Summary of the content on the page No. 5
Operating Controls and Their Functions 1. Tripod adaptor 1 This adaptor can also be attached on the bottom of the camera. 2 2. Lens mount cap 3. TELE Key When push the TELE KEY, picture is telephoto 4. WIDE Key When push the WIDE KEY, picture is wide angle 5. Focus Near Key In a manual situation, focus get near. 6. Focus Far Key In a manual situation, focus get far. 7. Menu Key If you want to set up a diverse function, you can push this button. 8. Video output (S-Video type) Connect to the S-Vid
Summary of the content on the page No. 6
Power In / Control You can adjust focus and zoom by a pin terminal on the back side 1 6 of the camera. 2 5 3 4 is the color of the cable.(If it is offered) * Adjust voltage from 1 pin and 2 pin 6
Summary of the content on the page No. 7
External Key (A/D IN) Schematic diagram of wired remote-control 1) C300'S 2) C310'S 6.8K 8.2K 12K 18K 33K 68K 180K 7
Summary of the content on the page No. 8
MENU DESCRIPTIONS page 9 page 10 page 12 page 14 page 17 page 19 page 20 page 21 page 22 Using TELE, WIDE, FOCUS+, FOCUS- button • TELE and WIDE are used for UP and DOWN. • FOCUS+ and FOCUS- are used for INCREASE and DECREASE the data. 8
Summary of the content on the page No. 9
CAMERA ID 1. CAMERA ID To connect a large number of camera , It can be assigned to identification number to each camera for camera control easily. (OFF, 0 - 255 : total numbers of ID are 256) • It only can be set this function using ID commend. To transfer ID Code of camera , In first byte at PC control. Set the ID number of camera , and then the ID number display continuously. 9
Summary of the content on the page No. 10
FOCUS MODE SET 2. Focus Set: 2-1. Focus Mode Set : This function is for focus mode setting A) Set up “FOCUS SET” in main menu using Menu key. PUSH Select the “FOCUS MODE” in submenu using Tele/Wide key. And then set the mode (Auto, Push auto, or Manual) using Focus key. 2-2. Focus Distance Set : This function is for selection of minimum shooting distance. A) Select the “FOCUS DIST” in submenu using Tele/wide key. B) Set the focus distance mode from 1cm to 5M. (1cm, 10cm, 50cm, 1M, 3M, 5M) us
Summary of the content on the page No. 11
FOCUS MODE SET 2-4. ZOOM END Set : This function is for selection of zoom end position. A) Select the “ZOOM END” in submenu using Tele/wide key. B) Set the Zoom end mode from (Zoom Start + 1) x 270 to X using PUSH Focus key. 2-5. ZOOM SPEED Set : This function is for selection of zoom speed. A) Select the “ZOOM SPEED” in submenu using Tele/wide key. B) Set the Zoom speed, Slow, Middle , Quick using Focus key. 2-6. ZOOM TRACKING MODE Set : This function is for selection of zoom tracking mode. A)
Summary of the content on the page No. 12
AWB SET 3. AWB SET 3-1. WB Mode Set : This function is for changing the WB mode. A) Set up “AWB SET” in main menu using Tele/wide key. B) Select the “WB MODE” in submenu using Tele/wide key. C) Set the mode Auto, Push auto , Manual, Outdoor, Indoor, Special using Focus key. *WBC MODE ; Use for changing White Balance Mode . 1) AUTO ; WB Range 2800 °K ~ 8000 °K . 2) PUSH AUTO ; Set the AWB mode to Push Auto, then WB Mode is auto. 3) SPECIAL ; Under the special WB condition( Differ from curve of th
Summary of the content on the page No. 13
AWB SET 3-3. BLUE ADJUST Set : This function is available for Special ,Push Auto, Manual WB mode. This mode is the adjustment of user option for special color. A) Select the “BLUE ADJUST” in submenu using Tele/wide key. B) Adjust the level from (-30 to 30 SPECIAL, -128 to +127 PUSH AUTO, 0-255 MANUAL) using Focus key. 3-4. PUSH AUTO : In case of PUSH AUTO WB mode. Adjust the push auto mode ON, WB act automatically. 3-5. INITIAL SET : If initial mode set to ON, All AWB function is changed to
Summary of the content on the page No. 14
AE SET 4. AE SET 4-1. AE Mode Set : This function is for changing to AE mode. A) Set up “AE SET” in main menu using Tele/wide key. B) Select the “AE MODE” in submenu using Tele/wide key. C) Set the mode auto, IRIS MAN, AGC MAN, Manual, Auto using Focus key. 4-2. IRIS ADJUST Set : This function is available for IRIS MAN mode. A) Select the “IRIS ADJUST” in submenu using Tele/wide key. B) Adjust the level from ##MIN to ##MAX(MANUAL, IRIS MAN) using Focus key. * ## : Current level at Auto mode. 4-
Summary of the content on the page No. 15
AE SET 4-4. BRIGHTNESS ADJUSTMENT Set : A) Select the “BRIGHTNESS” in submenu using Tele/wide key. B) Adjust the level from ##MIN to ##MAX. using Focus key. * ## : Current level at Auto mode. 4-5. BACKLIGHT Set : A) Select the “BACKLIGHT” in submenu using Tele/wide key. B) Set the mode OFF, ON, or AUTO using Focus key. * Auto BLC (Auto back light compensation) When a back light condition occurs in area1,area2, area3, or area4. the back light compensation is enable. When the back light conditio
Summary of the content on the page No. 16
AE SET 4-7. SHUTTER SPEED Set : A) Select the “SHUTTER” in submenu using Tele/wide key. B) Set the mode NORMAL, 1/125 - 1/10000 using Focus key. 4-8. INITIAL SET : A) Select the “INITIAL SET” in submenu using Tele/wide Command, B) Set the initial set mode to ON or OFF using Focus key. 4-9. RETURN TO MAIN MENU : This function is exit to main menu. A) Select the “RETURN “ in submenu using Tele/wide key. B) Set the return mode using Focus key. 16
Summary of the content on the page No. 17
SPECIAL SET 5. SPECIAL SET 5-1. User Title Set : This function is for custom title on screen display. A) Set “SPECIAL SET” in main menu using Tele/wide key. B) Select the “USER TITLE” in submenu using Tele/wide key. C) Set the position of title and set data using Tele / Wide, Focus key. 5-2. SHARPNESS ADJUST Set : A) Select the “SHARPNESS” in submenu using Tele/wide key. B) Adjust the level from 0 to 15 using Focus key. 5-3. MIRROR Set : A) Select the “MIRROR” in submenu using Tele/wide key. B)
Summary of the content on the page No. 1
Operating Instructions
LVC-C300HM/HP/NM/NP LVC-C310HM/HP/NM/NP
LVC-C301HM/HP/NM/NP LVC-C311HM/HP/NM/NP
LVC-C302HM/HP/NM/NP LVC-C312HM/HP/NM/NP
LVC-C303HM/HP/NM/NP LVC-C313HM/HP/NM/NP
Before installing and using the camera,
please read these instructions throughly
and retain them for later reference.
Summary of the content on the page No. 2
Warning To prevent fire or shock hazard,do not expose the unit to rain or moisture. CAUTION To avoid electrical shock,do not open the cabinet. Refer servicing to quali- RISK OF ELECTRIC SHOCK fied personnel only. DO NOT OPEN Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70. CAUTION:TO REDUCE THE RISK OF Regulatory Notices For U.S.A ELECTRIC SHOCK, DO NOT REMOVE This equipment has been tested and found to comply with the limits COVER(OR BACK) NO USER SERVICE- f
Summary of the content on the page No. 3
Contents Features............................................................................................................................................................................3 Cautions for Safe Operation ............................................................................................................................................4 Operating Controls and Their Functions.....................................................................................................
Summary of the content on the page No. 4
Cautions for Safe Operation Power Supply • Close to generators of powerful electromagnetic This camera must always be operated a 12V DC radiation such as radio or TV transmitters. UL Listed, Class 2 Power Supply only. Care of the unit Handling of the unit • Remove dust or dirt on the surface of the lens Be careful not to spill water or other liquids on the with a blower. unit, or to get combustible or metallic material • Use a dry soft cloth to clean the body. If it is very inside the body. If u
Summary of the content on the page No. 18
SPECIAL SET 5-5. NEGATIVE Set : This mode is to change color and luminance to negative. A) Select the “COLOR” in submenu using Tele/wide key. B) Select the mode ON, OFF using Focus key. 5-6. WIDE BURST Set : This mode is to change color burst width for long dis- tance application. A) Select the “WIDEBURST” in submenu using Tele/wide key. B) Select the mode ON, OFF using Focus key. 5-7. INITIAL SET : If initial mode set to ON, All SPECIAL functions are changed to the factory setting A) Select
Summary of the content on the page No. 19
MOTION DET 6. MOTION DETECTION SET 6-1. DETECTION Mode Set : A) Set “MOTION” in main menu using Tele/wide key. B) Select the “DETECTION” in submenu. Using Tele/wide key. C) Set the mode ON, OFF using Focus key. 6-2. LEVEL ADJUST Set : This function is available for DETECTION ON mode. A) Select the “LEVEL SET” in submenu. Using Tele/wide key. B) Adjust the level to some sensitivity using Focus key. 6-3. INITIAL SET : If initial mode set to ON, All MOTION functions are changed to the factory sett
Summary of the content on the page No. 20
F. OSD SET 7. F. OSD SET 7-1. FUNCTION Set : A) Set “F. OSD” in main menu using Tele/wide key. B) Select the mode what you want in submenu using Tele/wide key. C) Set the display mode of OSD using Tele / Wide, Near/Far key. *INITIAL SET and RETURN are the same as before procedure. 20
