Summary of the content on the page No. 1
OUTDOOR IMITATION CAMERA
Model 95153
SET Up INSTRUCTIONS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE ThIS MANUAl.
© ®
Copyright 2006 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight
Tools. Diagrams within this manual may not be drawn prop
Summary of the content on the page No. 2
SpECIFICATIONS Batteries Required 2 “AA” Batteries (sold separately) Overall Dimensions 4-1/8” X 11-3/4” L X 4-5/16” H Bracket - 7” High Dimensions Base - 3-1/2” Diameter Weight 2 lb. Features 0-90° Up or Down Tilt, Continuous Blinking LED Save This Manual You will need the manual for the safety warnings and precautions, assembly instruc- tions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the fron
Summary of the content on the page No. 3
9. Replacement parts and accessories. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this product. Approved accessories are available from Harbor Freight Tools. 10. Do not install the Imitation Camera if under the influence of alcohol or drugs. Read warning labels if taking prescription medicine to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do
Summary of the content on the page No. 4
ASSEMbly Pivoting Screw Camera Stand (2) Wall Bracket (1) FIgURE 1 1. Twist the Camera Stand (2) into the Wall Bracket (1). Tilt-up the Pivoting Screw. See Figure 1. Camera Housing (3) Pivoting Screw Wires (4) Camera Stand (2) FIgURE 2 2. Screw the Pivoting Screw into the housing of the Camera. Be sure it is secure. See Figure 2. 3. To make the Camera look more authentic, tuck the Wires (4) into the holes in the Camera Stand (2). See Figure 2. Note: Turn pivot screw 90° if wall bracke
Summary of the content on the page No. 5
bATTERy INSTAllATION Warning: Only install batteries of the same type and charge level. Replace both batteries at once. Install batteries according to polarity markings. Sun-Visor (6) Battery Case (11) Batteries (9) Rear Housing (7) Battery Cover (8) and Battery Cover Screws (5) FIgURE 3 1. Remove the two Battery Cover Screws (5) from the Battery Cover (8) with a screwdriver (sold separately). See Figure 3. 2. Slide the Battery Cover (8) off the Battery Case (11). 3. The Battery Case (11) i
Summary of the content on the page No. 6
INSTAllATION 1. Chose a wall or ceiling location that allows you to mount the unit onto a solid surface capable of sustaining the weight of the unit. If you cannot mount to wall studs, you will need to use the Dry Wall Mounting Anchors and Wood Screws (10). Be aware, the Camera needs to be mounted securely so it will not fall off the mounting and cause personal injury or property damage. Note: The mounting holes on the Outdoor Camera are approximately 1/4” or 6 mm. Mounting Holes Wall Brack
Summary of the content on the page No. 7
pARTS lIST pART # DESCRIpTION QTy. 1 Wall Bracket 1 2 Camera Stand 1 3 Camera Housing 1 4 Coaxial Wire 1 5 Battery Cover Screw (not shown) 2 6 Sun-Visor 1 7 Rear Housing 1 8 Battery Cover (not shown) 1 9 “AA” Battery (not included) 2 10 Drywall Anchor and Wood Screw 3 ea. 11 Battery Case (not shown) 1 pARTS DESCRIpTION 6 3 5 8 pivoting Screw 11 Adjustable 7 Screw 2 4 1 10 Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement par
