Summary of the content on the page No. 1
Summary of the content on the page No. 2
Notice To prevent fire or shock hazard, do not expose the unit to rain or WARNING moisture. The symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit. The symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock t
Summary of the content on the page No. 3
Caution This installation should be made by a qualified service person and should conform to all local and national electrical and mechanical codes.
Summary of the content on the page No. 4
PRECAUTIONS 1. Do not attempt to disassemble the camera. In order to prevent electric shock, do not remove screws or cover. There are no user-serviceable parts inside. 2. Do not expose the camera to rain or moisture, or try to operate it in wet areas. Take immediate action if the camera becomes wet. Turn the power off and refer servicing to qualified service personnel. Moisture can damage the camera and also create a danger of electric shock. 3. Do not use strong or abrasive detergent
Summary of the content on the page No. 5
Hi-Res. B/W camera instruction manual ADC 660N and ADC 660P _________________________________ Copyright ©2007 Sensormatic Electronics Corporation. Product specifications subject to change without notice. Certain product names mentioned herein may be trade names and/or registered trademarks of other companies. Customer Service Thank you for using American Dynamics products. We support our products through an extensive worldwide network of dealers. The dealer through whom you originall
Summary of the content on the page No. 6
Hi-Res. B/W camera instruction manual ADC 660N and ADC 660P _________________________________ I. CONNECTORS AND CONTROLS..................................................................................7 1. VIDEO OUTPUT CONNECTOR (BNC)................................................................................ 7 2. POWER INPUT CONNECTOR (SCREW TERMINAL) ............................................................... 7 3. AUTO IRIS LENS CONNECTOR FOR VIDEO DRIVE LENS..................
Summary of the content on the page No. 7
Hi-Res. B/W camera instruction manual ADC 660N and ADC 660P _________________________________ I. CONNECTORS AND CONTROLS 1. Video Output Connector (BNC) 1.0V p-p/75 Ω composite video signal is provided at this connector. 2. Power Input Connector (screw terminal) 7
Summary of the content on the page No. 8
Hi-Res. B/W camera instruction manual ADC 660N and ADC 660P _________________________________ This terminal accepts 12 VDC or 24 VAC. Power Requirement: Maximum 200 mA (12 VDC), Maximum 100 mA (24 VAC). Recommended Power Supply: Minimum 500 mA (12 VDC); Minimum 300 mA (24 VAC). Caution: Use a 24V AC / 12V DC class 2 LPS supply only. 3. Auto Iris Lens Connector for VIDEO Drive Lens This connector supplies 9 VDC power and video signal, without sync, for video-drive type Auto
Summary of the content on the page No. 9
Hi-Res. B/W camera instruction manual ADC 660N and ADC 660P _________________________________ When using a DC drive lens, the ALC/ELC DIP #1 must be set to the ALC (OFF) position. 5. BLC (Backlight Compensation) ON/OFF Switch If the subject you wish to view is too dim because of a bright background, set the BLC DIP switch #2 to ON to compensate for the bright background. With BLC on, the background brightness may saturate in some cases. This function may not operate properly if th
Summary of the content on the page No. 10
Hi-Res. B/W camera instruction manual ADC 660N and ADC 660P _________________________________ 6. ALC/ELC Select Switch (EE/ELC is ON; ALC/AI is OFF) This switch is used to select EE (electronic exposure)/ELC (electronic light control) mode or AI (Auto Iris lens)/ALC (automatic light control) mode. DIP switch 1 is set to ON for EE/ELC and OFF for AI/ALC. In the EE/ELC mode, a continuously variable electronic shutter is employed to automatically control the exposure time of the CCD image s
Summary of the content on the page No. 11
Hi-Res. B/W camera instruction manual ADC 660N and ADC 660P _________________________________ 7. AGC ON/OFF Switch This switch is provided for the AGC circuit. The AGC circuit incorporated into the camera boosts the sensitivity automatically when the scene illumination is insufficient. 8. INT/LL Switch (LL is ON; INT is OFF) This camera can operate independently, using its internal crystal-controlled sync generator, or it may be synchronized using line-locking. To select one or the
Summary of the content on the page No. 12
Hi-Res. B/W camera instruction manual ADC 660N and ADC 660P _________________________________ 1. While observing the video output signals from both cameras on an oscilloscope, turn camera A's V-phase control (on back of camera) until vertical sync from both cameras is in phase. 2. If camera A's adjustment range is insufficient, adjust camera B's V- phase control in the opposite direction to camera A until they are in phase. 3. If these adjustments do not bring vertical sync from both cam
Summary of the content on the page No. 13
Hi-Res. B/W camera instruction manual ADC 660N and ADC 660P _________________________________ 11. ALC Level Adjustment Potentiometer for DC Drive Lens This potentiometer is used only if the camera is fitted with a DC drive Auto Iris lens. It is used to control the amount of light striking the CCD image sensor. Turn off AGC. With a brightly lit scene adjust LENS-IRIS control for a clean 1 VPP video level with no blooming. Turn AGC back on after adjustment is complete. LENS-IRIS le
Summary of the content on the page No. 14
Hi-Res. B/W camera instruction manual ADC 660N and ADC 660P _________________________________ Monitor Screen LEVEL Control Direction To increase the brightness Clockwise To decrease the brightness Counterclockwise 12. Power Indicator LED This LED turns ON only when power is supplied properly and the DC-DC converter (or the regulator) inside the camera works properly. 13. Backfocus Adjustment Screw This screw is used to position the CCD image sensor at the precise point of focus o
Summary of the content on the page No. 15
Hi-Res. B/W camera instruction manual ADC 660N and ADC 660P _________________________________ 15
Summary of the content on the page No. 16
Hi-Res. B/W camera instruction manual ADC 660N and ADC 660P _________________________________ 14. C Mount Adaptor Ring The C-mount adaptor ring is used only if a C-mount lens is used on the camera. If a CS- mount lens is used, the adaptor is not necessary. To install the adaptor, first screw it into the lens mount opening on the camera. Then screw the C-mount lens into the adaptor. 15. CCD Dust Protective Cap Remove this cap before installing the lens. Do not handle or leave the cam
Summary of the content on the page No. 17
Hi-Res. B/W camera instruction manual ADC 660N and ADC 660P _________________________________ II. EXAMPLES OF CONNECTIONS 1. Simplest: One monitor system with one camera 2. One monitor system with two or more cameras 17
Summary of the content on the page No. 18
Hi-Res. B/W camera instruction manual ADC 660N and ADC 660P _________________________________ III. DIMENSIONS 18
Summary of the content on the page No. 19
Hi-Res. B/W camera instruction manual ADC 660N and ADC 660P _________________________________ IV. SPECIFICATIONS MODEL ADC660N ADC660P TV SYSTEM EIA CCIR EFFECTIVE PIXELS 768(H) X 494(V) 752(H) X 582(V) IMAGE DEVICE 1/3” INTERLINE TRANSFER CCD SCANNING SYSTEM 2:1 INTERLACE SYNCHRONIZING SYSTEM INTERNAL/LINE LOCK SELECTABLE HORIZONTAL RESOLUTION 580 TV LINE VIDEO OUTPUT LEVEL 1 V pp/75 ohm S/N RATIO MORE THAN 50 dB (AGC OFF) MIN.ILLUMINATION (F1.2) 0.03 lux ELECTRONIC IRIS 1/60
