Sanyo VCC-HD2500P/HD2500 user manual

User manual for the device Sanyo VCC-HD2500P/HD2500

Device: Sanyo VCC-HD2500P/HD2500
Category: Digital Camera
Manufacturer: Sanyo
Size: 4.38 MB
Added : 2/27/2014
Number of pages: 87
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Sanyo VCC-HD2500P/HD2500. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Sanyo VCC-HD2500P/HD2500.

For your convenience

If looking through the Sanyo VCC-HD2500P/HD2500 user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Sanyo VCC-HD2500P/HD2500 on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Sanyo VCC-HD2500P/HD2500 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Sanyo VCC-HD2500P/HD2500 User manual - Online PDF
Advertisement
« Page 1 of 87 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Sanyo VCC-HD2500P/HD2500 but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Sanyo VCC-HD2500P/HD2500. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 14

Specifications ■ Network Image/video compression H.264/JPEG Video size (H.264) (16:9) 1920×1080, 1280×720, 640×360, 320×180 (4:3) 1600×1200, 1280×960, 1024×768, 640×480, 320×240 Video size (JPEG) (16:9) 1920×1080, 1280×720, 1024×576, 640×360 (4:3) 2288×1712, 1600×1200, 1280×960, 1024×768, 800×600, 640×480, 320×240 Picture quality QUALITY mode: BASIC, NORMAL, ENHANCED, FINE, SUPER FINE BITRATE mode: User-specified bit rate Interface 10BASE-T/100BASE-TX Protocol TCP/IP, UDP, HTTP, HTTPS, SMTP

Summary of the content on the page No. 15

MANUEL ABRÉGÉ VCC-HD2500P/HD2500 VCC-HD2300P/HD2300 VCC-HD2100P/HD2100 Côté A Caméra à mégapixels CETTE INSTALLATION DOIT ETRE EFFECTUEE PAR UNE PERSONNE QUALIFIEE DU SERVICE TECHNIQUE ET DOIT ETRE CONFORME A TOUS LES CODES LOCAUX. Veuillez lire ce manuel d’instructions tres attentivement afin d’effectuer une installation correcte. Veuillez egalement lire tres attentivement le manuel electronique (INSTRUCTION MANUAL) contenu dans le CD-ROM afin de faire fonctionner la camera correctement.

Summary of the content on the page No. 16

Table des matières Nom et fonction de chaque composant ....................................................................2 Branchements de base .............................................................................................5 Branchements des bornes d’alarme .........................................................................6 Réglage de la lentille ................................................................................................7 Réglages du réseau ...........

Summary of the content on the page No. 17

Nom et fonction de chaque composant ■ Face arrière CLASS 2 WIRING AUDIO DC12V Fente pour carte SD (SDHC) (VCC-HD2500P/HD2500) Prise de sortie audio (AUDIO OUT, mini-jack 3,5 mm) (VCC-HD2500P/HD2500) Voyant d’alimentation (POWER) Le voyant d’alimentation clignote pour indiquer les états suivants de la caméra.  Enregistrement vers la carte mémoire SD arrêté/la caméra reconnaît une carte mémoire SD/Une erreur est survenue  Mise à jour du micrologiciel en cours Bornes d’alimentation

Summary of the content on the page No. 18

Nom et fonction de chaque composant ■ Face latérale NEAR FAR RESET SET Boutons de fonction  Redémarrage de la caméra: Appuyez sur le bouton RESET. RÉGLAGES OPTION (RÉAMORCER CAMÉRA)  Arrêter l’enregistrement/retrait de la carte mémoire SD: Appuyez sur le bouton NEAR pendant au moins 2 secondes. Le voyant d’alimentation se met à clignoter et quand la caméra est prête, le voyant s’allume pour vous indiquer que vous pouvez retirer la carte mémoire SD. CARTE MEMOIRE SD (CARTE MEMOIRE SD) 

Summary of the content on the page No. 19

Nom et fonction de chaque composant Prise pour lentille à iris automatique (LENS) Reliez la fiche de câble de l’objectif à la prise de lentille à iris automatique présente sur la face gauche de la caméra. Il est recommandé d’utiliser un objectif à lentille à iris automatique à mégapixels pour monture CS type CD (disponible dans le commerce). 5 mm ou moins Bornes d’objectif pour objectif a iris automatique Bobine de frein (+) Bobine de frein (–) Bobine Bobine d’entraînement (–) d’entraînement

Summary of the content on the page No. 20

Branchements de base VCC-HD2500P VCC-HD2500 PC VCC-HD2500P 24 V CA LAN POWER CLASS2 AC24V WIRING AUDIO DC12V AC24V VCC-HD2300P AC24V ALARM 24 V CA VCC-HD2100P GND AC24V Moniteur GND 12 COM12 IN OUT 12 V CC AC24V Alimentation 12 V CC AC24V électrique GND Branchement électrique Reliez les bornes d’alimentation (24 V CA/12 V CC) de la caméra à une alimentation électrique. Branchement sur une alimentation électrique de 24 V CA Bien que les bornes d’alimentation n’aient pas de polarité, il

Summary of the content on the page No. 1

SUMMARY MANUAL
VCC-HD2500P/HD2500
VCC-HD2300P/HD2300
VCC-HD2100P/HD2100
Side A
Megapixel Camera
THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED
SERVICE PERSON AND SHOULD CONFORM TO ALL LOCAL
CODES.

Please read this instruction manual carefully in order to ensure correct installation.
In addition, be sure to read carefully the electronic manual (INSTRUCTION MANUAL)
contained in the supplied CD-ROM to ensure correct operation of the camera.


De

Summary of the content on the page No. 2

Table of Contents Name and Function of Each Component .................................................................2 Basic Connections ....................................................................................................5 Alarm Terminal Connections ..................................................................................... 6 Lens Adjustment .......................................................................................................7 Network Settings ......

Summary of the content on the page No. 3

Name and Function of Each Component ■ Rear Face CLASS 2 WIRING AUDIO DC12V SD (SDHC) Card Slot (VCC-HD2500P/HD2500) Audio Output Jack (AUDIO OUT, 3.5-mm mini jack) (VCC-HD2500P/HD2500) Power Indicator (POWER) The power indicator blinks to indicate the following camera statuses.  Recording to SD memory card stopped/camera is recognizing SD memory card/ An error occurred  Firmware update in progress Power Terminals (24 V AC/12 V DC) Audio Input Jack (AUDIO IN, 3.5-mm mini jack) (VC

Summary of the content on the page No. 4

Name and Function of Each Component ■ Side Face NEAR FAR RESET SET Operation Buttons  Restarting camera: Press the RESET button. OPTION SETTINGS (CAMERA REBOOT)  Stopping recording/Removing SD memory card: Press the NEAR button for 2 seconds or more. The power indicator starts blinking and then stays lit when the camera is ready for you to remove the SD memory card. SD MEMORY CARD  Resuming stopped recording/Having camera recognize SD memory card: Press the FAR button for 2 seconds o

Summary of the content on the page No. 5

Name and Function of Each Component Auto Iris Lens Socket (LENS) Connect the lens cable plug to the auto iris lens socket provided on the left-side face of the camera. It is recommended that you use a CS-mount DC auto iris megapixel lens (commercially available). 5 mm max. LENS terminal for auto iris lens Brake coil (+) Brake coil (–) Drive coil (–) Drive coil (+) Keep the lens clean at all times. The conversion ring (commercially available) is required to use a C-mount lens. The lens cable

Summary of the content on the page No. 6

Basic Connections VCC-HD2500P VCC-HD2500 PC VCC-HD2500P 24 V AC LAN POWER CLASS2 AC24V WIRING AUDIO DC12V AC24V VCC-HD2300P AC24V ALARM 24 V AC VCC-HD2100P GND AC24V Monitor GND 12 COM 12 IN OUT 12 V DC AC24V Power supply 12 V DC AC24V GND Power Connection Connect the power terminals (24 V AC/12 V DC) of the camera to a power supply. Connection to 24 V AC power supply Although the power terminals have no polarity, the earth grounding wire must be connected to the GND (earth grounding)

Summary of the content on the page No. 7

Alarm Terminal Connections To connect a cable, while pushing the protrusion of the terminal, insert the cable into the opening and then release it. (COM) External (ALARM OUT 2) peripheral (ALARM OUT 1) device Alarm input signal (ALARM IN 2) (COM) Alarm input signal (ALARM IN 1) (COM) Alarm Output Terminal Connection Connect a buzzer, lamp, or other alarm device to one of the alarm output terminals (ALARM OUT 1 or 2).  After connecting an alarm device, configure the output conditions

Summary of the content on the page No. 8

Lens Adjustment For high-resolution megapixel images, the focus assist function is useful to obtain a precise focus because otherwise it is extremely difficult. If you are using a varifocal lens, adjust the focus using the following procedure. If the focus assist function does not work properly because the camera produces too dark or too bright video images, perform iris adjustment in advance. Press the SET button for 2 seconds or more. The monitor now shows the SELECT MENU screen. SE

Summary of the content on the page No. 9

Lens Adjustment ■ Fine-adjusting focus (using buttons provided on side face) NEAR FAR RESET SET Use the zoom lever of the lens to adjust the angle of view and the focus lever of the lens to roughly focus on the subject. Press the SET button. (Focus adjustment screen Page 7) The camera automatically focuses on the subject. Note that the color of the status indicator “FOCUSING” turns from black to orange. If the camera failes to focus on the subject, the FA bar will not operate normally

Summary of the content on the page No. 10

Lens Adjustment ■ Adjusting iris If the camera produces too dark, too bright, or other incorrect video images, adjust the lens iris. Press the SET button for 2 seconds or more. The monitor now shows the SELECT MENU screen. SELECT MENU NEAR FOCUS ASSIST FAR IRIS SET FIRMWARE VERSION NEAR UP FAR DOWN SET SELECT On the SELECT MENU screen, all information is displayed in English. Select [IRIS] using the NEAR/FAR button and press the SET button. The monitor no

Summary of the content on the page No. 11

Network Settings Preparing Your Computer for Network Operation Check your operating environment. ( Page 1) Connect the camera to the network to which your PC is also connected. Configue the network information on your PC. Configure information such as the IP address of your PC. Install the “H.264 Plug-in” from the supplied CD-ROM onto your PC. You are now ready to monitor the surveillance video in the H.264 format. Start Internet Explorer. The supported Web browser is Internet Explorer Ver

Summary of the content on the page No. 12

Network Settings Type your user name and password and click [OK]. The language selection screen appears. If this is the first access to the camera, log in as an admin user (administrator) using the following default authentication information.  User name: admin  Password: admin Click the button corresponding to the language you want to use. The live screen appears. From the second login onwards, the live screen appears automatically by skipping the language selection screen. If this is the

Summary of the content on the page No. 13

Specifications ■ Camera Image pickup device 1/3" CMOS sensor Effective pixels 16:9 1920 (H)×1080 (V), 4:3 2288 (H)×1712 (V) Lowest image illumination 50IRE: 1.0 lx (at F1.2, color mode, high gain) 50IRE: 0.1 lx (at F1.2, black-and-white mode, high gain) Video S/N ratio 50dB (when AGC is “OFF”) Lens mount CS mount Flange back adjustment 12.5 ± 0.5 mm, electrical flange back adjustment (Focus assist function) Iris control DC iris lens supported Digital PTZ Enables electronic pan, tilt, and zoom o


Alternative user manuals
# User manual Category Download
1 Sanyo DUAL CAMERA VPC-PD1GX User manual Digital Camera 9
2 Sanyo EP124 User manual Digital Camera 1
3 Sanyo HD2500 User manual Digital Camera 11
4 Sanyo DUAL CAMERA VPC-PD1PX User manual Digital Camera 1
5 Sanyo HD2300 User manual Digital Camera 17
6 Sanyo DUAL CAMERA VPC-PD1TA User manual Digital Camera 2
7 Sanyo HD2100 User manual Digital Camera 5
8 Sanyo DUAL CAMERA VPC-PD2 User manual Digital Camera 8
9 Sanyo IDC-1000ZU User manual Digital Camera 2
10 Sanyo IDC-1000ZEX User manual Digital Camera 3
11 Sanyo IDC-1000ZE User manual Digital Camera 2
12 Sanyo MEGAPIXEL VCC-HD5400 User manual Digital Camera 5
13 Sanyo VCC-MCH5600 User manual Digital Camera 38
14 Sanyo MEGAPIXEL VCC-HD5400P User manual Digital Camera 38
15 Sanyo VPC-AZ1 User manual Digital Camera 3
16 Sony 3D Bloggie MHS-FS3 User manual Digital Camera 35
17 Sony 838 MHz to 862 MHz User manual Digital Camera 7
18 Sony 4-133-499-11 (1) User manual Digital Camera 15
19 Sony 4-187-045-11(1) User manual Digital Camera 1
20 Sony 4-132-058-11(1) User manual Digital Camera 5