Summary of the content on the page No. 1
INSTRUCTION
MANUAL
650Line Intensifier3™ Series
Focus Free
HTD8FFI
(Weatherproof Color Dome Camera)
HTB11FFI
(Weatherproof Color Bullet Camera)
HT7248FFI
(Weatherproof Color Dome Camera)
Speco Technologies is constantly developing product improvements.
We reserve the right to modify product design and specifications without notice and without incurring any obligation. Rev. 6/9/10
Summary of the content on the page No. 2
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION CAUTION RISK OF ELECTRIC SHOCK RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT OPEN DO NOT REMOVE COVER(OR BACK). CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK NO USER-SER VICEABLE PARTS INSIDE. CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER(OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Summary of the content on the page No. 3
Precautions Do not install the camera in Do not install the camera under Do not touch the front lens of the extreme temperature conditions. unstable lighting conditions. camera. Only use the camera under conditions Severe lighting change or flicker can This is one of the most important parts of the where temperatures are between cause the camera to work improperly. camera. Be careful not to leave -10°C and +50°C. Be especially careful to provide fingerprints on the lens cover. ventilation when
Summary of the content on the page No. 4
650 Line Intensifier3 (Weatherproof Color Dome Camera) Focus Free Focus free AI Motorized zoom Lens(2.8-10mm) ■ HTD8FFI SPECIFICATIONS MODEL HTD8FFI 1/3” Sony Super HAD ll CCD Image Pick-Up Device NTSC, PAL TV System NTSC=811(H) * 508(V) / PAL=795(H) * 596(V) Total Pixels NTSC=768(H) * 494(V) / PAL=752(H) * 582(V) Effective Pixels NTSC=15.734KHz(H) & 59.94Hz(V) / PAL=15.625KHz(H) & 50.00Hz(V) Scanning Frequency 2:1 Interlace Scanning System Internal Synchronization 650TV Lines Resolution CDS OFF
Summary of the content on the page No. 5
650 Line Intensifier3 (Weatherproof Color Bullet Camera) Focus Free Focus free AI Motorized zoom Lens(2.8-10mm) HTB11FFI ■ SPECIFICATIONS MODEL HTB11FFI 1/3” Sony Super HAD ll CCD Image Pick-Up Device NTSC, PAL TV System NTSC=811(H) * 508(V) / PAL=795(H) * 596(V) Total Pixels NTSC=768(H) * 494(V) / PAL=752(H) * 582(V) Effective Pixels NTSC=15.734KHz(H) & 59.94Hz(V) / PAL=15.625KHz(H) & 50.00Hz(V) Scanning Frequency 2:1 Interlace Scanning System Internal Synchronization 650TV Lines Resolution CDS
Summary of the content on the page No. 6
650 Line Intensifier3 (Weatherproof Color Dome Camera) Focus Free Focus free AI Motorized zoom Lens(2.8-10mm) HT7248FFI ■ SPECIFICATIONS MODEL HT7248FFI 1/3” Sony Super HAD ll CCD Image Pick-Up Device NTSC, PAL TV System NTSC=811(H) * 508(V) / PAL=795(H) * 596(V) Total Pixels NTSC=768(H) * 494(V) / PAL=752(H) * 582(V) Effective Pixels NTSC=15.734KHz(H) & 59.94Hz(V) / PAL=15.625KHz(H) & 50.00Hz(V) Scanning Frequency 2:1 Interlace Scanning System Internal Synchronization 650TV Lines Resolution CDS
Summary of the content on the page No. 7
CAMERA INSTALLATION 7
Summary of the content on the page No. 8
Contents ◑ 1 Contents ◑ 2 Safety Instructions ◑ 3 FEATURES ◑ 4 FEATURES ◑ 5 Camera Menu Set Up 5 1. Preset Mode 5 2. Menu Set Up 5 3. Lens Setting 6 4. Exposure Setting 7 5. White Balance Setting 8 6. WDR Setting 9 7. Backlight Setting 10 8. SPECO DNR Setting 11 9. Day/Night Setting 12 10. Special Setting 16 11. RETURN Setting ◑ 17 Trouble Shooting 1
Summary of the content on the page No. 9
Safety Instructions Precautions for use ◑ This camera should be installed by qualified personnel only ◑ There are no user serviceable parts inside ◑ Do not disassemble this camera other than to make initial adjustments ◑ Use a UL approved regulated 24 volt AC or 12 volt DC power supply ◑ Use appropriate low voltage power cable to prevent fire or electrical shock ◑ Please insure that your installation area can support the weight of the camera Please handle this camera carefully : ◑ Do not u
Summary of the content on the page No. 10
FEATURES Now with “PRESETS” PRESETS (Outdoor, Indoor, Elevator, Lobby, Hallway & Low Light) Used for a quick and easy setup for the installation environment. 650TVL Resolution Horizontal resolution of 650 TV lines is achieved by using a SONY Super-HAD CCD with 410,000 pixels, and a custom DSP yielding pictures with a high S/N ratio. INTENSIFIER 3 More Powerful Performance in low light condition. High quality Pictures to be captured in very low light condition. WDR More Powerful WDR in strong bac
Summary of the content on the page No. 11
FEATURES Motion Detection with Alarm Output Built in motion detector with adjustable areas of coverage will Send a signal to an external alarm device when motion is detected. PRIVACY MASK It also has the ability to mask up to 8 areas of the picture where Viewing is not desired. Each zone can be independently programmed via the OSD STABILIZER This function removes image jitter that is caused by vibrations in the building and reduces the amount of hard drive space. DIGITAL ZOOM The picture could b
Summary of the content on the page No. 12
● Preset Mode SPECO TECH 1.PRESET MODE INDOOR 2.MAIN SETUP 3.EXIT RESET 1. Preset : INDOOR / OUTDOOR / LOW LIGHT / HALLWAY / LOBBY / ELEVATOR. - Used for a quick and easy setup for the installation environment. ● Menu Setup 1. Press the Function Setup switch. - Main setup menu is displayed on the monitor screen. MAIN SETUP 1.LENS DC 2.EXPOSURE 3.WHITE BAL ATW 4.WDR OFF 5.BACKLIGHT OFF 6.SPECO DNR ON 7.DAY/NIGHT AUTO 8.SPECIAL 9.RETURN SAVE 2. Select a desired function using the Function Setup sw
Summary of the content on the page No. 13
MAIN SETUP 1.LENS DC 2.EXPOSURE 3.WHITE BAL ATW 3. THE Lens mode has sub menu items as listed below. - BRIGHTNESS : Adjusts the video brightness. - FOCUS ADJ : To adjust the DC lens focus correctly, you must activate the Focus Settings mode under each lens menu. Activate the Focus Settings mode, adjust the lens focus, and then deactivate the settings mode. ☞ NOTE ■ If color rolling occurs when using a DC lens, set Shutter to Fixed (---). ● Exposure Setting MAIN SETUP 1.LENS DC 2.EXPOSURE 3
Summary of the content on the page No. 14
☞ NOTE ■ When the SHUTTER is set to MANUAL or A.FLK mode, INTENSIFY will be disabled. ◆ AGC(AUTO GAIN CONTROL) : The higher the gain level, the brighter the screen - but the higher the noise. * OFF : Deactivates the AGC function. * LOW : Allows automatic gain control from 5.3dB to 32dB. * HIGH : Allows automatic gain control from 5.3dB to 37dB. ◆ INTENSIFY : When it is night or dark, the camera automatically detects the light level and mainta
Summary of the content on the page No. 15
※ Select one of the following 5 modes, as appropriate for your purpose. ◆ ATW : Select this when the color temperature is between 1,700˚K and 11,000˚K. ◆ OUTDOOR : Select this when the color temperature is between 1,700˚K and 11,000˚K. (sodium light inclusion) ◆ INDOOR : Select this when the color temperature is between 4,500˚K and 8,500˚K. ◆ MANUAL : Select this to fine-tune White Balance manually. Set White Balance first by using the ATW or AWC mode. After that
Summary of the content on the page No. 16
● Backlight Setting Unlike conventional cameras, the 650Line Intensifier3™ Series are designed to deliver a distinctive subject and background at the same time, even when the subject is backlight, by using the features of the proprietary W-V DSP chip. 1. When the SETUP menu screen is displayed, select 'BACKLIGHT' by using the Function Setup switch so that the arrow indicates 'BACKLIGHT'. MAIN SETUP 1.LENS DC 2.EXPOSURE 3.WHITE BAL ATW 4.WDR OFF 5.BACKLIGHT OFF 6.SPECO DNR ON 7.DAY/NIGHT AUTO
Summary of the content on the page No. 17
BLC SETUP HLC SETUP LEVEL LOW LEVEL MIDDLE TOP 38 LIMITS NIGHT ONLY BOTTOM 109 MASK COLOR BLACK LEFT 54 MASK TONE 1 RIGHT 121 TOP 5 BOTTOM 120 Press Set to Return LEFT 5 RIGHT 172 Press Set to Return ☞ NOTE ■ Because there can be a difference in the effectiveness of HLC according to the amount of light area in the screen, optimize the installation angle for the best HLC performance. ■ When dark, the HLC is only activated when a bright light exceeding a specific size in NIGHT ONLY mode. ■ Th
Summary of the content on the page No. 18
3. Set the SPECO DNR mode to 'ON' and press the Function Setup switch. Then you can adjust the noise reduction level. NOTE ☞ ■ You cannot set the SPECO DNR to ‘ON’ or ‘OFF’ when the AGC mode of the EXPOSURE menu is ‘OFF’. ■ When adjusting the noise reduction level in the SPECO DNR mode, remember that the higher the level set, the more the noise level will be reduced, as will the brightness of the image. ● Day/Night Setting You can display pictures in color or black and white. 1. When the S
Summary of the content on the page No. 19
◆ AUTO : The mode is switched to 'Color' in a normal environment, but switches to 'B/W' mode when ambient illumination is low. To set up the switching time for AUTO mode, press the Function Setup switch. You can turn on or off the burst signal on B/W mode. AUTO SETUP - BURST MODE : You can turn on or off the burst signal 1.BURST MODE ON on B/W mode. 2.COLOR→B/W DURATION FAST - DURATION : You can select brightness of illumination DWELL TIME 3SEC about cha
Summary of the content on the page No. 20
2. Select a desired mode using the Function Setup switch. SPECIAL 1.IMAGE ADJ 2.MONITOR 3.CAM TITLE OFF 4.SYNC INT 5.MOTION DET OFF 6.PRIVACY OFF 7.COMM ADJ 8.LANGUAGE ENGLISH 9.RETURN ◆ IMAGE ADJ. : 1) When the SETUP menu screen is displayed, select 'IMAGE ADJ' by using the Function Setup switch so that the arrow indicates 'IMAGE ADJ'. 2) Select a desired mode using the Function Setup switch. IMAGE SETUP 1.V-REV 2.H-REV OFF 3.D-ZOOM OFF 4.DIS 5.FONT COLOR WHITE 6.SHARPNESS ON 7.RETURN * V-REV
