (4) ¼ - 20 carriage bolts III: ‘C’ Stop-Clip w/ Inside Slide Bolt Attachment: (4) ¼ - 20 flange nuts *pre-attached to btm b
Summary of the content on the page No. 10
STEP 12 INSTALLING THE OPTIONAL TENSION-PRO SPRING ADJUSTMENT BRACKET STEP #12a: Install the Tension-Pro™ bracket on the left hand side of the curtain assembly per STEP #4 & #5 in this manual. Insert cotter pin through hole in the axle end. Do not use large washer (shown in step #5) on the Tension-Pro™ bracket side axle end. Bend the ends of the cotter pin to secure in position. STEP #12b: Stretch and attach spring end to the spring holder plate of th
Summary of the content on the page No. 11
To Increase Spring Tension: Move the door to the fully open position and place clamps on the guides to prevent door from closing. Using a large pipe wrench, grip the tensioning hex plate and rotate the ratchet gear assembly in the direction indicated above until an audible “CLICK” is heard (one gear tooth). Operate the door to determine if the spring tension increase was sufficient. Repeat spring tension increase procedure until door is properly balan
Summary of the content on the page No. 12
Roll-Up Sheet Door LIMITED WARRANTY Wayne-Dalton P.O. Box 67- Mt. Hope, Ohio 44660 The Manufacturer warrants the ROLL-UP SHEET DOOR and hardware fittings for a period of ONE YEAR from the time of delivery against any defects in workmanship or material. Manufacturer shall, upon notification, correct such nonconformity at its option, by repairing or replacing any defective part or parts.
Summary of the content on the page No. 13
Limited Warranty for Paint on the following Wayne-Dalton products Roll-Up Doors Model Nos. • DS 50, • DS 75, • DS 100, • DS 200, • DS 350 Wayne-Dalton Door & Systems Div. 2589 County Road 168 Interior Systems Dundee, OH 44624 • Filler Panels –corrugated and flush • Roll-Up Frames • Hallway Soffit 1-800-795-5095 • Cor-O-Doors – corrugated and flush • Cor-O-Wall • Entry Soffit • Swing Doors – corrugated and flush • Mod-U-Wall • Burglar Bars • All angle and channel associa
Summary of the content on the page No. 14
This limited warranty applies to the effects of weathering and does not apply to other causes of degradation, such as in the case of (by way of example and without limitation): (1) Painted surfaces on Product which has been subject to scratching or abrasion or impact (including without limitation “paint rub” occurring in metal to metal contact and movement); has been abused, altered, modified, used in a manner not originally intended, or stored in a manner contrary to instructions of M
Summary of the content on the page No. 15
F. Other Terms. This limited warranty is made to the Original Owner, exclusively, and not to anyone who or which subsequently owns or possesses the structure where the Product has been installed. This limited warranty is not assignable or otherwise transferable. It will not pass to another person that acquires ownership of the structure on or in which the Product is installed; and this limited warranty does not apply to any failure or defect occurring after the structure in or on which
