Stanton PROFESSIONAL DJ MIXER M.201 user manual

Summary of the content on the page No. 1

Summary of the content on the page No. 2

IMPORTANT SAFETY INSTRUCTIONS 1. Read these Instructions 11. Only use attachments/accessories specified by the 2. Keep these Instructions manufacturer. 3. Heed all Warnings 12. 4. Follow all Instructions Use only with the cart, stand, tripod, 5. Do not use this apparatus near water bracket, or table specified by the 6. Clean only with dry cloth manufacturer, or sold with the apparatus. 7. Do not block any ventilation openings. Install in When a cart is used, use caution when accord

Summary of the content on the page No. 3

MIXER CONTENTS 1. Input fader - Controls individual source levels (channels) in the mix. 2. Input toggle switch - Selects which source will be active based on what you have connected to the rear panel input section (phono/line). 3. Channel EQ - Adjusts the high, mid and low frequency levels of the input channels for good sound. 4. Channel Gain – Adjusts the pre-fader volume for cleaner sound. 5. Replaceable Crossfader - Achieves clean segues between the two input chan

Summary of the content on the page No. 4

MIXER CONTENTS 14. Grounding post - for turntable connection. Always use this connection when using standard turntables with ground cable. (Some turntables like the T.80 / T.120 do not require grounding wire). 15. Phono Inputs – Plug your turntables in here. When these connectors are used, your signal is fed directly to the high-quality RIAA phono pre-amplifiers. Use this position only for turntables. Line level sources will overload the sensitive phono pre-amps and

Summary of the content on the page No. 5

QUICK SETUP DIAGRAM Study this setup diagram. Make sure all faders are at "zero" and all devices are off. First, connect all input sources and processors. Next, connect your microphone and monitor headphones. Finally, connect the stereo outputs to the power amplifier(s) and/or audio receivers such as tape decks. Plug your mixer into AC power. Now you are ready to switch everything on. IMPORTANT: Always switch on your audio input sources such as turntables or CD players first, then your m

Summary of the content on the page No. 6

SPECIFICATIONS INPUT / OUTPUT IMPEDANCE & SENSITIVITY: LINE -14dB/10K OHM ±2dB PHONO -50dB /47K OHM ±2dB MIC -60dB /2.2K OHM ±2dB MASTER 1K OHM PHONES 0dB/33 OHM ±2dB (LOAD=32 OHM) MAX. OUTPUT (THD=1%) MASTER MORE THAN +14dBV PHONES MORE THAN +21dBV CHANNEL BALANCE WITHIN 3dB FREQUENCY RESPONSE: LINE 20-20KHz ±2dB PHONO 20-20KHz +2, -3dB (RIAA) MIC 20-20KHz +2/-3dB OUTPUT NOISE (IEC-A WEIGHTED) LINE LESS THAN -90dBV PHONO LESS THAN -80dBV MIC LESS THAN -50dBV

Summary of the content on the page No. 7

Stanton Magnetics, Inc. – Warranty Provision – Returns for Repairs or Replacement WARRANTY Through Stanton’s authorized dealers around the World, Stanton, or one of Stanton’s authorized distributors outside the U.S., will, without charge, repair or replace, at the sole discretion of the entity responsible for making the repair or providing the replacement, any Stanton merchandise proved defective in material or workmanship for a period of one (1) year following the date of original purcha

Summary of the content on the page No. 8

cut along dotted line STANTON WARRANTY REGISTRATION CARD If you have internet access, please register your product at www.stantondj.com. Otherwise, return this card completely filled out in order to validate your warranty. PERSONAL INFO Name Address City State Zip Country Telephone PRODUCT INFO Model Number Serial Number Date of Purchase Where did you buy this product?

Summary of the content on the page No. 9

PLACE STAMP HERE Stanton Magnetics, Inc. 3000 SW 42nd Street Hollywood, FL 33312 U.S.A.