Summary of the content on the page No. 1
B/W CCD Camera
CS3950D
Specification
Contents
1. Product Description ·································································································1
2. Features ·························································································································1
3. Configuration················································································································2
4. Option Unit·················
Summary of the content on the page No. 2
BEFORE USE - GENERAL SAFETY INSTRUCTIONS This instruction manual contains important information for the operator (user) and/or people around him/her to avoid personal injuries, or property damages against him/her or people around him/her by using this product correctly. • Prior to use, read this operation manual carefully to fully understand its instructions for correct use. • After reading, keep this manual by the side of your equipment for your future reference. WARNINGS & CAUTIONS
Summary of the content on the page No. 3
●Handling Precautions DANGER If any overheating sign is observed, discontinue the use immediately. In the event that smoke, smell, or any other overheating sign is observed, turn its power switch OFF immediately, and remove your plug from outlet. Do NOT try to continue to use this device. To do so in spite of clear signs of malfunction invites a Unplug fire, an electric shock hazard, or a serious damage. In such case, contact us or our dealer /distributor from which you purchased t
Summary of the content on the page No. 4
DANGER Do NOT place any potentially-hazardous things on this device. Do NOT place any things on the device which may, if it gets into the inside of the body, damage the inner parts of the device (such as a flower pot, glass, cosmetics, a container filled with liquids or chemicals, as well as small metal parts, etc.). If Avoid tumbled, the liquids inside the bottle, etc. may get into the chassis, causing a fire or an electric shock accident. Do NOT damage the power cord. Do NOT
Summary of the content on the page No. 5
This device complies with Part15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. RESTRICTION FOR USE Avoid irregular signal interface. Do not attempt irregular signal interface other than specified. Under signal interface other than recommended/specified in this instruction manual, the devic
Summary of the content on the page No. 6
OTHER INSTRUCTIONS Do NOT use power other than specified Be sure to use DC12V power supply. The camera is designed to work only under the specified voltage. Do NOT attempt to drive the camera with the power other than DC12V. Operating the camera under power other than DC12V invites a fire or an electric shock hazard. Avoid intensive light Do NOT expose the camera’s image-pickup-plane to sunlight or other intense light directly. If the part of CCD is exposed to spot-intensive
Summary of the content on the page No. 7
1. PRODUCT DESCRIPTION Model CS3950D is an integrated type B/W CCD camera with a XGA format all-pixel-data readout CCD. The model is suited for high-speed, high-resolution image processing use. Its compact, light-weight body is ideal for system integration. 2. FEATURES (1) All pixel's data readout With its built-in all-pixel-data-readout CCD, this model can read out image-data just in approximately 1/30 sec. A frame-shutter reads out all data even under RTS (Random Trigger Sh
Summary of the content on the page No. 8
4. OPTION UNIT (1) DC SYNC IN cable ············Model name : CPRC3700 [2m,3m,5m,10m] (2) Camera adapter ···················Model name : CA170 (3) Camera-mounting kit············Model name : CPT *Contact your dealer / distributor for details of option units. *Conformity of an option part and EMC conditions About the conformity of EMC standard of this machine, it has guaranteed in the conditions combined with the above-mentioned option part. When used combined parts other than speci
Summary of the content on the page No. 9
(a)Non-reset mode (Under internal sync / external sync --- Consecutive VD IN) Exposure starts at the timing of TRIG signal IN. After each exposure is completed, the camera outputs video at each next VD IN timing. Automatically returns to normal shutter if fixed H level (after approx. 1/6s) TRIG IN not acceptable for 1V after mode chenge TRIG IN (Positive) INT/EXT VD CCD Exposure Exposure time (E-shutter speed or pulse width) VIDEO OUT Definite Outputs VD,V-SYNC Outputs video at the next
Summary of the content on the page No. 10
Automatically returns to normal shutter if fixed H level (after approx. 1/6s) TRIG IN not acceptable for 1V after mode chenge TRIG IN (Positive) CCD Exposure Exposure time (E-shutter speed or pulse width) VIDEO OUT Definite VD,V-SYNC pause during standby VD,V-SYNC output for 1V only WEN OUT (Standard) Normal shutter Random trigger shutter Normal shutter Exposure time delay under RTS When the RTS is active, both in FIX mode and PULSE W mode, there is a time delay of approximately 1.4
Summary of the content on the page No. 11
(5) Partial-scan mode selection (Camera rear-panel DIP SW) Switches partial-scan mode Note: Sometimes phenomenon called as “whiteout” occurs at the top of the screen when there is strong incident light entering in the wide area of a CCD, however, this is not a malfunction. If this occurs, reduce the amount of incoming rays. (5-1)1/2 Partial-scan --- Screen center 1/2 readout Only the center portion of 344H out of the total effective lines 768H (excluding BLK time) is read out. Av
Summary of the content on the page No. 12
(5-2)1/4 Partial-scan --- Screen center 1/4 readout Only the center portion of 137H out of the total effective lines 768H (excluding BLK time) is read out. Available both under external / internal mode. Normal- 137H High-speed speed 316H transfer transfer Normal- 137H speed transfer High-speed 315H transfer ■Under normal shutter (Electronic shutter OFF) Notes: * Under ext. sync, the ext. VD should be 1V = 193H. ** Under normal shutter, set the rear-panel DIP SW #5, #
Summary of the content on the page No. 13
6. SPECIFICATIONS [Basic spec] (1) Image sensor All Pixel’s Data Read-out Interline CCD Total pixels 1077(H) x 788(V) Active pixel 1034(H) x 779(V) Video output pixels 1024(H) x 768(V) Scanning area 4.81(H) x 3.62(V) mm (=Equivalent to 1/3 type CCD size) Unit cell size 4.65(H) x 4.65(V) micro m (Square-grid array) (2) TV system Special format (Non-conforming to EIA) (3) Scanning lines 796 lines (4) Interlace Non-interlace mode (5) Sync system Internal/External automatic switc
Summary of the content on the page No. 14
[Shutter trigger spec] Exposure-starting-cue signal in random trigger shutter mode (1) Input level LOW level: From 0 through 0.5V HIGH level: From 4 through 5V (2) Input impedance High impedance (10k-ohm) (3) Capture timing Rising edge detection (Positive) / Falling edge detection (Negative) (Switching via rear-panel DIP SW) (Initial factory setting: Rising edge) (4) Pulse width Minimum 2 micro s Maximum 1/8s [Sync signal spec] (1) Readout signal WEN readout timing pulse (2) Pola
Summary of the content on the page No. 15
(3)Restart / Reset Restart / reset available via ext. VD signal (Switching via rear panel DIP SW, Initial OFF) Notes : * The exposure-time (shutter-speed) is determined by ext. VD interval. ** Enabled when rear-panel DIP SW OFF. ***Provide Consecutive HD. [Partial scan] (1)Operation mode No Scan mode Sync Reset E-shutter Normal E-shutter RTS 1 Non-reset Enabled [Option] Enabled Internal 2 V-reset Disabled 1/2 partial 3 Consecutive HD VD IN Non-reset Enabled [Option] Enabled
Summary of the content on the page No. 16
[Mechanical spec] (1) External dimension 44 x 29 x 78(D) mm (Not including protrusion) Refer to the attached external view drawing (2) Weight Approximately 130g (3) Lens mount C mount (4) GND / insulation Circuit GND - Chassis electrically conducted * * * * C C C Co o o om m m mb b b bi i i in n n na a a at t t ti i i io o o on n n n o o o of f f f C C C C- - - -m m m mo o o ou u u un n n nt t t t l l l le e e en n n ns s s s As for the C-mount lens used combining t
Summary of the content on the page No. 17
[Connector pin assignment] (1) Compatible connector HR10A-10P-12S (Supplied by HIROSE ELEC.) (2) Pin assignment Pin Signal No. (Standard) Connector pin layout 1 DC12V GND 2 DC12V ① ⑨ 3 VIDEO GND ② ⑧ 4 VIDEO OUT ⑩ 5 HD GND ⑪ ⑫ ⑦ ③ 6 HD IN 7 VD IN ④ ⑥ ⑤ 8 TRIG GND 9 NC 12 pin male Picture Rear-panel camera connector 10 WEN OUT (Rear-view) 11 TRIG IN 12 VD GND Notes : *Before connecting / disconnecting the connector, make sure the camera power is OFF. **For board connection
Summary of the content on the page No. 18
[Switch setting] (1) CCU rear-panel DIP SW No. Function OFF ON 1 E-shutter-speed 2 See shutter-speed table (Table 1) 1 O 3 (SHUT) 4 2 5 Shutter mode N S S S S H H H H U U U U T T T T See shutter-mode table (Table 3) 6 (SMODE) 3 Partial scan 7 See partial-scan table (Table 2) 8 (PART) 4 Positive Negative 9 TRIG polarity 5 (Rising edge) (Falling edge) S S M M O O D D E E S S M M O O D D E E Notes: *Initial factory setting: All OFF 6 **Set No.9 OFF when TRIG IN OPEN. 7 P P A A
Summary of the content on the page No. 19
[Relative Spectrum Response] *Including lens characteristics, Excluding light source characteristics [Optical black characteristics] 2 Effective 779 788 Image Area V 7 1034 40 3 1077 H Total pixels : 1077(H) x 788(V) Effective pixels : 1034(H) x 779(V) Optical black Horizontal : 3pixels --- 40pixels Vertical : 7pixels --- 2pixels D4133738B 13
Summary of the content on the page No. 20
7 7 7 7.... T T T TI I I IM M M MI I I IN N N NG G G G C C C CH H H HA A A AR R R RT T T T (1)H rate timing D4133738B 14 EXT HD 1CLK=33.9ns ± ± ± ±0.5μ μμ μ s s s s INT HD 102CLK (3.46μ μμ μ s s s s) 5CLK 5CLK 40CLK 164CLK 29CLK 3CLK 1024CLK 5CLK 1 1 1 1 1 1 0 0 0 0 0 0 2 3 3 2 3 3 O 9 0 4 1 5 6 9 0 4 O B D O O O D B 4 2 B B B 1 1 9 1 2 3 0 Opt. H. trans. Dummy Opt.Blk. Effective pixels = 1034
