Summary of the content on the page No. 1
Start Here
16 USB
Important: Do not connect the USB cable until Step 16 or software may not
1
install properly.
Follow the steps in order. If you have problems during setup, see Troubleshooting in the last section.
2
Remove cardboard and tape
Make sure to remove all tape and cardboard on the inside
of the device.
3
Locate components
1 6
1 Windows CD 1 Windows CD
2 Macintosh CD 2 Macintosh CD
3 3 User Guide
2 7 4 4 power cord and adapter
HP Photosmart 2600/2700 series all-in-one H
Summary of the content on the page No. 2
4 Verify that the control panel faceplate is attached Attach the control panel faceplate (if not attached) a b b c a a Align the control panel faceplate with the device. b b Moving from left to right, press down each of the 1 1 2 3 areas shown in graphic b until you securely attach the faceplate. c Make sure that all buttons are visible and that the edges of the faceplate are even with the device. HP All-in-One The control panel faceplate must be attached for the HP A
Summary of the content on the page No. 3
5 Attach trays and load paper ab c de a a Insert the tabs of the bottom tray into the device, and then lower until the tray is fl at. b b Slide the paper adjuster over to the left. c c Insert plain white paper. d d Attach the top (output) tray. Make sure you hook the top of the edge tray into the light gray latches, and then lower. e e Flip the paper tray extender. HP All-in-One • 3
Summary of the content on the page No. 4
6 Connect the power cord and adapter 16 USB Important: Do NOT connect the USB cable until Step 16 or software may not install properly. 7 Connect the supplied phone cord (1-LINE) Connect one end of the supplied phone cord to the phone port on the left (1-LI NE) and the other to a wall jack. To connect an answering machine or use your own phone cord, see the User Guide. 4 • HP All-in-One
Summary of the content on the page No. 5
8 Press the On button and configure On a b OK OK a After you press the On button, the green light fl ashes, and then becomes solid. b Wait for the language prompt before continuing. Use the arrow keys to select your language, press OK , and then confi rm. Use the arrow keys to select your country/region, press OK , and then confi rm. 9 Open the access door Lower the access door. The print carriage moves to the right side. If you have a carriage jam, see T roublesho
Summary of the content on the page No. 6
11 Insert the tri-color print cartridge a a b b The device must be On before you can insert the print cartridges. a Slide the tr i-color print cartridge into the left slot as shown. b Push the top part of the cartridge fi rmly up and into the slot until it snaps into place. 12 Insert the black print cartridge a a b c a Slide the black print cartridge into the right slot. b b Push the top part of the cartridge fi rmly up and into the slot
Summary of the content on the page No. 7
13 Align the print cartridges a a OK b c b d OK c A fter you insert the cartridges, a message appears that the device is ready for alignment. a Press OK to print the alignment page. b The alignment page prints. (This may take a few minutes.) c Lift the lid. Place the top of the alignment page face down in the left front corner of the scanner glass. Close the lid. d Press the OK button again to begin alignment. After the On light stops blinking, a mes
Summary of the content on the page No. 8
CD 15 Insert the correct CD Windows Macintosh a HP All-in-One W indows CD a HP All-in-One Macintosh CD b b c Macintosh Users: a Insert the gray HP All-in-One M acintosh CD. b Continue to the next page. Windows Users: a Insert the green HP All-in-One W indows CD. b Follow the onscreen instructions to install the software. c On the Connection Type screen, make sure to select directly to this computer . Continue to the next page. CD Note : If the startup
Summary of the content on the page No. 9
USB 16 Connect the USB cable Macintosh a USB HP All-in-One USB Macintosh Users: a Connect the USB cable to the port on the back of the HP All-in-One, and then to any USB port on your computer. Windows a USB USB HP All-in-One USB Windows Users: a Follow the onscreen instructions until you see the prompt to connect the USB cable. (This may take several minutes.) Once the prompt appears, connect the USB cable to the port on the back of the HP All-in-One, and
Summary of the content on the page No. 10
USB 16 Connect the USB cable (continued) b “HP All-in -One Installer” c If you do not see this screen, see Troubleshooting in Setup Assistant the last section. Windows b Double-click the HP All-in -One Installer icon. c c Make sure you complete all screens, including the Setup Assistant. After you complete software installation, you are fi nished. Windows Users: c Follow the onscreen instructions. Complete the Fax Setup Wizard and the Sign up now s
Summary of the content on the page No. 11
Windows USB HP All-in-One Windows CD 15 Windows Microsoft USB HP All-in-One W indows CD 15 16 Windows USB USB 4 16 www.hp.com/support 50% 10% © Copyright 2005 Hewlett-Packard Development Company, L.P. Printed in []. Printed in [].
Summary of the content on the page No. 12
*Q5610-90149* Troubleshooting *Q5610-90149* Q5610-90149 Pr oblem : The Carriage jam message appears on the display. Ac tion : Turn the device off. Check the tray area for cardboard and tape. Make sure the print carriage can move freely. Press the ON button after you have removed all packing materials. Problem : The R emove and check print cartridges message appears after you insert print cartridges. Action : Remove print cartridges. Make sure you remove all tape from the copper contac
